>-----Original Message-----
>From: Prasanna Kannan <[email protected]>
>Sent: Monday, May 30, 2022 3:33 PM
>To: Chen, Hongzhan <[email protected]>; [email protected]
>Subject: AW: Difference between Xenomai timer and Linux clock
>
>> -----Ursprüngliche Nachricht-----
>> Von: Chen, Hongzhan [mailto:[email protected]]
>> Gesendet: Montag, 30. Mai 2022 02:56
>> An: Prasanna Kannan <[email protected]>;
>> [email protected]
>> Betreff: RE: Difference between Xenomai timer and Linux clock
>>
>>
>>
>> >-----Original Message-----
>> >From: Xenomai <[email protected]> On Behalf Of Prasanna
>> >Kannan via Xenomai
>> >Sent: Friday, May 27, 2022 9:39 PM
>> >To: [email protected]
>> >Subject: Difference between Xenomai timer and Linux clock
>> >
>> >Hello Everybody,
>> >
>> >I am comparing the Xenomai Timer(rt_timer_read()) and clock_gettime()
>> >with CLOCK_REALTIME and found that the two drift at roughly 100 us/s
>> >Here is the snippet from my code:
>> >
>> >init():
>> >clock_gettime(CLOCK_REALTIME, &ts_start); rtime_start =
>> >rt_timer_read();
>> >
>> >runtime():
>> >clk_xenotime = (rt_timer_read() - rtime_start) * 1e-9;
>> >clock_gettime(CLOCK_REALTIME, &ts); clk_rttime = (ts.tv_sec -
>> >ts_start.tv_sec) + (ts.tv_nsec -
>> >ts_start.tv_nsec) * 1e-9;
>> >delta = clk_rttime - clk_xenotime
>> >
>> >The observation is that the delta is around 100us/s ...
>> >ClockGetTime:2.588435s, rt_timer_read:2.588167s, delta:0.000268s
>> >ClockGetTime:3.588533s, rt_timer_read:3.588161s, delta:0.000372s
>> >ClockGetTime:4.588671s, rt_timer_read:4.588196s, delta:0.000475s ...
>> >
>> >The Linux clock is not corrected via NTP/PTP, thus I am wondering why
>> >they are drifting in this way.
>> >
>> >Some Information about my setup:
>> >Xenomai/cobalt v3.1
>> >Linux rtdonau 4.19.115-ipipe #54 SMP PREEMPT Wed Oct 13 12:16:56 CEST
>> >2021
>> >x86_64 GNU/Linux
>> >Kernel parameters: intel_idle.max_cstate=0 vga=0x317 ip=dhcp
>> >root=/dev/nfs
>> >nfsroot=10.0.0.1:/opt/xyz/xeno_rt,tcp,nfsvers=3 BOOT_IMAGE=xeno10.2
>> >I-pipe release #12 detected Cobalt core 3.1 detected
>> >Compiler: gcc version 7.5.0 (GCC)
>> >Build args: --prefix=/opt/xenomai-3.1 --enable-smp --enable-pshared
>> >--enable-dlopen-libs
>> >
>> >The hardware used is an Intel SBC based on Core i7-4700EQ CPU @ 2.40GHz
>>
>> One of what we found is that there is delayed work which would refine
>tsc
>> clock after Xenomai init and that cause Clock difference which may
>result in
>> such drift. The patchset "[Cobalt Xenoami3.1 PATCH 0/2] notify Xenomai
>> udpated clockfreq."
>> I sent in community at 5/27 try to fix what we found. Could you send
>your
>> complete linux dmsg to check if our issues is the same?
>>
>Yes, I can confirm this as I see similar messages in my linux dmesg:
>[ 0.000000] tsc: Detected 2394.479 MHz processor
>[ 1.714630] tsc: Refined TSC clocksource calibration: 2394.455 MHz
It seems there is similar refined tsc after xenomai init which is quite
different from what Xenomai is using
Could you do a quick test with passing xenomai.clockfreq=2394455000 in
commandline to force xenomai to use refined TSC clock freq
and then run your drift test again to check if there is improvement? If there
is improvement , I think my patchset may work.
Regards
Hongzhan Chen
>
>[rtdonau-~] !) cat /sys/module/xenomai/parameters/clockfreq
>2394479000
>Attached my complete dmesg.
>
>> Regards
>>
>> Hongzhan Chen
>> >
>> >Thank you in Advance.
>> >
>> >Best Regards
>> >Prasanna
>> >
