Yes, I had created the zone with the same ip as the global-zone. I have submitted a request for 2 additional ip addresses for the zones. Thanks.
Jeff Victor wrote: > Lana Tom wrote: > >> Hi - >> >> I'm trying to boot a zone that I've created but I'm getting interface >> errors. >> Any ideas why the zone will not boot? >> >> xc12p11-b1# zoneadm list -cv >> ID NAME STATUS PATH >> BRAND IP >> 0 global running / native >> shared >> - xc12p11-b1 installed /export/xc12p11-b1 native >> shared >> >> xc12p11-b1# zoneadm -z xc12p11-b1 ready >> zoneadm: zone 'xc12p11-b1': ce0:1: could not bring network interface >> up: address in use by zone 'global': Cannot assign requested address >> zoneadm: zone 'xc12p11-b1': call to zoneadmd failed >> >> xc12p11-b1# zoneadm -z xc12p11-b1 boot >> zoneadm: zone 'xc12p11-b1': ce0:1: could not bring network interface >> up: address in use by zone 'global': Cannot assign requested address > > The message above is telling you that the zone was configured with the > same IP address as the global zone. What IP address did you assign to > the zone? It cannot be the same as an address used by the global zone. > >> zoneadm: zone 'xc12p11-b1': call to zoneadmd failed >> >> >> xc12p11-b1# ifconfig -a >> lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu >> 8232 index 1 >> inet 127.0.0.1 netmask ff000000 >> ce0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 >> inet 10.1.75.29 netmask fffff800 broadcast 10.1.79.255 >> ether 0:3:ba:1f:e2:57 >> dman0: flags=1008843<UP,BROADCAST,RUNNING,MULTICAST,PRIVATE,IPv4> mtu >> 1500 index 3 >> inet 192.168.103.3 netmask ffffffe0 broadcast 192.168.103.31 >> ether 0:3:ba:1f:e2:57 >> e1000g0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 4 >> inet 80.60.70.2 netmask ff000000 broadcast 80.255.255.255 >> ether 0:3:ba:1f:e2:57 >> e1000g1: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5 >> inet 80.60.71.2 netmask ff000000 broadcast 80.255.255.255 >> ether 0:3:ba:1f:e2:57 >> >> xc12p11-b1# cat /etc/path_to_inst | grep ce >> "/[EMAIL PROTECTED],600000/[EMAIL PROTECTED]/[EMAIL PROTECTED]" 0 "ce" >> "/[EMAIL PROTECTED],600000/[EMAIL PROTECTED]/[EMAIL PROTECTED]" 1 "ce" >> >> xc12p11-b1# cat /etc/path_to_inst | grep dman >> >> xc12p11-b1# cat /etc/path_to_inst | grep e1000 >> "/[EMAIL PROTECTED],700000/[EMAIL PROTECTED]" 0 "e1000g" >> "/[EMAIL PROTECTED],700000/[EMAIL PROTECTED],1" 1 "e1000g" >> >> xc12p11-b1# cat /etc/path_to_inst | grep lo0 >> >> xc12p11-b1# uname -a >> SunOS xc12p11-b1 5.10 Generic_120011-14 sun4u sparc SUNW,Sun-Fire-15000 >> xc12p11-b1# cat /etc/release >> Solaris 10 8/07 s10s_u4wos_12b SPARC >> Copyright 2007 Sun Microsystems, Inc. All Rights Reserved. >> Use is subject to license terms. >> Assembled 16 August 2007 >> Also, does the name of the zone(s) need to be unique or can they be >> the same as the machine name xc12p11-b1? I am using xc12p11-b1 >> and would like to create two exclusive zones inside a global-zone >> so I can run some tests between the two zones. >> >> Any help is appreciated. >> Thanks, >> -Lana >> >> >> >> >> >> >> _______________________________________________ zones-discuss mailing list zones-discuss@opensolaris.org
