Hello!
I am completely clueless, but after a wee kstrugling around i can not
connect to my access point, which is a belkin pre-n.
I use the Zydas ZyAir 220-G stick. Under Windiws everything is fine.
I use Ubuntu Dapper Drake, Kernel is 2.6.15-25 PREEMPT i686
I did modprobe -r zd1211 and build the latest available version of the
driver r80.
make
make install
Successfully did depmod -a and modprobe -v zd1211
Thats what dmesg says:
[17181098.376000] usb 1-1: new full speed USB device using uhci_hcd and
address 2
[17181098.628000] usb 1-1: reset full speed USB device using uhci_hcd
and address 2
[17181098.764000] Release Ver = 4330
[17181098.764000] zd1211:bulk out: wMaxPacketSize = 40
[17181098.764000] zd1211:bulk in: wMaxPacketSize = 40
[17181098.764000] zd1211:interrupt in: wMaxPacketSize = 40
[17181098.764000] zd1211:interrupt in: int_interval = 1
[17181098.764000] zd1211:bulk out: wMaxPacketSize = 40
[17181098.764000] EEPORM Ver = 4330
[17181098.776000] zd1211:USB Download Boot code success
[17181098.788000] zd1211:MAC address = 00:13:49:00:55:9c
[17181098.792000] zd1211:AddrEntryTable = f7d4
[17181098.796000] zd1211:RF_Mode = 0000000d
[17181098.796000] PA type: 0
[17181098.796000] RFMD RF
[17181098.796000] zd1211:Pure B-Mode
[17181099.012000] zd1211:AllowedChannel = 000007ff
[17181099.016000] zd1211:LinkLEDn = 200
[17181099.020000] AllowedChannel = 000107ff
[17181099.020000] Region:48
[17181099.340000] uhci_hcd 0000:00:11.3: Controller not stopped yet!
[17181099.452000] zd1205: (exit) zd1205_config,
/home/john/install/zd1211-driver-r80/src/zd1205.c line 2601
[17181099.452000] zd1205: (exit) zd1205_init,
/home/john/install/zd1211-driver-r80/src/zd1205.c line 8569
[17181099.716000] zd1205: (enter) zd1205_open,
/home/john/install/zd1211-driver-r80/src/zd1205.c line 4352
[17181099.792000] zd1205: (exit) zd1205_open,
/home/john/install/zd1211-driver-r80/src/zd1205.c line 4435
[17181099.792000] ADDRCONF(NETDEV_UP): wlan0: link is not ready
My interfaces:
auto lo
iface lo inet loopback
auto eth0
iface eth0 inet dhcp
auto eth1
iface eth1 inet dhcp
auto eth2
iface eth2 inet dhcp
auto ath0
iface ath0 inet dhcp
auto wlan0
iface wlan0 inet dhcp
Output of iwlist scan:
wlan0 Scan completed :
Cell 01 - Address: 00:11:50:23:B1:ED
ESSID:"Prometheus"
Mode:Master
Frequency:2.437 GHz (Channel 6)
Extra:SignalStrength=41%,LinkQuality:8%
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Please note, that both SignalStrength and LinkQuality change a lot, and
are very often at nearly 100% --- for testing purpose i sit very close
to the AP!
Output of iwconfig:
wlan0 802.11b/g NIC ESSID:"Prometheus"
Mode:Managed Frequency=2.462 GHz Access Point:
Not-Associated
Bit Rate:1 Mb/s
Retry:off RTS thr=2432 B Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=100/100 Signal level=36/100 Noise level=0/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:378
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
When i connect the stick i get a wlan0 - interface, but when i do
iwconfig wlan0 essid <Here> or even iwconfig wlan0 ap x:y:z i never get
associated with my access point. Whats wrong? Please help me, i am
really desperate now!
I have already disabled encryption
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_______________________________________________
Zd1211-devs mailing list - http://zd1211.ath.cx/
Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs