install smartmontools
There is no package for it but it's EASY to install once you do, you can get ouput like this: pfexec /usr/local/sbin/smartctl -d sat,12 -a /dev/rdsk/c5t0d0 smartctl 5.39.1 2010-01-28 r3054 [i386-pc-solaris2.11] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.12 family Device Model: ST31000528AS Serial Number: 6VP06FF5 Firmware Version: CC34 User Capacity: 1,000,204,886,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Sat May 22 11:15:50 2010 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 192) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 113 099 006 Pre-fail Always - 55212722 3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 132 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1 7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 136183285 9 Power_On_Hours 0x0032 091 091 000 Old_age Always - 7886 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 132 183 Runtime_Bad_Block 0x0000 100 100 000 Old_age Offline - 0 184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 085 085 000 Old_age Always - 15 190 Airflow_Temperature_Cel 0x0022 063 054 045 Old_age Always - 37 (Lifetime Min/Max 32/40) 194 Temperature_Celsius 0x0022 037 046 000 Old_age Always - 37 (0 16 0 0) 195 Hardware_ECC_Recovered 0x001a 048 025 000 Old_age Always - 55212722 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 23691039612915 241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 263672243 242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 960644151 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. On Sat, May 22, 2010 at 3:09 AM, Andreas Iannou < andreas_wants_the_w...@hotmail.com> wrote: > I should mention that iostat -En doesn't return any information. Is there > a reliable way of reading SMART information natively in OpenSolaris? > > Cheers, > Andre > > ------------------------------ > From: andreas_wants_the_w...@hotmail.com > To: zfs-discuss@opensolaris.org > Date: Sat, 22 May 2010 16:49:15 +1000 > Subject: [zfs-discuss] HDD Serial numbers for ZFS > > > Hallo again, > > I'm wondering how one would get the serial numbers for a HDD to identify > them via OpenSolaris and match them to the ZFS pool. > > Like I'm trying to workout which HDD c7t3d0 reliably. Can serial numbers be > read by OpenSolaris? > > Cheers, > Andre > > ------------------------------ > Looking for a hot date? View photos of singles in your > area!<http://clk.atdmt.com/NMN/go/150855801/direct/01/> > ------------------------------ > Meet local singles online. Browse profiles for > FREE!<http://clk.atdmt.com/NMN/go/150855801/direct/01/> > > _______________________________________________ > zfs-discuss mailing list > zfs-discuss@opensolaris.org > http://mail.opensolaris.org/mailman/listinfo/zfs-discuss > >
_______________________________________________ zfs-discuss mailing list zfs-discuss@opensolaris.org http://mail.opensolaris.org/mailman/listinfo/zfs-discuss
