Hello, git clone git://git.yoctoproject.org/poky.git cd poky . oe-init-build-env MACHINE=beagleboard bitbake -v core-image-sato
Created 2 partitions on /dev/sdb fdisk /dev/sdb Welcome to fdisk (util-linux 2.21.1). Changes will remain in memory only, until you decide to write them. Be careful before using the write command. Command (m for help): p Disk /dev/sdb: 7960 MB, 7960788992 bytes 255 heads, 63 sectors/track, 967 cylinders, total 15548416 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 * 63 144584 72261 c W95 FAT32 (LBA) /dev/sdb2 144585 7132859 3494137+ 83 Linux format 2 partitions. mkfs.vfat -F 16 -n "boot" /dev/sdb1 mke2fs -j -L "rootfs" /dev/sdb2 remove the mmc /dev/sdb1 72098 0 72098 0% /run/media/vidal/boot /dev/sdb2 3441720 74096 3192920 3% /run/media/vidal/rootfs cd /home/vidal/poky/build/tmp/deploy/images cp MLO-beagleboard-1.5.0+git1+9f94c6577e3a018b6b75cbe39f32bb331871f915-r0 /run/media/vidal/boot/MLO cp u-boot-beagleboard-v2011.06+git5+b1af6f532e0d348b153d5c148369229d24af361a-r1.bin /run/media/vidal/boot/u-boot.bin cp uImage-3.0.32+git1+d282029891bba5440630a885b940dea5e34e3e2c_1+3ab688a78cac7b2e32afc83376a53370f2bd13b7-r4.0-beagleboard-20120712003552.bin /run/media/vidal/boot/uImage cd /run/media/vidal/rootfs tar jvxf /home/vidal/poky/build/tmp/deploy/images/core-image-sato-beagleboard-20120712003552.rootfs.tar.bz2 cp /home/vidal/uEnv.txt /run/media/vidal/boot cat /run/media/vidal/boot/uEnv.txt mpurate=auto dvimode="hd720 omapfb.vram=0:8M,1:4M,2:4M" vram=16M optargs="consoleblank=0" console="tty0 console=ttyO2,115200n8" umount /run/media/vidal/boot umount /run/media/vidal/rootfs sync * - * Qodem 0.1.2 Capture Generated Fri, 13 Jul 2012 10:51:17 -0600 BEGIN * - * Texas Instruments X-Loader 1.5.0 (Jul 11 2012 - 21:01:18) Beagle xM Reading boot sector Loading u-boot.bin from mmc U-Boot 2011.06 (Jul 11 2012 - 21:01:18) OMAP3630/3730-GP ES2.1, CPU-OPP2, L3-165MHz, Max CPU Clock 1 Ghz OMAP3 Beagle board + LPDDR/NAND I2C: ready DRAM: 512 MiB NAND: 0 MiB MMC: OMAP SD/MMC: 0 *** Warning - readenv() failed, using default environment In: serial Out: serial Err: serial Beagle unknown 0x02 No EEPROM on expansion board Die ID #158000029ff800000160a7450b02602d Hit any key to stop autoboot: 10 9 8 7 6 5 4 3 2 1 0 SD/MMC found on device 0 reading uEnv.txt 130 bytes read Importing environment from mmc ... reading uImage 3043164 bytes read Booting from mmc ... ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-3.0.32-yocto-standard Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3043100 Bytes = 2.9 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Linux version 3.0.32-yocto-standard (vi...@ws009.swbell.net<http://us.mc1814.mail.yahoo.com/mc/compose?to=vi...@ws009.swbell.net>) (gcc version 4.7.2 20120615 (prerelease) (GCC) ) #1 Wed Jul 11 20:38:46 MDT 2012 CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: OMAP3 Beagle Board Reserving 16777216 bytes SDRAM for VRAM Memory policy: ECC disabled, Data cache writeback OMAP3630 ES1.2 (l2cache iva sgx neon isp 192mhz_clk ) SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000 Clocking rate (Crystal/Core/MPU): 26.0/332/600 MHz Reprogramming SDRC clock to 332000000 Hz Built 1 zonelists in Zone order, mobility grouping on. Total pages: 125952 Kernel command line: console=tty0 console=ttyO2,115200n8 mpurate=auto vram=16M o mapfb.mode=dvi:hd720 omapfb.vram=0:8M,1:4M,2:4M omapfb.debug=y omapdss.def_disp= dvi root=/dev/mmcblk0p2 rw rootfstype=ext3 rootwait PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) allocated 2097152 bytes of page_cgroup please try 'cgroup_disable=memory' option if you don't want memory cgroups Memory: 496MB = 496MB total Memory: 494448k/494448k available, 29840k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffc00000 - 0xffe00000 ( 2 MB) vmalloc : 0xe0800000 - 0xf8000000 ( 376 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0058000 ( 320 kB) .text : 0xc0058000 - 0xc0613b0c (5871 kB) .data : 0xc0614000 - 0xc0671438 ( 374 kB) .bss : 0xc067145c - 0xc06b5044 ( 271 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:410 IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrupts Total of 96 interrupts on 1 active controller omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck. OMAP clockevent source: GPTIMER12 at 32768 Hz sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms Console: colour dummy device 80x30 console [tty0] enabled Calibrating delay loop... 500.97 BogoMIPS (lpj=1953792) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 Initializing cgroup subsys debug Initializing cgroup subsys cpuacct Initializing cgroup subsys memory Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys blkio CPU: Testing write buffer coherency: ok ftrace: allocating 18007 entries in 53 pages devtmpfs: initialized omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup omap_hwmod: i2c1: softreset failed (waited 10000 usec) omap_hwmod: i2c2: softreset failed (waited 10000 usec) omap_hwmod: i2c3: softreset failed (waited 10000 usec) print_constraints: dummy: NET: Registered protocol family 16 GPMC revision 5.0 omap_device: omap_gpio.0: new worst case activate latency 0: 30517 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 OMAP GPIO hardware version 2.5 omap_mux_init: Add partition: #1: core, flags: 0 OMAP3 Beagle Rev: unknown 2 omap_device: omap_uart.1: new worst case deactivate latency 0: 30517 Found NAND on CS0 Registering NAND on CS0 Unable to get DVI reset GPIO OMAP DMA hardware revision 5.0 bio: create slab <bio-0> at 0 SCSI subsystem initialized omap_device: omap2_mcspi.1: new worst case activate latency 0: 30517 omap_device: omap2_mcspi.1: new worst case deactivate latency 0: 30517 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb omap_i2c omap_i2c.1: bus 1 rev4.0 at 2600 kHz twl4030: PIH (irq 7) chaining IRQs 368..375 twl4030: power (irq 373) chaining IRQs 376..383 twl4030: gpio (irq 368) chaining IRQs 384..401 print_constraints: VUSB1V5: 1500 mV normal standby print_constraints: VUSB1V8: 1800 mV normal standby print_constraints: VUSB3V1: 3100 mV normal standby twl4030_usb twl4030_usb: Initialized TWL4030 USB module print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby print_constraints: VDAC: 1800 mV normal standby print_constraints: VDVI: 1800 mV normal standby print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV normal standby omap_device: omap_i2c.1: new worst case deactivate latency 0: 30517 omap_device: omap_i2c.3: new worst case activate latency 0: 30517 omap_i2c omap_i2c.3: bus 3 rev4.0 at 100 kHz Advanced Linux Sound Architecture Driver Version 1.0.24. cfg80211: Calling CRDA to update world regulatory domain Switching to clocksource 32k_counter Switched to NOHz mode on CPU #0 musb-hdrc: version 6.0, musb-dma, otg (peripheral+host) omap_device: musb-omap2430.-1: new worst case activate latency 0: 30517 musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 965 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) OMAP DSS rev 2.0 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0 omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1 omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2 console [ttyO2] enabled omap_uart.3: ttyO3 at MMIO 0x49042000 (irq = 80) is a OMAP UART3 brd: module loaded omap2-nand driver initializing No NAND device found. No NAND device found. usbcore: registered new interface driver kaweth pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver usbcore: registered new interface driver pegasus usbcore: registered new interface driver asix usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver dm9601 usbcore: registered new interface driver smsc75xx usbcore: registered new interface driver smsc95xx usbcore: registered new interface driver net1080 usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus usbcore: registered new interface driver MOSCHIP usb-ethernet driver usbcore: registered new interface driver int51x1 cdc_ncm: 04-Aug-2011 usbcore: registered new interface driver cdc_ncm console [netcon0] enabled netconsole: network logging started ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver _regulator_get: ehci-omap.0 supply hsusb0 not found, using dummy regulator _regulator_get: ehci-omap.0 supply hsusb1 not found, using dummy regulator ehci-omap ehci-omap.0: OMAP-EHCI Host Controller ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mousedev: PS/2 mouse device common for all mice twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 twl_rtc twl_rtc: Power up reset detected. twl_rtc twl_rtc: Enabling TWL-RTC. omap_device: omap_wdt.-1: new worst case activate latency 0: 30517 OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec omap_device: omap_wdt.-1: new worst case deactivate latency 0: 30517 cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver usbhid usbhid: USB HID core driver OMAP3 Beagle/Devkit8000 SoC init asoc: twl4030-hifi <-> omap-mcbsp-dai.1 mapping ok ALSA device list: #0: omap3beagle TCP cubic registered NET: Registered protocol family 17 Registering the dns_resolver key type VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 ThumbEE CPU extension supported. sr_init: No PMIC hook to init smartreflex smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized SmartReflex Class3 initialized clock: disabling unused clocks to save power registered taskstats version 1 Console: switching to colour frame buffer device 80x25 regulator_init_complete: VDAC: incomplete constraints, leaving on twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) Waiting for root device /dev/mmcblk0p2... mmc0: new SDHC card at address 1234 mmcblk0: mmc0:1234 SA08G 7.41 GiB (ro) mmcblk0: p1 p2 VFS: Cannot open root device "mmcblk0p2" or unknown-block(179,2) Please append a correct "root=" boot option; here are the available partitions: b300 7774208 mmcblk0 driver: mmcblk b301 72261 mmcblk0p1 00000000-0000-0000-0000-000000000000 b302 3494137 mmcblk0p2 00000000-0000-0000-0000-000000000000 VFS: Unable to mount root fs on unknown-block(179,2) User configuration error - no valid root filesystem found Kernel panic - not syncing: Invalid configuration from end user prevents continu ing [<c0063d00>] (unwind_backtrace+0x0/0xec) from [<c044baa0>] (dump_stack+0x20/0x24 ) [<c044baa0>] (dump_stack+0x20/0x24) from [<c044bcb0>] (panic+0x64/0x184) [<c044bcb0>] (panic+0x64/0x184) from [<c0008eb4>] (mount_block_root+0x1e4/0x230) [<c0008eb4>] (mount_block_root+0x1e4/0x230) from [<c00090e0>] (mount_root+0xf8/0 x11c) [<c00090e0>] (mount_root+0xf8/0x11c) from [<c0009270>] (prepare_namespace+0x16c/ 0x1cc) [<c0009270>] (prepare_namespace+0x16c/0x1cc) from [<c0008ab0>] (kernel_init+0x12 c/0x160) [<c0008ab0>] (kernel_init+0x12c/0x160) from [<c005e86c>] (kernel_thread_exit+0x0 /0x8) * - * Qodem 0.1.2 Capture Generated Fri, 13 Jul 2012 10:51:55 -0600 END * - * I created a serial-boot.cmd setenv bootcmd 'mmc init; fatload mmc 0:1 0x80300000 uImage; bootm 0x80300000' setenv bootargs 'console=tty0 console=ttyO2,115200n8 root=/dev/mmcblk0p2 rootwait rootfstype=ext3 ro' boot Any help will be appreciated. Regards
_______________________________________________ yocto mailing list yocto@yoctoproject.org https://lists.yoctoproject.org/listinfo/yocto