MN=xCAT Version 2.14.1.l, centos7.5
node originally installed with 7.5 diskfull install
Followed instructions from:
https://xcat-docs.readthedocs.io/en/stable/advanced/sysclone/sysclone.html
All indications were that it was successfully cloned and the image was
create/cloned onto the mn. But the node never installs the image and boots to
the shell. After installing the original image that was created with copycds I
can successfully install (diskfull). If I attempt to install cloned image, the
node ends up in the genesis shell.
If I boot to the hard drive, I boot into the previous image which tells me that
it's not getting to the point where its installing to the hard drive.
Nodeset n1 <cloned image>
rsetboot n1 boot
rpower n1 reset
[ 9.925415] sd 9:0:0:0: Attached scsi generic sg8 type 0
[ 9.940097] sd 9:0:0:0: [sdi] 4096-byte physical blocks
[ 9.946152] sd 9:0:0:0: [sdi] Write Protect is off
[ 9.951692] sd 9:0:0:0: [sdi] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 9.962556] sd 9:0:0:0: [sdi] Attached SCSI disk
[ 10.329199] cdc_ether 1-1.6:1.0 usb0: kevent 12 may have been dropped
[ 10.336618] cdc_ether 1-1.6:1.0 usb0: kevent 12 may have been dropped
[ 12.968287] igb 0000:03:00.0 eth0: igb: eth0 NIC Link is Up 1000 Mbps Full
Duplex, Flow Control: RX
[ 12.978904] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
xcat.genesis.doxcat: Acquired IPv4 address on eth0
172.20.101.1/16
xcat.genesis.doxcat: Starting ntpd...
xcat.genesis.doxcat: Attempting to sync hardware clock...
xcat.genesis.doxcat: Restarting syslog...
xcat.genesis.doxcat: Getting initial certificate --> mgt:3001
[ 14.534047] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 14.540753] 8021q: adding VLAN 0 to HW filter on device eth1
xcat.genesis.doxcat: Running getdestiny --> mgt:3001
xcat.genesis.doxcat: Received destiny=sysclone centos7.4-x86_64
xcat.genesis.doxcat: The destiny=sysclone, destiny parameters=sysclone
centos7.4-x86_64
xcat.genesis.doxcat: Running dosysclone...
ping_test
Pinging your SystemImager server to ensure we have network connectivity.
PING ATTEMPT 1:
PING mgt.cluster (172.20.0.1) 56(84) bytes of data.
64 bytes from mgt.cluster (172.20.0.1): icmp_seq=1 ttl=64 time=0.125 ms
--- mgt.cluster ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 0.125/0.125/0.125/0.000 ms
We have connectivity to your SystemImager server!
get_scripts_directory
rsync -a mgt::scripts/ /scripts/
/etc/init.d/functions: line 301: rsync: command not found
Last command exited with 127
Killing off running processes.
writsh: no job control in this shell
sh-4.2# e_variables
cat: /etc/issue: No such file or directory
[ 102.185906] random: crng init done
sh-4.2#
Thomas Alandt
Global Engineering
8001 Development Drive, Morrisville, NC 27560
Lenovo USA
[Phone]+1 (919) 237-8959
[Email]+1 (919) 696-8351
[VOIP]2978959
[Email][email protected]<mailto:[email protected]>
Lenovo.com /www.lenovo.com <http://www.lenovo.com/www.lenovo.com>
Twitter<http://twitter.com/lenovo> | Facebook |
Instagram<https://instagram.com/lenovo> | Blogs<http://blog.lenovo.com/> |
Forums<http://forums.lenovo.com/>
[Lenovo_2015]
_______________________________________________
xCAT-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/xcat-user
