I think vmware requires the same config as Hyper-v : enabled MAC Spoofing. (and
optionally assign static mac).
Once it's enabled it should work like a charm.
It's a common issue for hyper-v and vmware hypervisors.
Regards,
Marco
CEO at Key4ce
------------------------------------------------------------
Phone NL: +31 (0)40 290 3310
Phone EN: +44 (0)1332 898 999
Phone CN: +86 (0)7552 8245 985
Italielaan 9
5632 TA
Eindhoven
------------------------------------------------------------
http://www.key4ce.eu<http://www.key4ce.eu/>
Van: Karelis, E. Pete [mailto:[email protected]]
Verzonden: zondag 10 november 2013 04:08
Aan: [email protected]
Onderwerp: Re: [Zenloadbalancer-support] cluster mess
Running on VMware? This is indicative of CARP packets not making it between
nodes. CARP uses multicast Ethernet frames, and some switches won't forward
them without an IGMP message (since usually layer 3 multicast is mapped to a
layer 2 multicast frame). You need to get the CARP packets working, then you
are set.
We use the Nexus 1000v distributed virtual switch on VMware, and it was a few
commands on the port-profile to enable CARP multicast forwarding.
Let me know what your networking looks like, and I'll see what I can do to help
you.
From: Marco Accardo [mailto:[email protected]]
Sent: Saturday, November 09, 2013 2:41 PM
To: [email protected]
Subject: [Zenloadbalancer-support] cluster mess
Well I have a real mess with my zlb cluster
At a certain point before I realized the problem I now have a two node cluster
where both nodes think they are master and they masters...status shows
Zen latency is UP on Gue-Debian-ExBalancer2 10.10.4.86 | Zen latency is UP on
Gue-Debian-ExBalancer1 10.10.4.85
Cluster IP 10.10.4.87 is active on Gue-Debian-ExBalancer2 Cluster is active on
Gue-Debian-ExBalancer1 !
Zen Inotify is running on Gue-Debian-ExBalancer2 Gue-Debian-ExBalancer1 !
Global status: !
all services are always on for both nodes..
I can both nodeshave a active VIP x.x.x.87.
I have tried disabling the cluster and redoing the config and it always ends up
with the same status...
I have gone to into a one of the nodes into /zenloadbalncer/config diretcory
and removed all files and recreated the cluster and it still ends up the same
way...
Is there a specific set of files I need to get the system back to the point say
1 node with all my farms defined no cluster and a second unconfigured node that
will let me run through the cluster configuration wizard.
I would like to remove all cluster information and start from scratch without a
reinstall.
Any help would be appreciated...
Marco
RWDI - One of Canada's 50 Best Managed Companies This communication is intended
for the sole use of the party to whom it was addressed and may contain
information that is privileged and/or confidential. Any other distribution,
copying or disclosure is strictly prohibited. If you received this email in
error, please notify us immediately by replying to this email and delete the
message without retaining any hard or electronic copies of same. Outgoing
emails are scanned for viruses, but no warranty is made to their absence in
this email or attachments.
**********************************************************************
U.S. Treasury Circular 230 Notice: Any tax advice contained in this
communication
(including any attachments) was not intended or written to be used,
and cannot be used, for the purpose of (a) avoiding penalties that may be
imposed under the Internal Revenue
Code or by any other applicable tax authority; or (b) promoting, marketing or
recommending to another party any tax-related matter addressed herein. We
provide this
disclosure on all outbound e-mails to assure compliance with new standards of
professional practice, pursuant to which certain tax advice must satisfy
requirements as to
form and substance.
************************************************************************
************************************************************************
This electronic mail transmission may contain confidential or privileged
information. If
you believe you have received this message in error, please notify the sender
by reply
transmission and delete the message without copying or disclosing it.
************************************************************************
------------------------------------------------------------------------------
November Webinars for C, C++, Fortran Developers
Accelerate application performance with scalable programming models. Explore
techniques for threading, error checking, porting, and tuning. Get the most
from the latest Intel processors and coprocessors. See abstracts and register
http://pubads.g.doubleclick.net/gampad/clk?id=60136231&iu=/4140/ostg.clktrk
_______________________________________________
Zenloadbalancer-support mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/zenloadbalancer-support
