On Feb 8, 2005, at 7:05 PM, Chris Elmer wrote:
thanks Iain, i tried what you said, and altered the settings of the
XF86Config file to your suggestions, but it still didn't work. The
xserver did, however, send back an error report finally. and i was able
to see sorta what was going wrong (i think). it mentioned a working
configuration for the monitor could not be found, so i went back into
the Config file and changed the Vert Refresh to 60-75 (thinking, "isn't
this an average refresh rate for a monitor?") and kept the Horiz at your
values (40-60). i think changing the vert refresh rate values was a bad
thing to do. when i ran startx, it seemed like xwindow started up,
meaning the text prompt went away, and my computer ground away at
something, but nothing shows on the screen. it's completely blank.
now when i start up, it finishes booting, and then goes right to this
blank screen.
what did i do? should i just reinstall?
Iain McKee wrote:
<x-tad-bigger>I don't know if the same will work for you, but I had the same problem
on my g3 500 imac...no matter what, I could not start xserver.
I eventually figured out that I had to edit my XF86Config file with
nano (located /etc/X11/XF86Config)
Then I went to the part that says Vert Refresh and Horizontal and
changed the # value beside Vert to: 30.5-48.5
Hor to: 40-60
then save it with control-x and then at the root prompt, try
startx......then make sure to go into your display settings in the KDE
or GNOME GUI and ensure the correct monitor, etc. are selected
Give that a try and see if it works!!
On Feb 7, 2005, at 11:59 AM, Chris Elmer wrote:
></x-tad-bigger><x-tad-bigger> i'm trying to install ydl 4 on my quicksilver 733. i downloaded and
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> burned the iso's from the ftp site, and then booted from the first cd.
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> when i tried to run the graphical installer at the boot prompt, it
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> tried to start the install, but "exited abnormally" when it tried to
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> connect to X server.
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> so i just used install-safe, which seemed to work. but after
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> rebooting, xwindow could not be loaded, because of an error (sorry, i
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> don't remember what it was) that said said something to the effect of
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> it couldn't be loaded. then it presented me with a terminal where i
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> can only log in as root, since i was never presented with the "first
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> boot" set up, where i guess i add more users. any ideas?
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger>
</x-tad-bigger><x-tad-bigger>></x-tad-bigger><x-tad-bigger> -chris
</x-tad-bigger> _______________________________________________
yellowdog-newbie mailing list
[email protected]
http://lists.terrasoftsolutions.com/mailman/listinfo/yellowdog-newbie
_______________________________________________ yellowdog-newbie mailing list [email protected] http://lists.terrasoftsolutions.com/mailman/listinfo/yellowdog-newbie
