Please visit us at: [ http://www.wolframmathcore.com/ | wolframmathcore.com ] or [ http://www.wolfram.com/ | wolfram.com ]
----- Den 18 feb 2019, på kl 14:08, Per Öberg p...@wolfram.com skrev: > ----- Den 18 feb 2019, på kl 13:43, Jan Kiszka jan.kis...@siemens.com skrev: > > On 18.02.19 13:36, Per Oberg via Xenomai wrote: > > > Hello list > >> I have this issue where my e1000e network card gets into some kind of > >> cyclic > >> hardware reset during operation. The weird thing is that this only happens > >> when > >> I let systemd start the application. If it's started manually it always > >> works > > > as intended. > >> I am running xenomai 3.0.7 with a linux-4.9.38 kernel and I use the network > > > connection in Linux non-rt mode. I use systemd and NetworkManager. > >> I do realize that once I get into the reset it will continue resetting > >> because I > >> keep flooding the buffers. My issue is that it -never- happens when I > >> start my > >> process manually, only when systemd starts it. Because the network goes > >> down > >> quite badly I cannot log in and disable the service once it happens and > >> therefore I cannot really try starting it manually after letting the > >> network > > > recover. > >> There is some information from intel in [1] below. There is talk about > >> power > > > management function and EPROM etc. They specifically write: > > > "82573(V/L/E) TX Unit Hang Messages > >> Several adapters with the 82573 chipset display "TX unit hang" messages > >> during > >> normal operation with the e1000 driver. The issue appears both with TSO > >> enabled > >> and disabled, and is caused by a power management function that is enabled > >> in > >> the EEPROM. Early releases of the chipsets to vendors had the EEPROM bit > >> that > >> enabled the feature. After the issue was discovered newer adapters were > > > released with the feature disabled in the EEPROM." > > > I also read something about disabling GRO/TSO/GSO that helped some people. > > > My questions to the list are: > > > 1. Have you guys any experience with this? > > > 2. Would I be better of using the RT Net drivers? > >> 3. What could cause the issue to trigger only when run by systemd. (I > >> thought > > > about timing issues and NetworkManager, but how do I debug this?) > >> [1] > > > https://serverfault.com/questions/193114/linux-e1000e-intel-networking-driver-problems-galore-where-do-i-start > > > Thoughts anyone? > > Are you giving Linux enough time to work (no 100% RT domination of any core > > for > > hundreds of milliseconds or longer)? > I am not sure, yet. I have this logging function for reporting back to me > when I > loose samples. Loosing samples would currently make the software try to catch > up and this would mean 100% cpu till it does. I do see this being logged > around > the time it resets but I'm not sure if it's much worse than "usual". If for > some reason the hardware reset happens because linux gets starved I can easily > see this going cyclic. > Per Öberg So, I have managed to do some checking It looks like the cyclic resets are about 80-100 seconds apart. Before the first reset we are most likely holding the CPUs for about 3-4ms. I managed to get hold of a kernel message saying: [...] WARNING: CPU: 0 PID: 3 at net/sched/sch_generic.c:316 dev_watchdog+0x215/0x220 [...] NETDEV WATCHDOG: enp0s31f6 (e1000e): transmit queue 0 timed out The full trace is shown below. One difference that I have found is that I am running with "--cpu-affinity=2,3" when running manually, but not when using systemd to start the program. Can this have an impact? -------------------- DMESG TRACE ----------------------------------------- [31865.706967] ------------[ cut here ]------------ [31865.706973] WARNING: CPU: 0 PID: 3 at net/sched/sch_generic.c:316 dev_watchdog+0x215/0x220 [31865.706974] NETDEV WATCHDOG: enp0s31f6 (e1000e): transmit queue 0 timed out [31865.706974] Modules linked in: iTCO_wdt iTCO_vendor_support ppdev i915 intel_rapl intel_powerclamp coretemp kvm_intel kvm drm_kms_helper irqbypass crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel drm intel_gtt aesni_intel agpgart aes_x86_64 fb_sys_fops lrw gf128mul glue_helper e1000e ablk_helper syscopyarea cryptd sysfillrect sysimgblt efi_pstore igb xhci_pci psmouse xhci_hcd dca pcspkr i2c_algo_bit serio_raw ptp efivars pps_core xeno_can_peak_pci xeno_can_sja1000 xeno_can i2c_i801 shpchp i2c_smbus hci_uart btbcm btintel bluetooth parport_pc parport pinctrl_sunrisepoint pinctrl_intel i2c_hid tpm_tis tpm_tis_core tpm sch_fq_codel efivarfs ipv6 crc_ccitt [31865.707329] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.9.38-xenomai+ #6 [31865.707330] Hardware name: Default string Default string/SKYBAY, BIOS 5.11 09/22/2016 [31865.707331] I-pipe domain: Linux [31865.707333] ffffc90000033c80 ffffffff813e0324 ffffc90000033cd0 0000000000000000 [31865.707336] ffffc90000033cc0 ffffffff81054b67 0000013c6dc2eb00 0000000000000000 [31865.707517] ffff88026048fc80 0000000000000000 ffff88025ed74000 0000000000000001 [31865.707520] Call Trace: [31865.707524] [<ffffffff813e0324>] dump_stack+0x96/0xc2 [31865.707526] [<ffffffff81054b67>] __warn+0xc7/0xf0 [31865.707527] [<ffffffff81054bda>] warn_slowpath_fmt+0x4a/0x50 [31865.707529] [<ffffffff81a04be0>] ? dev_graft_qdisc+0x70/0x70 [31865.707568] [<ffffffff81a04df5>] dev_watchdog+0x215/0x220 [31865.707569] [<ffffffff81a04be0>] ? dev_graft_qdisc+0x70/0x70 [31865.707571] [<ffffffff81a04be0>] ? dev_graft_qdisc+0x70/0x70 [31865.707573] [<ffffffff810a6d47>] call_timer_fn.isra.25+0x17/0x70 [31865.707575] [<ffffffff810a6e47>] expire_timers+0xa7/0xd0 [31865.707576] [<ffffffff810a6eec>] run_timer_softirq+0x7c/0x160 [31865.707578] [<ffffffff81aae546>] ? _raw_spin_unlock_irq+0x16/0x30 [31865.707581] [<ffffffff810595b6>] __do_softirq+0xe6/0x1e0 [31865.707583] [<ffffffff810596e2>] run_ksoftirqd+0x32/0x40 [31865.707584] [<ffffffff81073ff5>] smpboot_thread_fn+0x165/0x230 [31865.707611] [<ffffffff81073e90>] ? sort_range+0x20/0x20 [31865.707827] [<ffffffff81070962>] kthread+0xd2/0xf0 [31865.707829] [<ffffffff81070890>] ? kthread_park+0x60/0x60 [31865.707831] [<ffffffff81aaed33>] ret_from_fork+0x23/0x30 [31865.707834] ---[ end trace 111a72a07d1d2f26 ]--- [31865.743096] e1000e 0000:00:1f.6 enp0s31f6: Reset adapter unexpectedly [31867.827820] e1000e: enp0s31f6 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx Per Öberg