Similar to the EHCI driver - save/restore relevant BAR and command register, re-configure DbC on resume and stop/start timer. On resume trigger sending anything that was queued in the meantime. Save full BAR value, instead of just the address part, to ease restoring on resume.
Signed-off-by: Marek Marczykowski-Górecki <marma...@invisiblethingslab.com> Acked-by: Jan Beulich <jbeul...@suse.com> --- Changes in v8: - move 'bool suspended' to other bools New in v7 Without this patch, the console is broken after S3, and in some cases the suspend doesn't succeed at all (when xhci console is enabled). Very similar (if not the same) functions might be used for coordinated reset handling. I tried to include it in this patch too, but it's a bit more involved, mostly due to share=yes case (PHYSDEVOP_dbgp_op can be called by the hardware domain only). --- xen/drivers/char/xhci-dbc.c | 55 +++++++++++++++++++++++++++++++++----- 1 file changed, 49 insertions(+), 6 deletions(-) diff --git a/xen/drivers/char/xhci-dbc.c b/xen/drivers/char/xhci-dbc.c index 43ed64a004e2..86f6df6bef67 100644 --- a/xen/drivers/char/xhci-dbc.c +++ b/xen/drivers/char/xhci-dbc.c @@ -251,14 +251,17 @@ struct dbc { struct xhci_string_descriptor *dbc_str; pci_sbdf_t sbdf; - uint64_t xhc_mmio_phys; + uint64_t bar_val; uint64_t xhc_dbc_offset; void __iomem *xhc_mmio; bool enable; /* whether dbgp=xhci was set at all */ bool open; + bool suspended; enum xhci_share share; unsigned int xhc_num; /* look for n-th xhc */ + /* state saved across suspend */ + uint16_t pci_cr; }; static void *dbc_sys_map_xhc(uint64_t phys, size_t size) @@ -358,8 +361,9 @@ static bool __init dbc_init_xhc(struct dbc *dbc) pci_conf_write16(dbc->sbdf, PCI_COMMAND, cmd); - dbc->xhc_mmio_phys = (bar0 & PCI_BASE_ADDRESS_MEM_MASK) | (bar1 << 32); - dbc->xhc_mmio = dbc_sys_map_xhc(dbc->xhc_mmio_phys, xhc_mmio_size); + dbc->bar_val = bar0 | (bar1 << 32); + dbc->xhc_mmio = dbc_sys_map_xhc(dbc->bar_val & PCI_BASE_ADDRESS_MEM_MASK, + xhc_mmio_size); if ( dbc->xhc_mmio == NULL ) return false; @@ -979,6 +983,9 @@ static bool dbc_ensure_running(struct dbc *dbc) uint32_t ctrl; uint16_t cmd; + if ( dbc->suspended ) + return false; + if ( dbc->share != XHCI_SHARE_NONE ) { /* @@ -1213,9 +1220,11 @@ static void __init cf_check dbc_uart_init_postirq(struct serial_port *port) * page, so keep it simple. */ if ( rangeset_add_range(mmio_ro_ranges, - PFN_DOWN(uart->dbc.xhc_mmio_phys + uart->dbc.xhc_dbc_offset), - PFN_UP(uart->dbc.xhc_mmio_phys + uart->dbc.xhc_dbc_offset + - sizeof(*uart->dbc.dbc_reg)) - 1) ) + PFN_DOWN((uart->dbc.bar_val & PCI_BASE_ADDRESS_MEM_MASK) + + uart->dbc.xhc_dbc_offset), + PFN_UP((uart->dbc.bar_val & PCI_BASE_ADDRESS_MEM_MASK) + + uart->dbc.xhc_dbc_offset + + sizeof(*uart->dbc.dbc_reg)) - 1) ) printk(XENLOG_INFO "Error while adding MMIO range of device to mmio_ro_ranges\n"); #endif @@ -1255,6 +1264,38 @@ static void cf_check dbc_uart_flush(struct serial_port *port) set_timer(&uart->timer, goal); } +static void cf_check dbc_uart_suspend(struct serial_port *port) +{ + struct dbc_uart *uart = port->uart; + struct dbc *dbc = &uart->dbc; + + dbc_pop_events(dbc); + stop_timer(&uart->timer); + dbc->pci_cr = pci_conf_read16(dbc->sbdf, PCI_COMMAND); + dbc->suspended = true; +} + +static void cf_check dbc_uart_resume(struct serial_port *port) +{ + struct dbc_uart *uart = port->uart; + struct dbc *dbc = &uart->dbc; + + pci_conf_write32(dbc->sbdf, PCI_BASE_ADDRESS_0, dbc->bar_val & 0xFFFFFFFF); + pci_conf_write32(dbc->sbdf, PCI_BASE_ADDRESS_1, dbc->bar_val >> 32); + pci_conf_write16(dbc->sbdf, PCI_COMMAND, dbc->pci_cr); + + if ( !dbc_init_dbc(dbc) ) + { + dbc_error("resume failed\n"); + return; + } + + dbc_enable_dbc(dbc); + dbc->suspended = false; + dbc_flush(dbc, &dbc->dbc_oring, &dbc->dbc_owork); + set_timer(&uart->timer, NOW() + MICROSECS(DBC_POLL_INTERVAL)); +} + static struct uart_driver dbc_uart_driver = { .init_preirq = dbc_uart_init_preirq, .init_postirq = dbc_uart_init_postirq, @@ -1262,6 +1303,8 @@ static struct uart_driver dbc_uart_driver = { .putc = dbc_uart_putc, .getc = dbc_uart_getc, .flush = dbc_uart_flush, + .suspend = dbc_uart_suspend, + .resume = dbc_uart_resume, }; /* Those are accessed via DMA. */ -- git-series 0.9.1