Thanks for clearing that up Daniel. I have installed rw but after trying and failing with ndiswrapper, though obviously not totally. I had the suspicion from start log that this was the case. I will try to uninstall the other driver and re-configure with zd1211rw. cheers.
ash wrote: > > I don't know if this is a problem with the driver or configuration. > Connect fine, most of the time, but end up with dropped connection with > any load on it, If i do ifdown then ifup it shows no ap and the only way > to reconnect is rebooting. > > This is the info from startup log that seems relevant if anybody can point > me in a direction to try and sort this out. > > cheers > Ash > > <6>usb 5-4: new device found, idVendor=07b8, idProduct=6001 > <6>usb 5-4: new device strings: Mfr=16, Product=32, SerialNumber=0 > <6>usb 5-4: Product: USB2.0 WLAN > <6>usb 5-4: Manufacturer: ZyDAS > <6>usb 5-4: configuration #1 chosen from 1 choice > <6>saa7133[0]: i2c eeprom 00: 68 51 14 02 10 28 ff ff ff ff ff ff ff ff ff > ff > <6>saa7133[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > ff > <6>saa7133[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > ff > <6>saa7133[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > ff > <6>saa7133[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > ff > <6>saa7133[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > ff > <6>saa7133[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > ff > <6>saa7133[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff > ff > <6>tuner 1-004b: chip found @ 0x96 (saa7133[0]) > <6>tuner 1-004b: setting tuner address to 61 > <6>tuner 1-004b: tuner: type set to tda8290+75 > 4>zd1211: module not supported by Novell, setting U taint flag. > <5>zd1211 - http://zd1211.ath.cx/ - r83 > <5>Based on www.zydas.com.tw driver version 2.5.0.0 > <7>zd1211:bulk out: wMaxPacketSize = 200 > <7>zd1211:bulk in: wMaxPacketSize = 200 > <7>zd1211:interrupt in: wMaxPacketSize = 40 > <7>zd1211:interrupt in: int_interval = 1 > <7>zd1211:bulk out: wMaxPacketSize = 40 > <5>EEPORM Ver = 4330 > <7>zd1211:USB Download Boot code success > <7>zd1211:MAC address = 00:e0:98:e7:7b:8f > <7>zd1211:AddrEntryTable = f7d4 > <7>zd1211:RF_Mode = 0000010d > <3>PA type: 0 > <4>RFMD RF > <7>zd1211:Mixed Mode > <7>zd1211:AllowedChannel = 000007ff > <7>zd1211:LinkLEDn = 200 > <4>AllowedChannel = 000107ff > <4>Region:64 > <7>zd1205: (exit) zd1205_config, > /home/ashley/bin/zd1211-driver-r83/src/zd1205.c line 2601 > <7>zd1205: (exit) zd1205_init, > /home/ashley/bin/zd1211-driver-r83/src/zd1205.c line 8570 > <6>usbcore: registered new driver zd1211 > <6>usbcore: registered new driver hiddev > unusedwlan0 -o rc onboot > HWDESC = wlan0 CONFIG = wlan-bus-usb INTERFACE = wlan0 > > wlan0 > wlan0 configuration: wlan-bus-usb > wlan-bus-usb wlan0 -o rc onboot > unknown option rc ignored > prefer wpa_supplicant: no > configuration requires wpa_supplicant > wlan0 warning: WPA configured but may be unsupported > wlan0 warning: by this device > using WPA driver 'wext' for interface wlan0 > wlan0 starting wpa_supplicant > wlan-bus-usb wlan0 -o rc onboot > Starting service dhcp client on wlan0 > wlan0 (DHCP) . . . . . no IP address yet... backgrounding. > wlan0 IP address: 192.168.1.1/24 > Handling Index <>: > IPADDR = 192.168.1.1 > PREFIXLEN = 24 > CHECK_DUPLICATE_IP = no > wlan-bus-usb wlan0 -o rc onboot > calling: ip route replace to default via 192.168.1.1 ---> OK > calling: ip route replace to 169.254.0.0/16 dev wlan0 ---> OK > wlan0 returned 12 > waiting > ... still waiting for hotplug devices: > SUCCESS_IFACES= lo > MANDATORY_DEVICES= __NSC__ > ... final > SUCCESS_IFACES= lo > MANDATORY_DEVICES= > FAILED=0 > noiface -o rc onboot > Setting up service network . . . . . . . . . . . . . . . > .done > -- View this message in context: http://www.nabble.com/zd1211rw-on-2.6.16.13-kernel-tf2677509.html#a7477493 Sent from the zd1211-devs mailing list archive at Nabble.com. ------------------------------------------------------------------------- Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV _______________________________________________ Zd1211-devs mailing list - http://zd1211.ath.cx/ Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
