On Mon, Apr 14, 2014 at 04:25:55AM -0600, Gary Thomas wrote: > On 2014-04-13 20:33, Denys Dmytriyenko wrote: > > On Sun, Apr 13, 2014 at 03:12:16AM -0600, Gary Thomas wrote: > >> I just tried building (core-image-sato) for my BeagleBoneBlack > >> using the latest Poky/Yocto master: > >> > >> Build Configuration: > >> BB_VERSION = "1.23.0" > >> BUILD_SYS = "i686-linux" > >> NATIVELSBSTRING = "Fedora-13" > >> TARGET_SYS = "arm-poky-linux-gnueabi" > >> MACHINE = "beaglebone" > >> DISTRO = "poky" > >> DISTRO_VERSION = "1.6+snapshot-20140411" > >> TUNE_FEATURES = "armv7a vfp neon callconvention-hard cortexa8" > >> TARGET_FPU = "vfp-neon" > >> meta > >> meta-yocto > >> meta-yocto-bsp = "master:863cc7483f5ee43189537940de8ee5c0964d24cc" > >> > >> This built the kernel using SRCREV 928d7b2dda > >> > >> I followed the bring-up instructions from README.hadware and the > >> boot failed to even start the kernel. Here's what I see: > >> > >> =============================== boot log > >> ========================================= > >> U-Boot 2013.07 (Apr 11 2014 - 15:03:04) > >> > >> I2C: ready > >> DRAM: 512 MiB > >> WARNING: Caches not enabled > >> NAND: 0 MiB > >> MMC: OMAP SD/MMC: 0, OMAP SD/MMC: 1 > >> *** Warning - readenv() failed, using default environment > >> > >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, > >> SoftConn) > >> musb-hdrc: MHDRC RTL version 2.0 > >> musb-hdrc: setup fifo_mode 4 > >> musb-hdrc: 28/31 max ep, 16384/16384 memory > >> USB Peripheral mode controller at 47401000 using PIO, IRQ 0 > >> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, > >> SoftConn) > >> musb-hdrc: MHDRC RTL version 2.0 > >> musb-hdrc: setup fifo_mode 4 > >> musb-hdrc: 28/31 max ep, 16384/16384 memory > >> USB Host mode controller at 47401800 using PIO, IRQ 0 > >> Net: <ethaddr> not set. Validating first E-fuse MAC > >> Phy not found > >> PHY reset timed out > >> cpsw, usb_ether > >> Hit any key to stop autoboot: 0 > >> mmc0 is current device > >> SD/MMC found on device 0 > >> reading uEnv.txt > >> ** Unable to read file uEnv.txt ** > >> 4981688 bytes read in 613 ms (7.7 MiB/s) > >> 29192 bytes read in 46 ms (619.1 KiB/s) > >> Booting from mmc ... > >> ## Booting kernel from Legacy Image at 80200000 ... > >> Image Name: Linux-3.14.0-yocto-standard > >> Image Type: ARM Linux Kernel Image (uncompressed) > >> Data Size: 4981624 Bytes = 4.8 MiB > >> Load Address: 80008000 > >> Entry Point: 80008000 > >> Verifying Checksum ... OK > >> ## Flattened Device Tree blob at 80f80000 > >> Booting using the fdt blob at 0x80f80000 > >> Loading Kernel Image ... OK > >> Using Device Tree in place at 80f80000, end 80f8a207 > >> > >> Starting kernel ... > >> ================================================================================== > >> > >> Any ideas what I've done wrong? > > > > Hmm, everything looks sane. What revision is your BBB? And did you press > > USER/BOOT button or erased eMMC partition per instructions? > > > > Revision A5A, with an LCD cape
Hmm, I'm wondering if LCD cape conflicts here - there's no cape support in this BSP. Can you try w/o it? As of the board revision - I was testing on different ones from A1 to A6 and didn't see any major issue... -- Denys -- _______________________________________________ yocto mailing list yocto@yoctoproject.org https://lists.yoctoproject.org/listinfo/yocto
