On Mon, Oct 26, 2015 at 01:04:03PM +0100, John Doe wrote: > Hi, i'm getting this problem with linux 4.3.0-rcX branch. > Full log is attached. My hardware is based on intel skylake i7-6700k on > z170 chipset and it is working properly. It does boot correctly with > older kernels (3.12). > With mce=off on xen parameters it does boot unti during pci detection > where it hangs (see attached log).
You have some Linux specific options in the Xen command line. For example: iommu=pt iommu=1 unrestricted_guest=1 msi=1 swiotlb=force console=ttyS0 com1=115200,8n1 console=com1 dom0_mem=min:1024Mi loglvl=all apic_verbosity=debug e820f 'swiotlb' is a Linux one. The 'Mi' looks buggy. Did you mean 1024M ? e820f? And I am not seeing the 'mce=off' on the Xen line? Anyhow, if you boot with 'sync_console' you may get more on the console. Doing 'mcelog --ascii' to figure out the MCE does not get much: Hardware event. This is not a software error. CPU 0 BANK 4 MISC 0 STATUS ba00000011000402 MCGSTATUS 0 Which I am not sure what it means .. That would require looking up in the Intel SDM to figure out those bits. > > I tried with both xen 4.4.2 and 4.6.0 with the same effect > > [ 2.957615] VFS: Disk quotas d(XEN) Fatal machine check: MCE: Fatal > error happened on CPUs ff > (XEN) > (XEN) **************************************** > (XEN) > (XEN) The processor has reported a hardware error which cannot > (XEN) be recovered from. Xen will now reboot the machine. > (XEN) mce.c:1533: Begin dump mc_info > (XEN) CPU0: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU0: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU1: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU1: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU2: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU2: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU3: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU3: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) mce.c:1536: End dump mc_info, 8 mcinfo dumped > (XEN) > (XEN) **************************************** > (XEN) Panic on CPU 0: > (XEN) HARDWARE ERROR > (XEN) **************************************** > (XEN) > (XEN) Reboot in five seconds... > > Any help? > > Thanks, > John. > Loading Xen 4.4.2 ... > Loading Linux 4.3.0-1.pvops.qubes.x86_64 ... > Loading initial ramdisk ... > Xen 4.4.2-7.fc21 > (XEN) Xen version 4.4.2 (user@) (gcc (GCC) 4.9.2 20150212 (Red Hat 4.9.2-6)) > debug=n Tue Oct 20 14:48:15 CEST 2015 > (XEN) Latest ChangeSet: > (XEN) Bootloader: GRUB 2.00 > (XEN) Command line: placeholder iommu=pt iommu=1 unrestricted_guest=1 msi=1 > swiotlb=force console=ttyS0 com1=115200,8n1 console=com1 dom0_mem=min:1024Mi > loglvl=all apic_verbosity=debug e820t > (XEN) Video information: > (XEN) VGA is text mode 80x25, font 8x16 > (XEN) VBE/DDC methods: V2; EDID transfer time: 1 seconds > (XEN) Disc information: > (XEN) Found 1 MBR signatures > (XEN) Found 1 EDD information structures > (XEN) Initial Xen-e820 RAM map: > (XEN) 0000000000000000 - 000000000009c800 (usable) > (XEN) 000000000009c800 - 00000000000a0000 (reserved) > (XEN) 00000000000e0000 - 0000000000100000 (reserved) > (XEN) 0000000000100000 - 0000000063911000 (usable) > (XEN) 0000000063911000 - 0000000063912000 (ACPI NVS) > (XEN) 0000000063912000 - 000000006395c000 (reserved) > (XEN) 000000006395c000 - 00000000639af000 (usable) > (XEN) 00000000639af000 - 00000000640b4000 (reserved) > (XEN) 00000000640b4000 - 0000000066b99000 (usable) > (XEN) 0000000066b99000 - 00000000677ab000 (reserved) > (XEN) 00000000677ab000 - 0000000067f9a000 (ACPI NVS) > (XEN) 0000000067f9a000 - 0000000067fff000 (ACPI data) > (XEN) 0000000067fff000 - 0000000068000000 (usable) > (XEN) 0000000100000000 - 0000000892000000 (usable) > (XEN) 0000000068000000 - 0000000068100000 (reserved) > (XEN) 00000000e0000000 - 00000000f0000000 (reserved) > (XEN) 00000000fe000000 - 00000000fe011000 (reserved) > (XEN) 00000000fec00000 - 00000000fec01000 (reserved) > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > (XEN) 00000000ff000000 - 0000000100000000 (reserved) > (XEN) Checking MTRR ranges... > (XEN) MTRR cap: 1d0a type: c06 > (XEN) Xen-e820 RAM map: > (XEN) 0000000000000000 - 000000000009c800 (usable) > (XEN) 000000000009c800 - 00000000000a0000 (reserved) > (XEN) 00000000000e0000 - 0000000000100000 (reserved) > (XEN) 0000000000100000 - 0000000063911000 (usable) > (XEN) 0000000063911000 - 0000000063912000 (ACPI NVS) > (XEN) 0000000063912000 - 000000006395c000 (reserved) > (XEN) 000000006395c000 - 00000000639af000 (usable) > (XEN) 00000000639af000 - 00000000640b4000 (reserved) > (XEN) 00000000640b4000 - 0000000066b99000 (usable) > (XEN) 0000000066b99000 - 00000000677ab000 (reserved) > (XEN) 00000000677ab000 - 0000000067f9a000 (ACPI NVS) > (XEN) 0000000067f9a000 - 0000000067fff000 (ACPI data) > (XEN) 0000000067fff000 - 0000000068000000 (usable) > (XEN) 0000000068000000 - 0000000068100000 (reserved) > (XEN) 00000000e0000000 - 00000000f0000000 (reserved) > (XEN) 00000000fe000000 - 00000000fe011000 (reserved) > (XEN) 00000000fec00000 - 00000000fec01000 (reserved) > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > (XEN) 00000000ff000000 - 0000000100000000 (reserved) > (XEN) 0000000100000000 - 0000000892000000 (usable) > (XEN) ACPI: RSDP 000F05B0, 0024 (r2 ALASKA) > (XEN) ACPI: XSDT 67F59098, 00AC (r1 ALASKA A M I 1072009 AMI 10013) > (XEN) ACPI: FACP 67F7BB20, 010C (r5 ALASKA A M I 1072009 AMI 10013) > (XEN) ACPI: DSDT 67F591D8, 22943 (r2 ALASKA A M I 1072009 INTL 20120913) > (XEN) ACPI: FACS 67F99F80, 0040 > (XEN) ACPI: APIC 67F7BC30, 00BC (r3 ALASKA A M I 1072009 AMI 10013) > (XEN) ACPI: FPDT 67F7BCF0, 0044 (r1 ALASKA A M I 1072009 AMI 10013) > (XEN) ACPI: FIDT 67F7BD38, 009C (r1 ALASKA A M I 1072009 AMI 10013) > (XEN) ACPI: MCFG 67F7BDD8, 003C (r1 ALASKA A M I 1072009 MSFT 97) > (XEN) ACPI: HPET 67F7BE18, 0038 (r1 ALASKA A M I 1072009 AMI. 5000B) > (XEN) ACPI: SSDT 67F7BE50, 036D (r1 SataRe SataTabl 1000 INTL 20120913) > (XEN) ACPI: LPIT 67F7C1C0, 0094 (r1 INTEL SKL 0 MSFT 5F) > (XEN) ACPI: SSDT 67F7C258, 002B (r2 INTEL UsbCTabl 1000 INTL 20120913) > (XEN) ACPI: DBGP 67F7C288, 0034 (r1 INTEL 0 MSFT 5F) > (XEN) ACPI: DBG2 67F7C2C0, 0054 (r0 INTEL 0 MSFT 5F) > (XEN) ACPI: SSDT 67F7C318, 0618 (r2 INTEL xh_rvp08 0 INTL 20120913) > (XEN) ACPI: AAFT 67F7C930, 050A (r1 ALASKA OEMAAFT 1072009 MSFT 97) > (XEN) ACPI: SSDT 67F7CE40, 5212 (r2 SaSsdt SaSsdt 3000 INTL 20120913) > (XEN) ACPI: UEFI 67F82058, 0042 (r1 0 0) > (XEN) ACPI: SSDT 67F820A0, 0E58 (r2 CpuRef CpuSsdt 3000 INTL 20120913) > (XEN) ACPI: ASF! 67F82EF8, 00A5 (r32 INTEL HCG 1 TFSM F4240) > (XEN) System RAM: 32643MB (33427352kB) > (XEN) No NUMA configuration found > (XEN) Faking a node at 0000000000000000-0000000892000000 > (XEN) Domain heap initialised > (XEN) found SMP MP-table at 000fc710 > (XEN) DMI 2.8 present. > (XEN) APIC boot state is 'xapic' > (XEN) Using APIC driver default > (XEN) ACPI: PM-Timer IO Port: 0x1808 > (XEN) ACPI: v5 SLEEP INFO: control[1:1804], status[1:1800] > (XEN) ACPI: Invalid sleep control/status register data: 0:0x8:0x3 0:0x8:0x3 > (XEN) ACPI: SLEEP INFO: pm1x_cnt[1804,0], pm1x_evt[1800,0] > (XEN) ACPI: 32/64X FACS address mismatch in FADT - 67f99f80/0000000000000000, > using 32 > (XEN) ACPI: wakeup_vec[67f99f8c], vec_size[20] > (XEN) ACPI: Local APIC address 0xfee00000 > (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > (XEN) Processor #0 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) > (XEN) Processor #2 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled) > (XEN) Processor #4 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled) > (XEN) Processor #6 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled) > (XEN) Processor #1 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled) > (XEN) Processor #3 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x05] enabled) > (XEN) Processor #5 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled) > (XEN) Processor #7 7:14 APIC version 21 > (XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1]) > (XEN) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > (XEN) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119 > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > (XEN) ACPI: IRQ0 used by override. > (XEN) ACPI: IRQ2 used by override. > (XEN) ACPI: IRQ9 used by override. > (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs > (XEN) ACPI: HPET id: 0x8086a701 base: 0xfed00000 > (XEN) ERST table was not found > (XEN) Using ACPI (MADT) for SMP configuration information > (XEN) SMP: Allowing 8 CPUs (0 hotplug CPUs) > (XEN) mapped APIC to ffff82cfffdfb000 (fee00000) > (XEN) mapped IOAPIC to ffff82cfffdfa000 (fec00000) > (XEN) IRQ limits: 120 GSI, 1432 MSI/MSI-X > (XEN) Not enabling x2APIC: depends on iommu_supports_eim. > (XEN) Using scheduler: SMP Credit Scheduler (credit) > (XEN) Detected 4016.308 MHz processor. > (XEN) Initing memory sharing. > (XEN) mce_intel.c:725: MCA Capability: BCAST 1 SER 0 CMCI 1 firstbank 0 > extended MCE MSR 0 > (XEN) Intel machine check reporting enabled > (XEN) spurious 8259A interrupt: IRQ7. > (XEN) PCI: MCFG configuration 0: base e0000000 segment 0000 buses 00 - ff > (XEN) PCI: MCFG area at e0000000 reserved in E820 > (XEN) PCI: Using MCFG for segment 0000 bus 00-ff > (XEN) I/O virtualisation disabled > (XEN) Getting VERSION: 1060015 > (XEN) Getting VERSION: 1060015 > (XEN) Enabled directed EOI with ioapic_ack_old on! > (XEN) Getting ID: 0 > (XEN) Getting LVT0: 700 > (XEN) Getting LVT1: 400 > (XEN) Suppress EOI broadcast on CPU#0 > (XEN) enabled ExtINT on CPU#0 > (XEN) ESR value before enabling vector: 0x40 after: 0 > (XEN) ENABLING IO-APIC IRQs > (XEN) -> Using old ACK method > (XEN) init IO_APIC IRQs > (XEN) IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, > 2-23, 2-24, 2-25, 2-26, 2-27, 2-28, 2-29, 2-30, 2-31, 2-32, 2-33, 2-34, 2-35, > 2-36, 2-37, 2-38, 2-39, 2-40, 2-41, . > (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=0 pin2=0 > (XEN) number of MP IRQ sources: 15. > (XEN) number of IO-APIC #2 registers: 120. > (XEN) testing the IO APIC....................... > (XEN) IO APIC #2...... > (XEN) .... register #00: 02000000 > (XEN) ....... : physical APIC id: 02 > (XEN) ....... : Delivery Type: 0 > (XEN) ....... : LTS : 0 > (XEN) .... register #01: 00770020 > (XEN) ....... : max redirection entries: 0077 > (XEN) ....... : PRQ implemented: 0 > (XEN) ....... : IO APIC version: 0020 > (XEN) .... register #02: 00000000 > (XEN) ....... : arbitration: 00 > (XEN) .... IRQ redirection table: > (XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: > (XEN) 00 000 00 1 0 0 0 0 0 0 00 > (XEN) 01 001 01 0 0 0 0 0 1 1 28 > (XEN) 02 001 01 0 0 0 0 0 1 1 F0 > (XEN) 03 001 01 0 0 0 0 0 1 1 30 > (XEN) 04 001 01 0 0 0 0 0 1 1 F1 > (XEN) 05 001 01 0 0 0 0 0 1 1 38 > (XEN) 06 001 01 0 0 0 0 0 1 1 40 > (XEN) 07 001 01 0 0 0 0 0 1 1 48 > (XEN) 08 001 01 0 0 0 0 0 1 1 50 > (XEN) 09 001 01 1 1 0 0 0 1 1 58 > (XEN) 0a 001 01 0 0 0 0 0 1 1 60 > (XEN) 0b 001 01 0 0 0 0 0 1 1 68 > (XEN) 0c 001 01 0 0 0 0 0 1 1 70 > (XEN) 0d 001 01 0 0 0 0 0 1 1 78 > (XEN) 0e 001 01 0 0 0 0 0 1 1 88 > (XEN) 0f 001 01 0 0 0 0 0 1 1 90 > (XEN) 10 000 00 1 0 0 0 0 0 0 00 > (XEN) 11 000 00 1 0 0 0 0 0 0 00 > (XEN) 12 000 00 1 0 0 0 0 0 0 00 > (XEN) 13 000 00 1 0 0 0 0 0 0 00 > (XEN) 14 000 00 1 0 0 0 0 0 0 00 > (XEN) 15 000 00 1 0 0 0 0 0 0 00 > (XEN) 16 000 00 1 0 0 0 0 0 0 00 > (XEN) 17 000 00 1 0 0 0 0 0 0 00 > (XEN) 18 000 00 1 0 0 0 0 0 0 00 > (XEN) 19 000 00 1 0 0 0 0 0 0 00 > (XEN) 1a 000 00 1 0 0 0 0 0 0 00 > (XEN) 1b 000 00 1 0 0 0 0 0 0 00 > (XEN) 1c 000 00 1 0 0 0 0 0 0 00 > (XEN) 1d 000 00 1 0 0 0 0 0 0 00 > (XEN) 1e 000 00 1 0 0 0 0 0 0 00 > (XEN) 1f 000 00 1 0 0 0 0 0 0 00 > (XEN) 20 000 00 1 0 0 0 0 0 0 00 > (XEN) 21 000 00 1 0 0 0 0 0 0 00 > (XEN) 22 000 00 1 0 0 0 0 0 0 00 > (XEN) 23 000 00 1 0 0 0 0 0 0 00 > (XEN) 24 000 00 1 0 0 0 0 0 0 00 > (XEN) 25 000 00 1 0 0 0 0 0 0 00 > (XEN) 26 000 00 1 0 0 0 0 0 0 00 > (XEN) 27 000 00 1 0 0 0 0 0 0 00 > (XEN) 28 000 00 1 0 0 0 0 0 0 00 > (XEN) 29 000 00 1 0 0 0 0 0 0 00 > (XEN) 2a 000 00 1 0 0 0 0 0 0 00 > (XEN) 2b 000 00 1 0 0 0 0 0 0 00 > (XEN) 2c 000 00 1 0 0 0 0 0 0 00 > (XEN) 2d 000 00 1 0 0 0 0 0 0 00 > (XEN) 2e 000 00 1 0 0 0 0 0 0 00 > (XEN) 2f 000 00 1 0 0 0 0 0 0 00 > (XEN) 30 000 00 1 0 0 0 0 0 0 00 > (XEN) 31 000 00 1 0 0 0 0 0 0 00 > (XEN) 32 000 00 1 0 0 0 0 0 0 00 > (XEN) 33 000 00 1 0 0 0 0 0 0 00 > (XEN) 34 000 00 1 0 0 0 0 0 0 00 > (XEN) 35 000 00 1 0 0 0 0 0 0 00 > (XEN) 36 000 00 1 0 0 0 0 0 0 00 > (XEN) 37 000 00 1 0 0 0 0 0 0 00 > (XEN) 38 000 00 1 0 0 0 0 0 0 00 > (XEN) 39 000 00 1 0 0 0 0 0 0 00 > (XEN) 3a 000 00 1 0 0 0 0 0 0 00 > (XEN) 3b 000 00 1 0 0 0 0 0 0 00 > (XEN) 3c 000 00 1 0 0 0 0 0 0 00 > (XEN) 3d 000 00 1 0 0 0 0 0 0 00 > (XEN) 3e 000 00 1 0 0 0 0 0 0 00 > (XEN) 3f 000 00 1 0 0 0 0 0 0 00 > (XEN) 40 000 00 1 0 0 0 0 0 0 00 > (XEN) 41 000 00 1 0 0 0 0 0 0 00 > (XEN) 42 000 00 1 0 0 0 0 0 0 00 > (XEN) 43 000 00 1 0 0 0 0 0 0 00 > (XEN) 44 000 00 1 0 0 0 0 0 0 00 > (XEN) 45 000 00 1 0 0 0 0 0 0 00 > (XEN) 46 000 00 1 0 0 0 0 0 0 00 > (XEN) 47 000 00 1 0 0 0 0 0 0 00 > (XEN) 48 000 00 1 0 0 0 0 0 0 00 > (XEN) 49 000 00 1 0 0 0 0 0 0 00 > (XEN) 4a 004 04 1 0 0 0 0 0 2 00 > (XEN) 4b 000 00 1 0 0 0 0 0 0 00 > (XEN) 4c 000 00 1 0 0 0 0 0 0 00 > (XEN) 4d 000 00 1 0 0 0 0 0 0 00 > (XEN) 4e 000 00 1 0 0 0 0 0 0 00 > (XEN) 4f 000 00 1 0 0 0 0 0 0 00 > (XEN) 50 000 00 1 0 0 0 0 0 0 00 > (XEN) 51 000 00 1 0 0 0 0 0 0 00 > (XEN) 52 000 00 1 0 0 0 0 0 0 00 > (XEN) 53 000 00 1 0 0 0 0 0 0 00 > (XEN) 54 000 00 1 0 0 0 0 0 0 00 > (XEN) 55 000 00 1 0 0 0 0 0 0 00 > (XEN) 56 000 00 1 0 0 0 0 0 0 00 > (XEN) 57 000 00 1 0 0 0 0 0 0 00 > (XEN) 58 000 00 1 0 0 0 0 0 0 00 > (XEN) 59 000 00 1 0 0 0 0 0 0 00 > (XEN) 5a 000 00 1 0 0 0 0 0 0 00 > (XEN) 5b 000 00 1 0 0 0 0 0 0 00 > (XEN) 5c 000 00 1 0 0 0 0 0 0 00 > (XEN) 5d 000 00 1 0 0 0 0 0 0 00 > (XEN) 5e 000 00 1 0 0 0 0 0 0 00 > (XEN) 5f 000 00 1 0 0 0 0 0 0 00 > (XEN) 60 000 00 1 0 0 0 0 0 0 00 > (XEN) 61 000 00 1 0 0 0 0 0 0 00 > (XEN) 62 000 00 1 0 0 0 0 0 0 00 > (XEN) 63 000 00 1 0 0 0 0 0 0 00 > (XEN) 64 000 00 1 0 0 0 0 0 0 00 > (XEN) 65 000 00 1 0 0 0 0 0 0 00 > (XEN) 66 000 00 1 0 0 0 0 0 0 00 > (XEN) 67 000 00 1 0 0 0 0 0 0 00 > (XEN) 68 000 00 1 0 0 0 0 0 0 00 > (XEN) 69 000 00 1 0 0 0 0 0 0 00 > (XEN) 6a 000 00 1 0 0 0 0 0 0 00 > (XEN) 6b 000 00 1 0 0 0 0 0 0 00 > (XEN) 6c 000 00 1 0 0 0 0 0 0 00 > (XEN) 6d 000 00 1 0 0 0 0 0 0 00 > (XEN) 6e 000 00 1 0 0 0 0 0 0 00 > (XEN) 6f 000 00 1 0 0 0 0 0 0 00 > (XEN) 70 000 00 1 0 0 0 0 0 0 00 > (XEN) 71 000 00 1 0 0 0 0 0 0 00 > (XEN) 72 000 00 1 0 0 0 0 0 0 00 > (XEN) 73 000 00 1 0 0 0 0 0 0 00 > (XEN) 74 000 00 1 0 0 0 0 0 0 00 > (XEN) 75 000 00 1 0 0 0 0 0 0 00 > (XEN) 76 000 00 1 0 0 0 0 0 0 00 > (XEN) 77 000 00 1 0 0 0 0 0 0 00 > (XEN) Using vector-based indexing > (XEN) IRQ to pin mappings: > (XEN) IRQ240 -> 0:2 > (XEN) IRQ40 -> 0:1 > (XEN) IRQ48 -> 0:3 > (XEN) IRQ241 -> 0:4 > (XEN) IRQ56 -> 0:5 > (XEN) IRQ64 -> 0:6 > (XEN) IRQ72 -> 0:7 > (XEN) IRQ80 -> 0:8 > (XEN) IRQ88 -> 0:9 > (XEN) IRQ96 -> 0:10 > (XEN) IRQ104 -> 0:11 > (XEN) IRQ112 -> 0:12 > (XEN) IRQ120 -> 0:13 > (XEN) IRQ136 -> 0:14 > (XEN) IRQ144 -> 0:15 > (XEN) .................................... done. > (XEN) Using local APIC timer interrupts. > (XEN) calibrating APIC timer ... > (XEN) ..... CPU clock speed is 4007.9587 MHz. > (XEN) ..... host bus clock speed is 23.9997 MHz. > (XEN) ..... bus_scale = 0x1893 > (XEN) TSC deadline timer enabled > (XEN) Platform timer is 23.999MHz HPET > (XEN) Allocated console ring of 64 KiB. > (XEN) mwait-idle: does not run on family 6 model 94 > (XEN) VMX: Supported advanced features: > (XEN) - APIC MMIO access virtualisation > (XEN) - APIC TPR shadow > (XEN) - Extended Page Tables (EPT) > (XEN) - Virtual-Processor Identifiers (VPID) > (XEN) - Virtual NMI > (XEN) - MSR direct-access bitmap > (XEN) - Unrestricted Guest > (XEN) - VMCS shadowing > (XEN) HVM: ASIDs enabled. > (XEN) HVM: VMX enabled > (XEN) HVM: Hardware Assisted Paging (HAP) detected > (XEN) HVM: HAP page sizes: 4kB, 2MB, 1GB > (XEN) Suppress EOI broadcast on CPU#1 > (XEN) masked ExtINT on CPU#1 > (XEN) Suppress EOI broadcast on CPU#2 > (XEN) masked ExtINT on CPU#2 > (XEN) Suppress EOI broadcast on CPU#3 > (XEN) masked ExtINT on CPU#3 > (XEN) Suppress EOI broadcast on CPU#4 > (XEN) masked ExtINT on CPU#4 > (XEN) Suppress EOI broadcast on CPU#5 > (XEN) masked ExtINT on CPU#5 > (XEN) Suppress EOI broadcast on CPU#6 > (XEN) masked ExtINT on CPU#6 > (XEN) Suppress EOI broadcast on CPU#7 > (XEN) masked ExtINT on CPU#7 > (XEN) Brought up 8 CPUs > (XEN) ACPI sleep modes: S3 > (XEN) mcheck_poll: Machine check polling timer started. > (XEN) *** LOADING DOMAIN 0 *** > (XEN) Xen kernel: 64-bit, lsb, compat32 > (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x206c000 > (XEN) PHYSICAL MEMORY ARRANGEMENT: > (XEN) Dom0 alloc.: 0000000870000000->0000000874000000 (8203650 pages to be > allocated) > (XEN) Init. ramdisk: 000000088f1c9000->0000000891fff800 > (XEN) VIRTUAL MEMORY ARRANGEMENT: > (XEN) Loaded kernel: ffffffff81000000->ffffffff8206c000 > (XEN) Init. ramdisk: 0000000000000000->0000000000000000 > (XEN) Phys-Mach map: 0000008000000000->0000008003ecddc8 > (XEN) Start info: ffffffff8206c000->ffffffff8206c4b4 > (XEN) Page tables: ffffffff8206d000->ffffffff82082000 > (XEN) Boot stack: ffffffff82082000->ffffffff82083000 > (XEN) TOTAL: ffffffff80000000->ffffffff82400000 > (XEN) ENTRY ADDRESS: ffffffff81d611f0 > (XEN) Dom0 has maximum 8 VCPUs > (XEN) Scrubbing Free RAM: .done. > (XEN) Initial low memory virq threshold set at 0x4000 pages. > (XEN) Std. Loglevel: All > (XEN) Guest Loglevel: Nothing (Rate-limited: Errors and warnings) > (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to > Xen) > (XEN) Freed 288kB init memory. > mapping kernel into physical memory > about to get started... > [ 0.000000] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC > [ 0.000000] Initializing cgroup subsys cpuset > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Initializing cgroup subsys cpuacct > [ 0.000000] Linux version 4.3.0-1.pvops.qubes.x86_64 (user@qubes-build) > (gcc version 4.9.2 20150212 (Red Hat 4.9.2-6) (GCC) ) #1 SMP Mon Oct 26 > 01:29:22 CET 2015 > [ 0.000000] Command line: placeholder root=/dev/mapper/qubes_dom0-root ro > iommu_inclusive_mapping=1 rd.lvm.lv=qubes_dom0/root rd.luks.uuid=luks-nope > rd.lvn > [ 0.000000] x86/fpu: Legacy x87 FPU detected. > [ 0.000000] x86/fpu: Using 'lazy' FPU context switches. > [ 0.000000] Released 0 page(s) > [ 0.000000] e820: BIOS-provided physical RAM map: > [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009bfff] usable > [ 0.000000] Xen: [mem 0x000000000009c800-0x00000000000fffff] reserved > [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000063910fff] usable > [ 0.000000] Xen: [mem 0x0000000063911000-0x0000000063911fff] ACPI NVS > [ 0.000000] Xen: [mem 0x0000000063912000-0x000000006395bfff] reserved > [ 0.000000] Xen: [mem 0x000000006395c000-0x00000000639aefff] usable > [ 0.000000] Xen: [mem 0x00000000639af000-0x00000000640b3fff] reserved > [ 0.000000] Xen: [mem 0x00000000640b4000-0x0000000066b98fff] usable > [ 0.000000] Xen: [mem 0x0000000066b99000-0x00000000677aafff] reserved > [ 0.000000] Xen: [mem 0x00000000677ab000-0x0000000067f99fff] ACPI NVS > [ 0.000000] Xen: [mem 0x0000000067f9a000-0x0000000067ffefff] ACPI data > [ 0.000000] Xen: [mem 0x0000000067fff000-0x0000000067ffffff] usable > [ 0.000000] Xen: [mem 0x0000000068000000-0x00000000680fffff] reserved > [ 0.000000] Xen: [mem 0x00000000e0000000-0x00000000efffffff] reserved > [ 0.000000] Xen: [mem 0x00000000fe000000-0x00000000fe010fff] reserved > [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved > [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved > [ 0.000000] Xen: [mem 0x00000000ff000000-0x00000000ffffffff] reserved > [ 0.000000] Xen: [mem 0x0000000100000000-0x0000000891ffffff] usable > [ 0.000000] bootconsole [xenboot0] enabled > [ 0.000000] NX (Execute Disable) protection: active > [ 0.000000] SMBIOS 2.8 present. > [ 0.000000] Hypervisor detected: Xen > [ 0.000000] e820: last_pfn = 0x892000 max_arch_pfn = 0x400000000 > [ 0.000000] MTRR: Disabled > [ 0.000000] e820: last_pfn = 0x68000 max_arch_pfn = 0x400000000 > [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] > [ 0.000000] init_memory_mapping: [mem 0x7d9800000-0x7d99fffff] > [ 0.000000] init_memory_mapping: [mem 0x7c0000000-0x7d97fffff] > [ 0.000000] init_memory_mapping: [mem 0x7a0000000-0x7bfffffff] > [ 0.000000] init_memory_mapping: [mem 0x00100000-0x63910fff] > [ 0.000000] init_memory_mapping: [mem 0x6395c000-0x639aefff] > [ 0.000000] init_memory_mapping: [mem 0x640b4000-0x66b98fff] > [ 0.000000] init_memory_mapping: [mem 0x67fff000-0x67ffffff] > [ 0.000000] init_memory_mapping: [mem 0x100000000-0x79fffffff] > [ 0.000000] init_memory_mapping: [mem 0x7d9a00000-0x891ffffff] > [ 0.000000] RAMDISK: [mem 0x04000000-0x06e36fff] > [ 0.000000] ACPI: Early table checksum verification disabled > [ 0.000000] ACPI: RSDP 0x00000000000F05B0 000024 (v02 ALASKA) > [ 0.000000] ACPI: XSDT 0x0000000067F59098 0000AC (v01 ALASKA A M I > 01072009 AMI 00010013) > [ 0.000000] ACPI: FACP 0x0000000067F7BB20 00010C (v05 ALASKA A M I > 01072009 AMI 00010013) > [ 0.000000] ACPI BIOS Warning (bug): Incorrect checksum in table [FACP] - > 0x4B, should be 0x7F (20150818/tbprint-211) > [ 0.000000] ACPI: DSDT 0x0000000067F591D8 022943 (v02 ALASKA A M I > 01072009 INTL 20120913) > [ 0.000000] ACPI: FACS 0x0000000067F99F80 000040 > [ 0.000000] ACPI: APIC 0x0000000067F7BC30 0000BC (v03 ALASKA A M I > 01072009 AMI 00010013) > [ 0.000000] ACPI: FPDT 0x0000000067F7BCF0 000044 (v01 ALASKA A M I > 01072009 AMI 00010013) > [ 0.000000] ACPI: FIDT 0x0000000067F7BD38 00009C (v01 ALASKA A M I > 01072009 AMI 00010013) > [ 0.000000] ACPI: MCFG 0x0000000067F7BDD8 00003C (v01 ALASKA A M I > 01072009 MSFT 00000097) > [ 0.000000] ACPI: HPET 0x0000000067F7BE18 000038 (v01 ALASKA A M I > 01072009 AMI. 0005000B) > [ 0.000000] ACPI: SSDT 0x0000000067F7BE50 00036D (v01 SataRe SataTabl > 00001000 INTL 20120913) > [ 0.000000] ACPI: LPIT 0x0000000067F7C1C0 000094 (v01 INTEL SKL > 00000000 MSFT 0000005F) > [ 0.000000] ACPI: SSDT 0x0000000067F7C258 00002B (v02 INTEL UsbCTabl > 00001000 INTL 20120913) > [ 0.000000] ACPI: DBGP 0x0000000067F7C288 000034 (v01 INTEL > 00000000 MSFT 0000005F) > [ 0.000000] ACPI: DBG2 0x0000000067F7C2C0 000054 (v00 INTEL > 00000000 MSFT 0000005F) > [ 0.000000] ACPI: SSDT 0x0000000067F7C318 000618 (v02 INTEL xh_rvp08 > 00000000 INTL 20120913) > [ 0.000000] ACPI: AAFT 0x0000000067F7C930 00050A (v01 ALASKA OEMAAFT > 01072009 MSFT 00000097) > [ 0.000000] ACPI: SSDT 0x0000000067F7CE40 005212 (v02 SaSsdt SaSsdt > 00003000 INTL 20120913) > [ 0.000000] ACPI: UEFI 0x0000000067F82058 000042 (v01 > 00000000 00000000) > [ 0.000000] ACPI: SSDT 0x0000000067F820A0 000E58 (v02 CpuRef CpuSsdt > 00003000 INTL 20120913) > [ 0.000000] ACPI: ASF! 0x0000000067F82EF8 0000A5 (v32 INTEL HCG > 00000001 TFSM 000F4240) > [ 0.000000] Setting APIC routing to Xen PV. > [ 0.000000] NUMA turned off > [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000891ffffff] > [ 0.000000] NODE_DATA(0) allocated [mem 0x7d9ba5000-0x7d9bb8fff] > [ 0.000000] Zone ranges: > [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] > [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] > [ 0.000000] Normal [mem 0x0000000100000000-0x0000000891ffffff] > [ 0.000000] Movable zone start for each node > [ 0.000000] Early memory node ranges > [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009bfff] > [ 0.000000] node 0: [mem 0x0000000000100000-0x0000000063910fff] > [ 0.000000] node 0: [mem 0x000000006395c000-0x00000000639aefff] > [ 0.000000] node 0: [mem 0x00000000640b4000-0x0000000066b98fff] > [ 0.000000] node 0: [mem 0x0000000067fff000-0x0000000067ffffff] > [ 0.000000] node 0: [mem 0x0000000100000000-0x0000000891ffffff] > [ 0.000000] Initmem setup node 0 [mem > 0x0000000000001000-0x0000000891ffffff] > [ 0.000000] p2m virtual area at ffffc90000000000, size is 4600000 > [ 0.000000] Remapped 629786 page(s) > [ 0.000000] ACPI: PM-Timer IO Port: 0x1808 > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1]) > [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119 > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > [ 0.000000] Using ACPI (MADT) for SMP configuration information > [ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000 > [ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs > [ 0.000000] e820: [mem 0x68100000-0xdfffffff] available for PCI devices > [ 0.000000] Booting paravirtualized kernel on Xen > [ 0.000000] Xen version: 4.4.2 (preserve-AD) > [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: > 0xffffffff, max_idle_ns: 1910969940391419 ns > [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 > nr_node_ids:1 > [ 0.000000] PERCPU: Embedded 34 pages/cpu @ffff880873400000 s99224 r8192 > d31848 u262144 > [ 0.000000] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes) > [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total > pages: 8226238 > [ 0.000000] Policy zone: Normal > [ 0.000000] Kernel command line: placeholder > root=/dev/mapper/qubes_dom0-root ro iommu_inclusive_mapping=1 > rd.lvm.lv=qubes_dom0/root > rd.luks.uuid=luks-78402926-e41f-43b2-8051-0a612a2c055n > [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) > [ 0.000000] software IO TLB [mem 0x86f400000-0x873400000] (64MB) mapped at > [ffff88086f400000-ffff8808733fffff] > [ 0.000000] Memory: 32139548K/33427348K available (7362K kernel code, > 1306K rwdata, 3600K rodata, 1544K init, 1488K bss, 1287800K reserved, 0K > cma-reserved) > [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 > [ 0.000000] Hierarchical RCU implementation. > [ 0.000000] Build-time adjustment of leaf fanout to 64. > [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8. > [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=8 > [ 0.000000] NR_IRQS:4352 nr_irqs:2048 16 > [ 0.000000] xen:events: Using FIFO-based ABI > [ 0.000000] Console: colour VGA+ 80x25 > [ 0.000000] console [hvc0] enabled > [ 0.000000] console [hvc0] enabled > [ 0.000000] bootconsole [xenboot0] disabled > [ 0.000000] bootconsole [xenboot0] disabled > [ 0.000000] clocksource: xen: mask: 0xffffffffffffffff max_cycles: > 0x1cd42e4dffb, max_idle_ns: 881590591483 ns > [ 0.000000] installing Xen timer for CPU 0 > [ 0.000000] tsc: Detected 4016.308 MHz processor > [ 2.750215] Calibrating delay loop (skipped), value calculated using timer > frequency.. 8032.61 BogoMIPS (lpj=4016308) > [ 2.750218] pid_max: default: 32768 minimum: 301 > [ 2.750223] ACPI: Core revision 20150818 > [ 2.790517] ACPI Error: [\_SB_.PCI0.XHC_.RHUB.HS11] Namespace lookup > failure, AE_NOT_FOUND (20150818/dswload-210) > [ 2.790523] ACPI Exception: AE_NOT_FOUND, During name lookup/catalog > (20150818/psobject-227) > [ 2.790553] ACPI Exception: AE_NOT_FOUND, (SSDT:xh_rvp08) while loading > table (20150818/tbxfload-193) > [ 2.802080] ACPI Error: 1 table load failures, 5 successful > (20150818/tbxfload-214) > [ 2.802259] Security Framework initialized > [ 2.802261] AppArmor: AppArmor disabled by boot time parameter > [ 2.804901] Dentry cache hash table entries: 4194304 (order: 13, 33554432 > bytes) > [ 2.809190] Inode-cache hash table entries: 2097152 (order: 12, 16777216 > bytes) > [ 2.810702] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes) > [ 2.810744] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 > bytes) > [ 2.810951] Initializing cgroup subsys io > [ 2.810955] Initializing cgroup subsys memory > [ 2.810961] Initializing cgroup subsys devices > [ 2.810963] Initializing cgroup subsys freezer > [ 2.810965] Initializing cgroup subsys net_cls > [ 2.810968] Initializing cgroup subsys perf_event > [ 2.810970] Initializing cgroup subsys net_prio > [ 2.810972] Initializing cgroup subsys hugetlb > [ 2.811012] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' > [ 2.811014] ENERGY_PERF_BIAS: View and update with > x86_energy_perf_policy(8) > [ 2.811016] CPU: Physical Processor ID: 0 > [ 2.811017] CPU: Processor Core ID: 0 > [ 2.811985] mce: CPU supports 2 MCE banks > [ 2.811995] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8 > [ 2.811996] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4 > [ 2.812212] Freeing SMP alternatives memory: 28K (ffffffff81eca000 - > ffffffff81ed1000) > [ 2.813627] ftrace: allocating 28289 entries in 111 pages > [ 2.820431] cpu 0 spinlock event irq 121 > [ 2.820435] Could not initialize VPMU for cpu 0, error -38 > [ 2.820497] Performance Events: unsupported p6 CPU model 94 no PMU driver, > software events only. > [ 2.820869] NMI watchdog: disabled (cpu0): hardware events not enabled > [ 2.820870] NMI watchdog: Shutting down hard lockup detector on all cpus > [ 2.820903] installing Xen timer for CPU 1 > [ 2.820908] cpu 1 spinlock event irq 128 > [ 2.821962] installing Xen timer for CPU 2 > [ 2.821967] cpu 2 spinlock event irq 135 > [ 2.823005] installing Xen timer for CPU 3 > [ 2.823009] cpu 3 spinlock event irq 142 > [ 2.824043] installing Xen timer for CPU 4 > [ 2.824048] cpu 4 spinlock event irq 149 > [ 2.825095] installing Xen timer for CPU 5 > [ 2.825099] cpu 5 spinlock event irq 156 > [ 2.826149] installing Xen timer for CPU 6 > [ 2.826153] cpu 6 spinlock event irq 163 > [ 2.827211] installing Xen timer for CPU 7 > [ 2.827215] cpu 7 spinlock event irq 170 > [ 2.828240] x86: Booted up 1 node, 8 CPUs > [ 2.828343] devtmpfs: initialized > [ 2.830896] PM: Registering ACPI NVS region [mem 0x63911000-0x63911fff] > (4096 bytes) > [ 2.830899] PM: Registering ACPI NVS region [mem 0x677ab000-0x67f99fff] > (8318976 bytes) > [ 2.831003] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, > max_idle_ns: 1911260446275000 ns > [ 2.831074] atomic64_test: passed for x86-64 platform with CX8 and with SSE > [ 2.831077] pinctrl core: initialized pinctrl subsystem > [ 2.831181] RTC time: 1:25:30, date: 10/26/15 > [ 2.831250] NET: Registered protocol family 16 > [ 2.831257] xen:grant_table: Grant tables using version 1 layout > [ 2.831262] Grant table initialized > [ 2.831462] ACPI FADT declares the system doesn't support PCIe ASPM, so > disable it > [ 2.831465] ACPI: bus type PCI registered > [ 2.831466] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 > [ 2.831608] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem > 0xe0000000-0xefffffff] (base 0xe0000000) > [ 2.831610] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820 > [ 2.846389] PCI: Using configuration type 1 for base access > [ 2.849714] ACPI: Added _OSI(Module Device) > [ 2.849717] ACPI: Added _OSI(Processor Device) > [ 2.849718] ACPI: Added _OSI(3.0 _SCP Extensions) > [ 2.849719] ACPI: Added _OSI(Processor Aggregator Device) > (XEN) IOAPIC[0]: Set PCI routing entry (2-9 -> 0x58 -> IRQ 9 Mode:1 Active:0) > [ 2.854914] ACPI: Executed 21 blocks of module-level executable AML code > [ 2.860184] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored > [ 2.862934] ACPI: Dynamic OEM Table Load: > [ 2.862939] ACPI: SSDT 0xFFFF88086B468C00 00037F (v02 PmRef Cpu0Cst > 00003001 INTL 20120913) > [ 2.863697] ACPI: Dynamic OEM Table Load: > [ 2.863701] ACPI: SSDT 0xFFFF88086B459000 0007AA (v02 PmRef Cpu0Ist > 00003000 INTL 20120913) > [ 2.865192] ACPI: Dynamic OEM Table Load: > [ 2.865196] ACPI: SSDT 0xFFFF88086B459800 0005AA (v02 PmRef ApIst > 00003000 INTL 20120913) > [ 2.865930] ACPI: Dynamic OEM Table Load: > [ 2.865933] ACPI: SSDT 0xFFFF88086B451000 000119 (v02 PmRef ApCst > 00003000 INTL 20120913) > [ 2.870011] ACPI: Interpreter enabled > [ 2.870018] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State > [\_S1_] (20150818/hwxface-580) > [ 2.870024] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State > [\_S2_] (20150818/hwxface-580) > [ 2.870035] ACPI: (supports S0 S3 S5) > [ 2.870036] ACPI: Using IOAPIC for interrupt routing > [ 2.870096] PCI: Using host bridge windows from ACPI; if necessary, use > "pci=nocrs" and report a bug > [ 2.872929] ACPI: Power Resource [WRST] (off) > [ 2.873166] ACPI: Power Resource [WRST] (off) > [ 2.873389] ACPI: Power Resource [WRST] (off) > [ 2.873632] ACPI: Power Resource [WRST] (off) > [ 2.873848] ACPI: Power Resource [WRST] (off) > [ 2.874077] ACPI: Power Resource [WRST] (off) > [ 2.874293] ACPI: Power Resource [WRST] (off) > [ 2.874517] ACPI: Power Resource [WRST] (off) > [ 2.874731] ACPI: Power Resource [WRST] (off) > [ 2.874949] ACPI: Power Resource [WRST] (off) > [ 2.875178] ACPI: Power Resource [WRST] (off) > [ 2.875401] ACPI: Power Resource [WRST] (off) > [ 2.875619] ACPI: Power Resource [WRST] (off) > [ 2.875836] ACPI: Power Resource [WRST] (off) > [ 2.876068] ACPI: Power Resource [WRST] (off) > [ 2.876285] ACPI: Power Resource [WRST] (off) > [ 2.876517] ACPI: Power Resource [WRST] (off) > [ 2.876731] ACPI: Power Resource [WRST] (off) > [ 2.876950] ACPI: Power Resource [WRST] (off) > [ 2.877179] ACPI: Power Resource [WRST] (off) > [ 2.882731] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe]) > [ 2.882736] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM > ClockPM Segments MSI] > [ 2.884227] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER > PCIeCapability] > [ 2.884229] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using > BIOS configuration > [ 2.884791] PCI host bridge to bus 0000:00 > [ 2.884794] pci_bus 0000:00: root bus resource [bus 00-fe] > [ 2.884796] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] > [ 2.884797] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] > [ 2.884799] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff > window] > [ 2.884801] pci_bus 0000:00: root bus resource [mem 0x6d000000-0xdfffffff > window] > [ 2.884803] pci_bus 0000:00: root bus resource [mem 0xfd000000-0xfe7fffff > window] > (XEN) PCI add device 0000:00:00.0 > [ 2.885211] pci 0000:00:01.0: System wakeup disabled by ACPI > (XEN) PCI add device 0000:00:01.0 > [ 2.885395] pci 0000:00:01.1: System wakeup disabled by ACPI > (XEN) PCI add device 0000:00:01.1 > (XEN) PCI add device 0000:00:02.0 > [ 2.885829] pci 0000:00:14.0: System wakeup disabled by ACPI > (XEN) PCI add device 0000:00:14.0 > (XEN) PCI add device 0000:00:14.2 > (XEN) PCI add device 0000:00:16.0 > (XEN) PCI add device 0000:00:17.0 > [ 2.886686] pci 0000:00:1b.0: System wakeup disabled by ACPI > (XEN) PCI add device 0000:00:1b.0 > [ 2.886913] pci 0000:00:1c.0: System wakeup disabled by ACPI > (XEN) PCI add device 0000:00:1c.0 > [ 2.887116] pci 0000:00:1c.2: System wakeup disabled by ACPI > (XEN) PCI add device 0000:00:1c.2 > [ 2.887360] pci 0000:00:1d.0: System wakeup disabled by ACPI > (XEN) PCI add device 0000:00:1d.0 > [ 2.887593] pci 0000:00:1d.7: System wakeup disabled by ACPI > (XEN) PCI add device 0000:00:1d.7 > (XEN) PCI add device 0000:00:1f.0 > (XEN) PCI add device 0000:00:1f.2 > [ 2.888248] pci 0000:00:1f.3: System wakeup disabled by ACPI > (XEN) PCI add device 0000:00:1f.3 > (XEN) PCI add device 0000:00:1f.4 > [ 2.888846] pci 0000:00:1f.6: System wakeup disabled by ACPI > (XEN) PCI add device 0000:00:1f.6 > [ 2.889048] pci 0000:01:00.0: System wakeup disabled by ACPI > (XEN) PCI add device 0000:01:00.0 > [ 2.891464] pci 0000:00:01.0: PCI bridge to [bus 01] > [ 2.891630] pci 0000:02:00.0: System wakeup disabled by ACPI > (XEN) PCI add device 0000:02:00.0 > (XEN) PCI add device 0000:02:00.1 > [ 2.893470] pci 0000:00:01.1: PCI bridge to [bus 02] > [ 2.893578] pci 0000:00:1b.0: PCI bridge to [bus 03] > [ 2.893653] pci 0000:00:1c.0: PCI bridge to [bus 04] > [ 2.893965] pci 0000:05:00.0: System wakeup disabled by ACPI > (XEN) PCI add device 0000:05:00.0 > [ 2.895477] pci 0000:00:1c.2: PCI bridge to [bus 05] > [ 2.895606] pci 0000:00:1d.0: PCI bridge to [bus 06] > [ 2.895686] pci 0000:00:1d.7: PCI bridge to [bus 07] > (XEN) IOAPIC[0]: Set PCI routing entry (2-13 -> 0x78 -> IRQ 13 Mode:0 > Active:0) > [ 2.896904] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15) > [ 2.896985] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 *10 11 12 14 15) > [ 2.897030] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 10 *11 12 14 15) > [ 2.897074] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 10 *11 12 14 15) > [ 2.897119] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 *11 12 14 15) > [ 2.897163] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 *11 12 14 15) > [ 2.897207] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 10 *11 12 14 15) > [ 2.897251] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15) > [ 2.897440] ACPI: Enabled 5 GPEs in block 00 to 7F > [ 2.897466] xen:balloon: Initialising balloon driver > [ 2.898119] xen_balloon: Initialising balloon driver > [ 2.898168] vgaarb: setting as boot device: PCI:0000:01:00.0 > [ 2.898170] vgaarb: device added: > PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none > [ 2.898174] vgaarb: device added: > PCI:0000:02:00.0,decodes=io+mem,owns=none,locks=none > [ 2.898176] vgaarb: loaded > [ 2.898177] vgaarb: bridge control possible 0000:02:00.0 > [ 2.898178] vgaarb: bridge control possible 0000:01:00.0 > [ 2.898214] SCSI subsystem initialized > [ 2.898258] ACPI: bus type USB registered > [ 2.898267] usbcore: registered new interface driver usbfs > [ 2.898272] usbcore: registered new interface driver hub > [ 2.898293] usbcore: registered new device driver usb > [ 2.898405] PCI: Using ACPI for IRQ routing > [ 2.926140] NetLabel: Initializing > [ 2.926141] NetLabel: domain hash size = 128 > [ 2.926142] NetLabel: protocols = UNLABELED CIPSOv4 > [ 2.926149] NetLabel: unlabeled traffic allowed by default > [ 2.926217] clocksource: Switched to clocksource xen > [ 2.929802] pnp: PnP ACPI init > [ 2.930015] system 00:00: [io 0x0280-0x028f] has been reserved > [ 2.930017] system 00:00: [io 0x0290-0x029f] has been reserved > [ 2.930019] system 00:00: [io 0x02a0-0x02af] has been reserved > [ 2.930021] system 00:00: [io 0x02b0-0x02bf] has been reserved > (XEN) IOAPIC[0]: Set PCI routing entry (2-1 -> 0x28 -> IRQ 1 Mode:0 Active:0) > [ 2.930243] Already setup the GSI :4 > [ 2.930340] system 00:03: [io 0x0680-0x069f] has been reserved > [ 2.930342] system 00:03: [io 0xffff] has been reserved > [ 2.930343] system 00:03: [io 0xffff] has been reserved > [ 2.930345] system 00:03: [io 0xffff] has been reserved > [ 2.930346] system 00:03: [io 0x1800-0x18fe] could not be reserved > [ 2.930348] system 00:03: [io 0x164e-0x164f] has been reserved > [ 2.930401] system 00:04: [io 0x0800-0x087f] has been reserved > (XEN) IOAPIC[0]: Set PCI routing entry (2-8 -> 0x50 -> IRQ 8 Mode:0 Active:0) > [ 2.930442] system 00:06: [io 0x1854-0x1857] has been reserved > [ 2.930612] system 00:07: [mem 0xfed10000-0xfed17fff] has been reserved > [ 2.930614] system 00:07: [mem 0xfed18000-0xfed18fff] has been reserved > [ 2.930616] system 00:07: [mem 0xfed19000-0xfed19fff] has been reserved > [ 2.930617] system 00:07: [mem 0xe0000000-0xefffffff] has been reserved > [ 2.930619] system 00:07: [mem 0xfed20000-0xfed3ffff] has been reserved > [ 2.930621] system 00:07: [mem 0xfed90000-0xfed93fff] has been reserved > [ 2.930622] system 00:07: [mem 0xfed45000-0xfed8ffff] has been reserved > [ 2.930624] system 00:07: [mem 0xff000000-0xffffffff] has been reserved > [ 2.930626] system 00:07: [mem 0xfee00000-0xfeefffff] has been reserved > [ 2.930628] system 00:07: [mem 0xdffc0000-0xdffdffff] has been reserved > [ 2.930658] system 00:08: [mem 0xfd000000-0xfdabffff] has been reserved > [ 2.930660] system 00:08: [mem 0xfdad0000-0xfdadffff] has been reserved > [ 2.930661] system 00:08: [mem 0xfdb00000-0xfdffffff] has been reserved > [ 2.930663] system 00:08: [mem 0xfe000000-0xfe01ffff] could not be reserved > [ 2.930665] system 00:08: [mem 0xfe036000-0xfe03bfff] has been reserved > [ 2.930666] system 00:08: [mem 0xfe03d000-0xfe3fffff] has been reserved > [ 2.930668] system 00:08: [mem 0xfe410000-0xfe7fffff] has been reserved > [ 2.930875] system 00:09: [io 0xff00-0xfffe] has been reserved > (XEN) IOAPIC[0]: Set PCI routing entry (2-14 -> 0x88 -> IRQ 14 Mode:1 > Active:1) > [ 2.931660] system 00:0a: [mem 0xfdaf0000-0xfdafffff] has been reserved > [ 2.931662] system 00:0a: [mem 0xfdae0000-0xfdaeffff] has been reserved > [ 2.931663] system 00:0a: [mem 0xfdac0000-0xfdacffff] has been reserved > [ 2.932222] pnp: PnP ACPI: found 11 devices > [ 2.936002] PM-Timer failed consistency check (0xffffff) - aborting. > [ 2.936055] pci 0000:00:01.0: PCI bridge to [bus 01] > [ 2.936059] pci 0000:00:01.0: bridge window [mem 0xdd000000-0xdf0fffff] > [ 2.936063] pci 0000:00:01.0: bridge window [mem 0xc0000000-0xcfffffff > 64bit pref] > [ 2.936068] pci 0000:00:01.1: PCI bridge to [bus 02] > [ 2.936070] pci 0000:00:01.1: bridge window [io 0xe000-0xefff] > [ 2.936074] pci 0000:00:01.1: bridge window [mem 0xdf200000-0xdf2fffff] > [ 2.936078] pci 0000:00:01.1: bridge window [mem 0xa0000000-0xb07fffff > 64bit pref] > [ 2.936083] pci 0000:00:1b.0: PCI bridge to [bus 03] > [ 2.936095] pci 0000:00:1c.0: PCI bridge to [bus 04] > [ 2.936106] pci 0000:00:1c.2: PCI bridge to [bus 05] > [ 2.936111] pci 0000:00:1c.2: bridge window [mem 0xdf100000-0xdf1fffff] > [ 2.936119] pci 0000:00:1d.0: PCI bridge to [bus 06] > [ 2.936130] pci 0000:00:1d.7: PCI bridge to [bus 07] > [ 2.936167] NET: Registered protocol family 2 > [ 2.936410] TCP established hash table entries: 262144 (order: 9, 2097152 > bytes) > [ 2.936654] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) > [ 2.936727] TCP: Hash tables configured (established 262144 bind 65536) > [ 2.936775] UDP hash table entries: 16384 (order: 7, 524288 bytes) > [ 2.936851] UDP-Lite hash table entries: 16384 (order: 7, 524288 bytes) > [ 2.936911] NET: Registered protocol family 1 > [ 2.937471] Unpacking initramfs... > [ 2.956006] Freeing initrd memory: 47324K (ffff880004000000 - > ffff880006e37000) > [ 2.956579] futex hash table entries: 2048 (order: 5, 131072 bytes) > [ 2.956602] audit: initializing netlink subsys (disabled) > [ 2.956610] audit: type=2000 audit(1445822730.952:1): initialized > [ 2.956736] Initialise system trusted keyring > [ 2.956785] HugeTLB registered 2 MB page size, pre-allocated 0 pages > [ 2.957502] zbud: loaded > [ 2.957615] VFS: Disk quotas d(XEN) Fatal machine check: MCE: Fatal error > happened on CPUs ff > (XEN) > (XEN) **************************************** > (XEN) > (XEN) The processor has reported a hardware error which cannot > (XEN) be recovered from. Xen will now reboot the machine. > (XEN) mce.c:1533: Begin dump mc_info > (XEN) CPU0: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU0: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU1: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU1: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU2: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU2: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU3: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) CPU3: Machine Check Exception: 5 > (XEN) Bank 4: ba00000011000402[ 0] > (XEN) mce.c:1536: End dump mc_info, 8 mcinfo dumped > (XEN) > (XEN) **************************************** > (XEN) Panic on CPU 0: > (XEN) HARDWARE ERROR > (XEN) **************************************** > (XEN) > (XEN) Reboot in five seconds... > > Loading Xen 4.4.2 ... > Loading Linux 4.3.0-1.pvops.qubes.x86_64 ... > Loading initial ramdisk ... > Xen 4.4.2-7.fc21 > (XEN) Xen version 4.4.2 (user@) (gcc (GCC) 4.9.2 20150212 (Red Hat 4.9.2-6)) > debug=n Tue Oct 20 14:48:15 CEST 2015 > (XEN) Latest ChangeSet: > (XEN) Bootloader: GRUB 2.00 > (XEN) Command line: placeholder iommu=pt iommu=1 unrestricted_guest=1 msi=1 > swiotlb=force console=ttyS0 com1=115200,8n1 console=com1 dom0_mem=min:1024Mi > loglvl=all apic_verbosity=debug e820f > (XEN) Video information: > (XEN) VGA is text mode 80x25, font 8x16 > (XEN) VBE/DDC methods: V2; EDID transfer time: 1 seconds > (XEN) Disc information: > (XEN) Found 1 MBR signatures > (XEN) Found 1 EDD information structures > (XEN) Initial Xen-e820 RAM map: > (XEN) 0000000000000000 - 000000000009c800 (usable) > (XEN) 000000000009c800 - 00000000000a0000 (reserved) > (XEN) 00000000000e0000 - 0000000000100000 (reserved) > (XEN) 0000000000100000 - 0000000063911000 (usable) > (XEN) 0000000063911000 - 0000000063912000 (ACPI NVS) > (XEN) 0000000063912000 - 000000006395c000 (reserved) > (XEN) 000000006395c000 - 00000000639af000 (usable) > (XEN) 00000000639af000 - 00000000640b4000 (reserved) > (XEN) 00000000640b4000 - 0000000066b99000 (usable) > (XEN) 0000000066b99000 - 00000000677ab000 (reserved) > (XEN) 00000000677ab000 - 0000000067f9a000 (ACPI NVS) > (XEN) 0000000067f9a000 - 0000000067fff000 (ACPI data) > (XEN) 0000000067fff000 - 0000000068000000 (usable) > (XEN) 0000000100000000 - 0000000892000000 (usable) > (XEN) 0000000068000000 - 0000000068100000 (reserved) > (XEN) 00000000e0000000 - 00000000f0000000 (reserved) > (XEN) 00000000fe000000 - 00000000fe011000 (reserved) > (XEN) 00000000fec00000 - 00000000fec01000 (reserved) > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > (XEN) 00000000ff000000 - 0000000100000000 (reserved) > (XEN) Checking MTRR ranges... > (XEN) MTRR cap: 1d0a type: c06 > (XEN) Xen-e820 RAM map: > (XEN) 0000000000000000 - 000000000009c800 (usable) > (XEN) 000000000009c800 - 00000000000a0000 (reserved) > (XEN) 00000000000e0000 - 0000000000100000 (reserved) > (XEN) 0000000000100000 - 0000000063911000 (usable) > (XEN) 0000000063911000 - 0000000063912000 (ACPI NVS) > (XEN) 0000000063912000 - 000000006395c000 (reserved) > (XEN) 000000006395c000 - 00000000639af000 (usable) > (XEN) 00000000639af000 - 00000000640b4000 (reserved) > (XEN) 00000000640b4000 - 0000000066b99000 (usable) > (XEN) 0000000066b99000 - 00000000677ab000 (reserved) > (XEN) 00000000677ab000 - 0000000067f9a000 (ACPI NVS) > (XEN) 0000000067f9a000 - 0000000067fff000 (ACPI data) > (XEN) 0000000067fff000 - 0000000068000000 (usable) > (XEN) 0000000068000000 - 0000000068100000 (reserved) > (XEN) 00000000e0000000 - 00000000f0000000 (reserved) > (XEN) 00000000fe000000 - 00000000fe011000 (reserved) > (XEN) 00000000fec00000 - 00000000fec01000 (reserved) > (XEN) 00000000fee00000 - 00000000fee01000 (reserved) > (XEN) 00000000ff000000 - 0000000100000000 (reserved) > (XEN) 0000000100000000 - 0000000892000000 (usable) > (XEN) ACPI: RSDP 000F05B0, 0024 (r2 ALASKA) > (XEN) ACPI: XSDT 67F59098, 00AC (r1 ALASKA A M I 1072009 AMI 10013) > (XEN) ACPI: FACP 67F7BB20, 010C (r5 ALASKA A M I 1072009 AMI 10013) > (XEN) ACPI: DSDT 67F591D8, 22943 (r2 ALASKA A M I 1072009 INTL 20120913) > (XEN) ACPI: FACS 67F99F80, 0040 > (XEN) ACPI: APIC 67F7BC30, 00BC (r3 ALASKA A M I 1072009 AMI 10013) > (XEN) ACPI: FPDT 67F7BCF0, 0044 (r1 ALASKA A M I 1072009 AMI 10013) > (XEN) ACPI: FIDT 67F7BD38, 009C (r1 ALASKA A M I 1072009 AMI 10013) > (XEN) ACPI: MCFG 67F7BDD8, 003C (r1 ALASKA A M I 1072009 MSFT 97) > (XEN) ACPI: HPET 67F7BE18, 0038 (r1 ALASKA A M I 1072009 AMI. 5000B) > (XEN) ACPI: SSDT 67F7BE50, 036D (r1 SataRe SataTabl 1000 INTL 20120913) > (XEN) ACPI: LPIT 67F7C1C0, 0094 (r1 INTEL SKL 0 MSFT 5F) > (XEN) ACPI: SSDT 67F7C258, 002B (r2 INTEL UsbCTabl 1000 INTL 20120913) > (XEN) ACPI: DBGP 67F7C288, 0034 (r1 INTEL 0 MSFT 5F) > (XEN) ACPI: DBG2 67F7C2C0, 0054 (r0 INTEL 0 MSFT 5F) > (XEN) ACPI: SSDT 67F7C318, 0618 (r2 INTEL xh_rvp08 0 INTL 20120913) > (XEN) ACPI: AAFT 67F7C930, 050A (r1 ALASKA OEMAAFT 1072009 MSFT 97) > (XEN) ACPI: SSDT 67F7CE40, 5212 (r2 SaSsdt SaSsdt 3000 INTL 20120913) > (XEN) ACPI: UEFI 67F82058, 0042 (r1 0 0) > (XEN) ACPI: SSDT 67F820A0, 0E58 (r2 CpuRef CpuSsdt 3000 INTL 20120913) > (XEN) ACPI: ASF! 67F82EF8, 00A5 (r32 INTEL HCG 1 TFSM F4240) > (XEN) System RAM: 32643MB (33427352kB) > (XEN) No NUMA configuration found > (XEN) Faking a node at 0000000000000000-0000000892000000 > (XEN) Domain heap initialised > (XEN) found SMP MP-table at 000fc710 > (XEN) DMI 2.8 present. > (XEN) APIC boot state is 'xapic' > (XEN) Using APIC driver default > (XEN) ACPI: PM-Timer IO Port: 0x1808 > (XEN) ACPI: v5 SLEEP INFO: control[1:1804], status[1:1800] > (XEN) ACPI: Invalid sleep control/status register data: 0:0x8:0x3 0:0x8:0x3 > (XEN) ACPI: SLEEP INFO: pm1x_cnt[1804,0], pm1x_evt[1800,0] > (XEN) ACPI: 32/64X FACS address mismatch in FADT - 67f99f80/0000000000000000, > using 32 > (XEN) ACPI: wakeup_vec[67f99f8c], vec_size[20] > (XEN) ACPI: Local APIC address 0xfee00000 > (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > (XEN) Processor #0 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled) > (XEN) Processor #2 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled) > (XEN) Processor #4 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled) > (XEN) Processor #6 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x05] lapic_id[0x01] enabled) > (XEN) Processor #1 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x06] lapic_id[0x03] enabled) > (XEN) Processor #3 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x07] lapic_id[0x05] enabled) > (XEN) Processor #5 7:14 APIC version 21 > (XEN) ACPI: LAPIC (acpi_id[0x08] lapic_id[0x07] enabled) > (XEN) Processor #7 7:14 APIC version 21 > (XEN) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1]) > (XEN) ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1]) > (XEN) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > (XEN) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119 > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > (XEN) ACPI: IRQ0 used by override. > (XEN) ACPI: IRQ2 used by override. > (XEN) ACPI: IRQ9 used by override. > (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs > (XEN) ACPI: HPET id: 0x8086a701 base: 0xfed00000 > (XEN) ERST table was not found > (XEN) Using ACPI (MADT) for SMP configuration information > (XEN) SMP: Allowing 8 CPUs (0 hotplug CPUs) > (XEN) mapped APIC to ffff82cfffdfb000 (fee00000) > (XEN) mapped IOAPIC to ffff82cfffdfa000 (fec00000) > (XEN) IRQ limits: 120 GSI, 1432 MSI/MSI-X > (XEN) Not enabling x2APIC: depends on iommu_supports_eim. > (XEN) Using scheduler: SMP Credit Scheduler (credit) > (XEN) Detected 4015.837 MHz processor. > (XEN) Initing memory sharing. > (XEN) MCE support disabled by bootparam > (XEN) spurious 8259A interrupt: IRQ7. > (XEN) PCI: MCFG configuration 0: base e0000000 segment 0000 buses 00 - ff > (XEN) PCI: MCFG area at e0000000 reserved in E820 > (XEN) PCI: Using MCFG for segment 0000 bus 00-ff > (XEN) I/O virtualisation disabled > (XEN) Getting VERSION: 1060015 > (XEN) Getting VERSION: 1060015 > (XEN) Enabled directed EOI with ioapic_ack_old on! > (XEN) Getting ID: 0 > (XEN) Getting LVT0: 700 > (XEN) Getting LVT1: 400 > (XEN) Suppress EOI broadcast on CPU#0 > (XEN) enabled ExtINT on CPU#0 > (XEN) ESR value before enabling vector: 0x40 after: 0 > (XEN) ENABLING IO-APIC IRQs > (XEN) -> Using old ACK method > (XEN) init IO_APIC IRQs > (XEN) IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, > 2-23, 2-24, 2-25, 2-26, 2-27, 2-28, 2-29, 2-30, 2-31, 2-32, 2-33, 2-34, 2-35, > 2-36, 2-37, 2-38, 2-39, 2-40, 2-41, . > (XEN) ..TIMER: vector=0xF0 apic1=0 pin1=2 apic2=0 pin2=0 > (XEN) number of MP IRQ sources: 15. > (XEN) number of IO-APIC #2 registers: 120. > (XEN) testing the IO APIC....................... > (XEN) IO APIC #2...... > (XEN) .... register #00: 02000000 > (XEN) ....... : physical APIC id: 02 > (XEN) ....... : Delivery Type: 0 > (XEN) ....... : LTS : 0 > (XEN) .... register #01: 00770020 > (XEN) ....... : max redirection entries: 0077 > (XEN) ....... : PRQ implemented: 0 > (XEN) ....... : IO APIC version: 0020 > (XEN) .... register #02: 00000000 > (XEN) ....... : arbitration: 00 > (XEN) .... IRQ redirection table: > (XEN) NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: > (XEN) 00 000 00 1 0 0 0 0 0 0 00 > (XEN) 01 001 01 0 0 0 0 0 1 1 28 > (XEN) 02 001 01 0 0 0 0 0 1 1 F0 > (XEN) 03 001 01 0 0 0 0 0 1 1 30 > (XEN) 04 001 01 0 0 0 0 0 1 1 F1 > (XEN) 05 001 01 0 0 0 0 0 1 1 38 > (XEN) 06 001 01 0 0 0 0 0 1 1 40 > (XEN) 07 001 01 0 0 0 0 0 1 1 48 > (XEN) 08 001 01 0 0 0 0 0 1 1 50 > (XEN) 09 001 01 1 1 0 0 0 1 1 58 > (XEN) 0a 001 01 0 0 0 0 0 1 1 60 > (XEN) 0b 001 01 0 0 0 0 0 1 1 68 > (XEN) 0c 001 01 0 0 0 0 0 1 1 70 > (XEN) 0d 001 01 0 0 0 0 0 1 1 78 > (XEN) 0e 001 01 0 0 0 0 0 1 1 88 > (XEN) 0f 001 01 0 0 0 0 0 1 1 90 > (XEN) 10 000 00 1 0 0 0 0 0 0 00 > (XEN) 11 000 00 1 0 0 0 0 0 0 00 > (XEN) 12 000 00 1 0 0 0 0 0 0 00 > (XEN) 13 000 00 1 0 0 0 0 0 0 00 > (XEN) 14 000 00 1 0 0 0 0 0 0 00 > (XEN) 15 000 00 1 0 0 0 0 0 0 00 > (XEN) 16 000 00 1 0 0 0 0 0 0 00 > (XEN) 17 000 00 1 0 0 0 0 0 0 00 > (XEN) 18 000 00 1 0 0 0 0 0 0 00 > (XEN) 19 000 00 1 0 0 0 0 0 0 00 > (XEN) 1a 000 00 1 0 0 0 0 0 0 00 > (XEN) 1b 000 00 1 0 0 0 0 0 0 00 > (XEN) 1c 000 00 1 0 0 0 0 0 0 00 > (XEN) 1d 000 00 1 0 0 0 0 0 0 00 > (XEN) 1e 000 00 1 0 0 0 0 0 0 00 > (XEN) 1f 000 00 1 0 0 0 0 0 0 00 > (XEN) 20 000 00 1 0 0 0 0 0 0 00 > (XEN) 21 000 00 1 0 0 0 0 0 0 00 > (XEN) 22 000 00 1 0 0 0 0 0 0 00 > (XEN) 23 000 00 1 0 0 0 0 0 0 00 > (XEN) 24 000 00 1 0 0 0 0 0 0 00 > (XEN) 25 000 00 1 0 0 0 0 0 0 00 > (XEN) 26 000 00 1 0 0 0 0 0 0 00 > (XEN) 27 000 00 1 0 0 0 0 0 0 00 > (XEN) 28 000 00 1 0 0 0 0 0 0 00 > (XEN) 29 000 00 1 0 0 0 0 0 0 00 > (XEN) 2a 000 00 1 0 0 0 0 0 0 00 > (XEN) 2b 000 00 1 0 0 0 0 0 0 00 > (XEN) 2c 000 00 1 0 0 0 0 0 0 00 > (XEN) 2d 000 00 1 0 0 0 0 0 0 00 > (XEN) 2e 000 00 1 0 0 0 0 0 0 00 > (XEN) 2f 000 00 1 0 0 0 0 0 0 00 > (XEN) 30 000 00 1 0 0 0 0 0 0 00 > (XEN) 31 000 00 1 0 0 0 0 0 0 00 > (XEN) 32 000 00 1 0 0 0 0 0 0 00 > (XEN) 33 000 00 1 0 0 0 0 0 0 00 > (XEN) 34 000 00 1 0 0 0 0 0 0 00 > (XEN) 35 000 00 1 0 0 0 0 0 0 00 > (XEN) 36 000 00 1 0 0 0 0 0 0 00 > (XEN) 37 000 00 1 0 0 0 0 0 0 00 > (XEN) 38 000 00 1 0 0 0 0 0 0 00 > (XEN) 39 000 00 1 0 0 0 0 0 0 00 > (XEN) 3a 000 00 1 0 0 0 0 0 0 00 > (XEN) 3b 000 00 1 0 0 0 0 0 0 00 > (XEN) 3c 000 00 1 0 0 0 0 0 0 00 > (XEN) 3d 000 00 1 0 0 0 0 0 0 00 > (XEN) 3e 000 00 1 0 0 0 0 0 0 00 > (XEN) 3f 000 00 1 0 0 0 0 0 0 00 > (XEN) 40 000 00 1 0 0 0 0 0 0 00 > (XEN) 41 000 00 1 0 0 0 0 0 0 00 > (XEN) 42 000 00 1 0 0 0 0 0 0 00 > (XEN) 43 000 00 1 0 0 0 0 0 0 00 > (XEN) 44 000 00 1 0 0 0 0 0 0 00 > (XEN) 45 000 00 1 0 0 0 0 0 0 00 > (XEN) 46 000 00 1 0 0 0 0 0 0 00 > (XEN) 47 000 00 1 0 0 0 0 0 0 00 > (XEN) 48 000 00 1 0 0 0 0 0 0 00 > (XEN) 49 000 00 1 0 0 0 0 0 0 00 > (XEN) 4a 004 04 1 0 0 0 0 0 2 00 > (XEN) 4b 000 00 1 0 0 0 0 0 0 00 > (XEN) 4c 000 00 1 0 0 0 0 0 0 00 > (XEN) 4d 000 00 1 0 0 0 0 0 0 00 > (XEN) 4e 000 00 1 0 0 0 0 0 0 00 > (XEN) 4f 000 00 1 0 0 0 0 0 0 00 > (XEN) 50 000 00 1 0 0 0 0 0 0 00 > (XEN) 51 000 00 1 0 0 0 0 0 0 00 > (XEN) 52 000 00 1 0 0 0 0 0 0 00 > (XEN) 53 000 00 1 0 0 0 0 0 0 00 > (XEN) 54 000 00 1 0 0 0 0 0 0 00 > (XEN) 55 000 00 1 0 0 0 0 0 0 00 > (XEN) 56 000 00 1 0 0 0 0 0 0 00 > (XEN) 57 000 00 1 0 0 0 0 0 0 00 > (XEN) 58 000 00 1 0 0 0 0 0 0 00 > (XEN) 59 000 00 1 0 0 0 0 0 0 00 > (XEN) 5a 000 00 1 0 0 0 0 0 0 00 > (XEN) 5b 000 00 1 0 0 0 0 0 0 00 > (XEN) 5c 000 00 1 0 0 0 0 0 0 00 > (XEN) 5d 000 00 1 0 0 0 0 0 0 00 > (XEN) 5e 000 00 1 0 0 0 0 0 0 00 > (XEN) 5f 000 00 1 0 0 0 0 0 0 00 > (XEN) 60 000 00 1 0 0 0 0 0 0 00 > (XEN) 61 000 00 1 0 0 0 0 0 0 00 > (XEN) 62 000 00 1 0 0 0 0 0 0 00 > (XEN) 63 000 00 1 0 0 0 0 0 0 00 > (XEN) 64 000 00 1 0 0 0 0 0 0 00 > (XEN) 65 000 00 1 0 0 0 0 0 0 00 > (XEN) 66 000 00 1 0 0 0 0 0 0 00 > (XEN) 67 000 00 1 0 0 0 0 0 0 00 > (XEN) 68 000 00 1 0 0 0 0 0 0 00 > (XEN) 69 000 00 1 0 0 0 0 0 0 00 > (XEN) 6a 000 00 1 0 0 0 0 0 0 00 > (XEN) 6b 000 00 1 0 0 0 0 0 0 00 > (XEN) 6c 000 00 1 0 0 0 0 0 0 00 > (XEN) 6d 000 00 1 0 0 0 0 0 0 00 > (XEN) 6e 000 00 1 0 0 0 0 0 0 00 > (XEN) 6f 000 00 1 0 0 0 0 0 0 00 > (XEN) 70 000 00 1 0 0 0 0 0 0 00 > (XEN) 71 000 00 1 0 0 0 0 0 0 00 > (XEN) 72 000 00 1 0 0 0 0 0 0 00 > (XEN) 73 000 00 1 0 0 0 0 0 0 00 > (XEN) 74 000 00 1 0 0 0 0 0 0 00 > (XEN) 75 000 00 1 0 0 0 0 0 0 00 > (XEN) 76 000 00 1 0 0 0 0 0 0 00 > (XEN) 77 000 00 1 0 0 0 0 0 0 00 > (XEN) Using vector-based indexing > (XEN) IRQ to pin mappings: > (XEN) IRQ240 -> 0:2 > (XEN) IRQ40 -> 0:1 > (XEN) IRQ48 -> 0:3 > (XEN) IRQ241 -> 0:4 > (XEN) IRQ56 -> 0:5 > (XEN) IRQ64 -> 0:6 > (XEN) IRQ72 -> 0:7 > (XEN) IRQ80 -> 0:8 > (XEN) IRQ88 -> 0:9 > (XEN) IRQ96 -> 0:10 > (XEN) IRQ104 -> 0:11 > (XEN) IRQ112 -> 0:12 > (XEN) IRQ120 -> 0:13 > (XEN) IRQ136 -> 0:14 > (XEN) IRQ144 -> 0:15 > (XEN) .................................... done. > (XEN) Using local APIC timer interrupts. > (XEN) calibrating APIC timer ... > (XEN) ..... CPU clock speed is 4007.6612 MHz. > (XEN) ..... host bus clock speed is 23.9979 MHz. > (XEN) ..... bus_scale = 0x1892 > (XEN) TSC deadline timer enabled > (XEN) Platform timer is 23.999MHz HPET > (XEN) Allocated console ring of 64 KiB. > (XEN) mwait-idle: does not run on family 6 model 94 > (XEN) VMX: Supported advanced features: > (XEN) - APIC MMIO access virtualisation > (XEN) - APIC TPR shadow > (XEN) - Extended Page Tables (EPT) > (XEN) - Virtual-Processor Identifiers (VPID) > (XEN) - Virtual NMI > (XEN) - MSR direct-access bitmap > (XEN) - Unrestricted Guest > (XEN) - VMCS shadowing > (XEN) HVM: ASIDs enabled. > (XEN) HVM: VMX enabled > (XEN) HVM: Hardware Assisted Paging (HAP) detected > (XEN) HVM: HAP page sizes: 4kB, 2MB, 1GB > (XEN) Suppress EOI broadcast on CPU#1 > (XEN) masked ExtINT on CPU#1 > (XEN) Suppress EOI broadcast on CPU#2 > (XEN) masked ExtINT on CPU#2 > (XEN) Suppress EOI broadcast on CPU#3 > (XEN) masked ExtINT on CPU#3 > (XEN) Suppress EOI broadcast on CPU#4 > (XEN) masked ExtINT on CPU#4 > (XEN) Suppress EOI broadcast on CPU#5 > (XEN) masked ExtINT on CPU#5 > (XEN) Suppress EOI broadcast on CPU#6 > (XEN) masked ExtINT on CPU#6 > (XEN) Suppress EOI broadcast on CPU#7 > (XEN) masked ExtINT on CPU#7 > (XEN) Brought up 8 CPUs > (XEN) ACPI sleep modes: S3 > (XEN) *** LOADING DOMAIN 0 *** > (XEN) Xen kernel: 64-bit, lsb, compat32 > (XEN) Dom0 kernel: 64-bit, PAE, lsb, paddr 0x1000000 -> 0x206c000 > (XEN) PHYSICAL MEMORY ARRANGEMENT: > (XEN) Dom0 alloc.: 0000000870000000->0000000874000000 (8203657 pages to be > allocated) > (XEN) Init. ramdisk: 000000088f1c9000->0000000891fff800 > (XEN) VIRTUAL MEMORY ARRANGEMENT: > (XEN) Loaded kernel: ffffffff81000000->ffffffff8206c000 > (XEN) Init. ramdisk: 0000000000000000->0000000000000000 > (XEN) Phys-Mach map: 0000008000000000->0000008003ecde00 > (XEN) Start info: ffffffff8206c000->ffffffff8206c4b4 > (XEN) Page tables: ffffffff8206d000->ffffffff82082000 > (XEN) Boot stack: ffffffff82082000->ffffffff82083000 > (XEN) TOTAL: ffffffff80000000->ffffffff82400000 > (XEN) ENTRY ADDRESS: ffffffff81d611f0 > (XEN) Dom0 has maximum 8 VCPUs > (XEN) Scrubbing Free RAM: .done. > (XEN) Initial low memory virq threshold set at 0x4000 pages. > (XEN) Std. Loglevel: All > (XEN) Guest Loglevel: Nothing (Rate-limited: Errors and warnings) > (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to > Xen) > (XEN) Freed 288kB init memory. > mapping kernel into physical memory > about to get started... > [ 0.000000] x86/PAT: Configuration [0-7]: WB WT UC- UC WC WP UC UC > [ 0.000000] Initializing cgroup subsys cpuset > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Initializing cgroup subsys cpuacct > [ 0.000000] Linux version 4.3.0-1.pvops.qubes.x86_64 (user@qubes-build) > (gcc version 4.9.2 20150212 (Red Hat 4.9.2-6) (GCC) ) #1 SMP Mon Oct 26 > 01:29:22 CET 2015 > [ 0.000000] Command line: placeholder root=/dev/mapper/qubes_dom0-root ro > iommu_inclusive_mapping=1 rd.lvm.lv=qubes_dom0/root rd.luks.uuid=luks-nope > rd.lvn > [ 0.000000] x86/fpu: Legacy x87 FPU detected. > [ 0.000000] x86/fpu: Using 'lazy' FPU context switches. > [ 0.000000] Released 0 page(s) > [ 0.000000] e820: BIOS-provided physical RAM map: > [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009bfff] usable > [ 0.000000] Xen: [mem 0x000000000009c800-0x00000000000fffff] reserved > [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000063910fff] usable > [ 0.000000] Xen: [mem 0x0000000063911000-0x0000000063911fff] ACPI NVS > [ 0.000000] Xen: [mem 0x0000000063912000-0x000000006395bfff] reserved > [ 0.000000] Xen: [mem 0x000000006395c000-0x00000000639aefff] usable > [ 0.000000] Xen: [mem 0x00000000639af000-0x00000000640b3fff] reserved > [ 0.000000] Xen: [mem 0x00000000640b4000-0x0000000066b98fff] usable > [ 0.000000] Xen: [mem 0x0000000066b99000-0x00000000677aafff] reserved > [ 0.000000] Xen: [mem 0x00000000677ab000-0x0000000067f99fff] ACPI NVS > [ 0.000000] Xen: [mem 0x0000000067f9a000-0x0000000067ffefff] ACPI data > [ 0.000000] Xen: [mem 0x0000000067fff000-0x0000000067ffffff] usable > [ 0.000000] Xen: [mem 0x0000000068000000-0x00000000680fffff] reserved > [ 0.000000] Xen: [mem 0x00000000e0000000-0x00000000efffffff] reserved > [ 0.000000] Xen: [mem 0x00000000fe000000-0x00000000fe010fff] reserved > [ 0.000000] Xen: [mem 0x00000000fec00000-0x00000000fec00fff] reserved > [ 0.000000] Xen: [mem 0x00000000fee00000-0x00000000feefffff] reserved > [ 0.000000] Xen: [mem 0x00000000ff000000-0x00000000ffffffff] reserved > [ 0.000000] Xen: [mem 0x0000000100000000-0x0000000891ffffff] usable > [ 0.000000] bootconsole [xenboot0] enabled > [ 0.000000] NX (Execute Disable) protection: active > [ 0.000000] SMBIOS 2.8 present. > [ 0.000000] Hypervisor detected: Xen > [ 0.000000] e820: last_pfn = 0x892000 max_arch_pfn = 0x400000000 > [ 0.000000] MTRR: Disabled > [ 0.000000] e820: last_pfn = 0x68000 max_arch_pfn = 0x400000000 > [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff] > [ 0.000000] init_memory_mapping: [mem 0x7d9800000-0x7d99fffff] > [ 0.000000] init_memory_mapping: [mem 0x7c0000000-0x7d97fffff] > [ 0.000000] init_memory_mapping: [mem 0x7a0000000-0x7bfffffff] > [ 0.000000] init_memory_mapping: [mem 0x00100000-0x63910fff] > [ 0.000000] init_memory_mapping: [mem 0x6395c000-0x639aefff] > [ 0.000000] init_memory_mapping: [mem 0x640b4000-0x66b98fff] > [ 0.000000] init_memory_mapping: [mem 0x67fff000-0x67ffffff] > [ 0.000000] init_memory_mapping: [mem 0x100000000-0x79fffffff] > [ 0.000000] init_memory_mapping: [mem 0x7d9a00000-0x891ffffff] > [ 0.000000] RAMDISK: [mem 0x04000000-0x06e36fff] > [ 0.000000] ACPI: Early table checksum verification disabled > [ 0.000000] ACPI: RSDP 0x00000000000F05B0 000024 (v02 ALASKA) > [ 0.000000] ACPI: XSDT 0x0000000067F59098 0000AC (v01 ALASKA A M I > 01072009 AMI 00010013) > [ 0.000000] ACPI: FACP 0x0000000067F7BB20 00010C (v05 ALASKA A M I > 01072009 AMI 00010013) > [ 0.000000] ACPI BIOS Warning (bug): Incorrect checksum in table [FACP] - > 0x4B, should be 0x7F (20150818/tbprint-211) > [ 0.000000] ACPI: DSDT 0x0000000067F591D8 022943 (v02 ALASKA A M I > 01072009 INTL 20120913) > [ 0.000000] ACPI: FACS 0x0000000067F99F80 000040 > [ 0.000000] ACPI: APIC 0x0000000067F7BC30 0000BC (v03 ALASKA A M I > 01072009 AMI 00010013) > [ 0.000000] ACPI: FPDT 0x0000000067F7BCF0 000044 (v01 ALASKA A M I > 01072009 AMI 00010013) > [ 0.000000] ACPI: FIDT 0x0000000067F7BD38 00009C (v01 ALASKA A M I > 01072009 AMI 00010013) > [ 0.000000] ACPI: MCFG 0x0000000067F7BDD8 00003C (v01 ALASKA A M I > 01072009 MSFT 00000097) > [ 0.000000] ACPI: HPET 0x0000000067F7BE18 000038 (v01 ALASKA A M I > 01072009 AMI. 0005000B) > [ 0.000000] ACPI: SSDT 0x0000000067F7BE50 00036D (v01 SataRe SataTabl > 00001000 INTL 20120913) > [ 0.000000] ACPI: LPIT 0x0000000067F7C1C0 000094 (v01 INTEL SKL > 00000000 MSFT 0000005F) > [ 0.000000] ACPI: SSDT 0x0000000067F7C258 00002B (v02 INTEL UsbCTabl > 00001000 INTL 20120913) > [ 0.000000] ACPI: DBGP 0x0000000067F7C288 000034 (v01 INTEL > 00000000 MSFT 0000005F) > [ 0.000000] ACPI: DBG2 0x0000000067F7C2C0 000054 (v00 INTEL > 00000000 MSFT 0000005F) > [ 0.000000] ACPI: SSDT 0x0000000067F7C318 000618 (v02 INTEL xh_rvp08 > 00000000 INTL 20120913) > [ 0.000000] ACPI: AAFT 0x0000000067F7C930 00050A (v01 ALASKA OEMAAFT > 01072009 MSFT 00000097) > [ 0.000000] ACPI: SSDT 0x0000000067F7CE40 005212 (v02 SaSsdt SaSsdt > 00003000 INTL 20120913) > [ 0.000000] ACPI: UEFI 0x0000000067F82058 000042 (v01 > 00000000 00000000) > [ 0.000000] ACPI: SSDT 0x0000000067F820A0 000E58 (v02 CpuRef CpuSsdt > 00003000 INTL 20120913) > [ 0.000000] ACPI: ASF! 0x0000000067F82EF8 0000A5 (v32 INTEL HCG > 00000001 TFSM 000F4240) > [ 0.000000] Setting APIC routing to Xen PV. > [ 0.000000] NUMA turned off > [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000891ffffff] > [ 0.000000] NODE_DATA(0) allocated [mem 0x7d9bac000-0x7d9bbffff] > [ 0.000000] Zone ranges: > [ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff] > [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] > [ 0.000000] Normal [mem 0x0000000100000000-0x0000000891ffffff] > [ 0.000000] Movable zone start for each node > [ 0.000000] Early memory node ranges > [ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009bfff] > [ 0.000000] node 0: [mem 0x0000000000100000-0x0000000063910fff] > [ 0.000000] node 0: [mem 0x000000006395c000-0x00000000639aefff] > [ 0.000000] node 0: [mem 0x00000000640b4000-0x0000000066b98fff] > [ 0.000000] node 0: [mem 0x0000000067fff000-0x0000000067ffffff] > [ 0.000000] node 0: [mem 0x0000000100000000-0x0000000891ffffff] > [ 0.000000] Initmem setup node 0 [mem > 0x0000000000001000-0x0000000891ffffff] > [ 0.000000] p2m virtual area at ffffc90000000000, size is 4600000 > [ 0.000000] Remapped 629786 page(s) > [ 0.000000] ACPI: PM-Timer IO Port: 0x1808 > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1]) > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x08] high edge lint[0x1]) > [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119 > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > [ 0.000000] Using ACPI (MADT) for SMP configuration information > [ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000 > [ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs > [ 0.000000] e820: [mem 0x68100000-0xdfffffff] available for PCI devices > [ 0.000000] Booting paravirtualized kernel on Xen > [ 0.000000] Xen version: 4.4.2 (preserve-AD) > [ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: > 0xffffffff, max_idle_ns: 1910969940391419 ns > [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:8 > nr_node_ids:1 > [ 0.000000] PERCPU: Embedded 34 pages/cpu @ffff880873400000 s99224 r8192 > d31848 u262144 > [ 0.000000] PV qspinlock hash table entries: 256 (order: 0, 4096 bytes) > [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total > pages: 8226238 > [ 0.000000] Policy zone: Normal > [ 0.000000] Kernel command line: placeholder > root=/dev/mapper/qubes_dom0-root ro iommu_inclusive_mapping=1 > rd.lvm.lv=qubes_dom0/root > rd.luks.uuid=luks-78402926-e41f-43b2-8051-0a612a2c055n > [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) > [ 0.000000] software IO TLB [mem 0x86f400000-0x873400000] (64MB) mapped at > [ffff88086f400000-ffff8808733fffff] > [ 0.000000] Memory: 32139576K/33427348K available (7362K kernel code, > 1306K rwdata, 3600K rodata, 1544K init, 1488K bss, 1287772K reserved, 0K > cma-reserved) > [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 > [ 0.000000] Hierarchical RCU implementation. > [ 0.000000] Build-time adjustment of leaf fanout to 64. > [ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=8. > [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=8 > [ 0.000000] NR_IRQS:4352 nr_irqs:2048 16 > [ 0.000000] xen:events: Using FIFO-based ABI > [ 0.000000] Console: colour VGA+ 80x25 > [ 0.000000] console [hvc0] enabled > [ 0.000000] console [hvc0] enabled > [ 0.000000] bootconsole [xenboot0] disabled > [ 0.000000] bootconsole [xenboot0] disabled > [ 0.000000] clocksource: xen: mask: 0xffffffffffffffff max_cycles: > 0x1cd42e4dffb, max_idle_ns: 881590591483 ns > [ 0.000000] installing Xen timer for CPU 0 > [ 0.000000] tsc: Detected 4015.836 MHz processor > [ 2.383810] Calibrating delay loop (skipped), value calculated using timer > frequency.. 8031.67 BogoMIPS (lpj=4015836) > [ 2.383813] pid_max: default: 32768 minimum: 301 > [ 2.383817] ACPI: Core revision 20150818 > [ 2.424116] ACPI Error: [\_SB_.PCI0.XHC_.RHUB.HS11] Namespace lookup > failure, AE_NOT_FOUND (20150818/dswload-210) > [ 2.424123] ACPI Exception: AE_NOT_FOUND, During name lookup/catalog > (20150818/psobject-227) > [ 2.424153] ACPI Exception: AE_NOT_FOUND, (SSDT:xh_rvp08) while loading > table (20150818/tbxfload-193) > [ 2.435685] ACPI Error: 1 table load failures, 5 successful > (20150818/tbxfload-214) > [ 2.435824] Security Framework initialized > [ 2.435826] AppArmor: AppArmor disabled by boot time parameter > [ 2.438508] Dentry cache hash table entries: 4194304 (order: 13, 33554432 > bytes) > [ 2.442752] Inode-cache hash table entries: 2097152 (order: 12, 16777216 > bytes) > [ 2.444303] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes) > [ 2.444346] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 > bytes) > [ 2.444551] Initializing cgroup subsys io > [ 2.444555] Initializing cgroup subsys memory > [ 2.444561] Initializing cgroup subsys devices > [ 2.444563] Initializing cgroup subsys freezer > [ 2.444566] Initializing cgroup subsys net_cls > [ 2.444568] Initializing cgroup subsys perf_event > [ 2.444570] Initializing cgroup subsys net_prio > [ 2.444572] Initializing cgroup subsys hugetlb > [ 2.444612] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' > [ 2.444614] ENERGY_PERF_BIAS: View and update with > x86_energy_perf_policy(8) > [ 2.444616] CPU: Physical Processor ID: 0 > [ 2.444617] CPU: Processor Core ID: 0 > [ 2.445546] mce: CPU supports 2 MCE banks > (XEN) domain.c:656:d0 Attempt to change CR4 flags 00002620 -> 00002660 > [ 2.445559] Last level iTLB entries: 4KB 64, 2MB 8, 4MB 8 > [ 2.445560] Last level dTLB entries: 4KB 64, 2MB 0, 4MB 0, 1GB 4 > [ 2.445816] Freeing SMP alternatives memory: 28K (ffffffff81eca000 - > ffffffff81ed1000) > [ 2.447234] ftrace: allocating 28289 entries in 111 pages > [ 2.454040] cpu 0 spinlock event irq 121 > [ 2.454043] Could not initialize VPMU for cpu 0, error -38 > [ 2.454106] Performance Events: unsupported p6 CPU model 94 no PMU driver, > software events only. > [ 2.454479] NMI watchdog: disabled (cpu0): hardware events not enabled > [ 2.454481] NMI watchdog: Shutting down hard lockup detector on all cpus > [ 2.454514] installing Xen timer for CPU 1 > [ 2.454519] cpu 1 spinlock event irq 128 > (XEN) domain.c:656:d0 Attempt to change CR4 flags 00002620 -> 00002660 > [ 2.455577] installing Xen timer for CPU 2 > [ 2.455582] cpu 2 spinlock event irq 135 > (XEN) domain.c:656:d0 Attempt to change CR4 flags 00002620 -> 00002660 > [ 2.456615] installing Xen timer for CPU 3 > [ 2.456619] cpu 3 spinlock event irq 142 > (XEN) domain.c:656:d0 Attempt to change CR4 flags 00002620 -> 00002660 > [ 2.457656] installing Xen timer for CPU 4 > [ 2.457660] cpu 4 spinlock event irq 149 > (XEN) domain.c:656:d0 Attempt to change CR4 flags 00002620 -> 00002660 > [ 2.458711] installing Xen timer for CPU 5 > [ 2.458715] cpu 5 spinlock event irq 156 > (XEN) domain.c:656:d0 Attempt to change CR4 flags 00002620 -> 00002660 > [ 2.459762] installing Xen timer for CPU 6 > [ 2.459766] cpu 6 spinlock event irq 163 > (XEN) domain.c:656:d0 Attempt to change CR4 flags 00002620 -> 00002660 > [ 2.460827] installing Xen timer for CPU 7 > [ 2.460831] cpu 7 spinlock event irq 170 > (XEN) domain.c:656:d0 Attempt to change CR4 flags 00002620 -> 00002660 > [ 2.461858] x86: Booted up 1 node, 8 CPUs > [ 2.461961] devtmpfs: initialized > [ 2.464518] PM: Registering ACPI NVS region [mem 0x63911000-0x63911fff] > (4096 bytes) > [ 2.464520] PM: Registering ACPI NVS region [mem 0x677ab000-0x67f99fff] > (8318976 bytes) > [ 2.464626] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, > max_idle_ns: 1911260446275000 ns > [ 2.464698] atomic64_test: passed for x86-64 platform with CX8 and with SSE > [ 2.464700] pinctrl core: initialized pinctrl subsystem > [ 2.464804] RTC time: 1:28:15, date: 10/26/15 > [ 2.464873] NET: Registered protocol family 16 > [ 2.464880] xen:grant_table: Grant tables using version 1 layout > [ 2.464885] Grant table initialized > [ 2.465085] ACPI FADT declares the system doesn't support PCIe ASPM, so > disable it > [ 2.465088] ACPI: bus type PCI registered > [ 2.465089] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 > [ 2.465231] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem > 0xe0000000-0xefffffff] (base 0xe0000000) > [ 2.465234] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820 > [ 2.480013] PCI: Using configuration type 1 for base access > [ 2.483344] ACPI: Added _OSI(Module Device) > [ 2.483346] ACPI: Added _OSI(Processor Device) > [ 2.483348] ACPI: Added _OSI(3.0 _SCP Extensions) > [ 2.483349] ACPI: Added _OSI(Processor Aggregator Device) > (XEN) IOAPIC[0]: Set PCI routing entry (2-9 -> 0x58 -> IRQ 9 Mode:1 Active:0) > [ 2.488538] ACPI: Executed 21 blocks of module-level executable AML code > [ 2.493795] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored > [ 2.496545] ACPI: Dynamic OEM Table Load: > [ 2.496550] ACPI: SSDT 0xFFFF88086B428C00 00037F (v02 PmRef Cpu0Cst > 00003001 INTL 20120913) > [ 2.497301] ACPI: Dynamic OEM Table Load: > [ 2.497305] ACPI: SSDT 0xFFFF88086B411800 0007AA (v02 PmRef Cpu0Ist > 00003000 INTL 20120913) > [ 2.498794] ACPI: Dynamic OEM Table Load: > [ 2.498798] ACPI: SSDT 0xFFFF88086B412000 0005AA (v02 PmRef ApIst > 00003000 INTL 20120913) > [ 2.499521] ACPI: Dynamic OEM Table Load: > [ 2.499524] ACPI: SSDT 0xFFFF88086BBE5A00 000119 (v02 PmRef ApCst > 00003000 INTL 20120913) > [ 2.503583] ACPI: Interpreter enabled > [ 2.503590] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State > [\_S1_] (20150818/hwxface-580) > [ 2.503597] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State > [\_S2_] (20150818/hwxface-580) > [ 2.503607] ACPI: (supports S0 S3 S5) > [ 2.503609] ACPI: Using IOAPIC for interrupt routing > [ 2.503669] PCI: Using host bridge windows from ACPI; if necessary, use > "pci=nocrs" and report a bug > [ 2.506493] ACPI: Power Resource [WRST] (off) > [ 2.506728] ACPI: Power Resource [WRST] (off) > [ 2.506949] ACPI: Power Resource [WRST] (off) > [ 2.507165] ACPI: Power Resource [WRST] (off) > [ 2.507379] ACPI: Power Resource [WRST] (off) > [ 2.507608] ACPI: Power Resource [WRST] (off) > [ 2.507822] ACPI: Power Resource [WRST] (off) > [ 2.508044] ACPI: Power Resource [WRST] (off) > [ 2.508259] ACPI: Power Resource [WRST] (off) > [ 2.508475] ACPI: Power Resource [WRST] (off) > [ 2.508703] ACPI: Power Resource [WRST] (off) > [ 2.508921] ACPI: Power Resource [WRST] (off) > [ 2.509144] ACPI: Power Resource [WRST] (off) > [ 2.509360] ACPI: Power Resource [WRST] (off) > [ 2.509588] ACPI: Power Resource [WRST] (off) > [ 2.509806] ACPI: Power Resource [WRST] (off) > [ 2.510040] ACPI: Power Resource [WRST] (off) > [ 2.510254] ACPI: Power Resource [WRST] (off) > [ 2.510470] ACPI: Power Resource [WRST] (off) > [ 2.510702] ACPI: Power Resource [WRST] (off) > [ 2.516247] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe]) > [ 2.516252] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM > ClockPM Segments MSI] > [ 2.517742] acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER > PCIeCapability] > [ 2.517744] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using > BIOS configuration > [ 2.518312] PCI host bridge to bus 0000:00 > [ 2.518314] pci_bus 0000:00: root bus resource [bus 00-fe] > [ 2.518316] pci_bus 0000:00: ro > > _______________________________________________ > Xen-devel mailing list > Xen-devel@lists.xen.org > http://lists.xen.org/xen-devel _______________________________________________ Xen-devel mailing list Xen-devel@lists.xen.org http://lists.xen.org/xen-devel