Hi Giles, As I mentioned before, very probably your scanner cannot be used via Ethernet and WiFi. Please retry scanning via USB connection. Then you should remove the Ethernet cable and/or disable WiFi.
Hope this helps. Cheers, Rolf Am 12.09.2018 um 23:21 schrieb Giles Knap: > Thanks Rolf, > > I was immediately able to see the scanner but unfortunately when I try > to scan I get an error. I have tried power cycling the scanner and > restarting ubuntu but get the following:- > > Thanks, > giles. > -------------------------------- > giles@gklinux:~$ SANE_DEBUG_PIXMA=21 SANE_DEBUG_BJNP=3 simple-scan > > (simple-scan:15292): Gtk-WARNING **: 22:19:23.217: Failed to register > client: GDBus.Error:org.gnome.SessionManager.AlreadyRegistered: Unable > to register client > [sanei_debug] Setting debug level of pixma to 21. > [pixma] pixma is compiled with pthread support. > [pixma] pixma version 0.17.50 > [sanei_debug] Setting debug level of bjnp to 3. > [pixma] pixma_collect_devices() found Canon PIXMA TS6100 Series at > libusb:002:005 > [bjnp] sanei_bjnp_find_devices, pixma backend version: 0.17.50 > [bjnp] sanei_bjnp_find_devices: No devices specified in configuration file. > [bjnp] sanei_bjnp_find_devices: Added all configured scanners, now do > auto detection... > [bjnp] prepare_socket: lo is not a valid IPv4 interface, skipping... > [bjnp] prepare_socket: eno1 is IPv4 capable, sending broadcast, socket = 23 > [bjnp] prepare_socket: lo is not a valid IPv6 interface, skipping... > [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 24 > [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 25 > [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 26 > [bjnp] sanei_find_devices: scanner discovery finished... > [pixma] pixma_find_scanners() found 1 devices > [pixma] pixma_collect_devices() found Canon PIXMA TS6100 Series at > libusb:002:005 > [bjnp] sanei_bjnp_find_devices, pixma backend version: 0.17.50 > [bjnp] sanei_bjnp_find_devices: No devices specified in configuration file. > [bjnp] sanei_bjnp_find_devices: Added all configured scanners, now do > auto detection... > [bjnp] prepare_socket: lo is not a valid IPv4 interface, skipping... > [bjnp] prepare_socket: eno1 is IPv4 capable, sending broadcast, socket = 23 > [bjnp] prepare_socket: lo is not a valid IPv6 interface, skipping... > [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 24 > [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 25 > [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, socket = 26 > [bjnp] sanei_find_devices: scanner discovery finished... > [pixma] pixma_open(): Canon PIXMA TS6100 Series > [pixma] pixma_connect() failed EBUSY > [pixma] pixma_open() failed EBUSY > [pixma] pixma_close(): Canon PIXMA TS6100 Series > > > On Wed, Sep 12, 2018 at 9:14 PM Rolf Bensch <r...@bensch-online.de > <mailto:r...@bensch-online.de>> wrote: > > Hi Giles, > > I just added your scanner to SANE. You can pull the recent version from > git now. > > Or you can use my Ubuntu PPA: > https://launchpad.net/~rolfbensch/+archive/ubuntu/sane-git > <https://launchpad.net/%7Erolfbensch/+archive/ubuntu/sane-git> . > Then you > must wait for the next version tomorrow. > > Please report your results. > > Cheers, > Rolf > > Am 12.09.2018 um 20:40 schrieb Giles Knap: > > Many thanks, Rolf. > > > > I would be very happy to have my scanner working via USB. > > > > The USB IDs are as follows:- > > Bus 002 Device 005: ID 04a9:1822 Canon, Inc. > > > > Cheers, > > giles > > > > On Wed, Sep 12, 2018 at 6:41 PM Rolf Bensch <r...@bensch-online.de > <mailto:r...@bensch-online.de> > > <mailto:r...@bensch-online.de <mailto:r...@bensch-online.de>>> wrote: > > > > Hi Giles, > > > > I'm sorry to tell you that your scanner isn't supported by > SANE. You > > confuse your TS6150 with the TS6050 (PIXMA TS6000 Series). > > > > There's another problem with the tested TSxxxx scanners: WiFi > isn't > > working. > > > > I can quickly implement your scanner to SANE, but you very > probably > > need to use the scanner USB connected to your PC. Please send me > > your scanner's USB IDs, which can be indentified on a console > with: > > $ lsusb > > Bus 002 Device 007: ID 04a9:1908 Canon, Inc. > > ... > > > > Hope this helps. > > > > Cheers, > > Rolf > > > > > > Am 03.09.2018 um 18:30 schrieb Giles Knap: > >> Hello, > >> > >> I'm testing the latest pixma support against the TS6150 which is > >> listed as not yet tested. > >> > >> I can't connect over USB or TCP even if I explicitly place my > >> device's IP address in /etc/sane.d/pixma.conf as follows:- > >> > >> bjnp-timeout=5000 > >> bjnp://192.168.0.100:8612 <http://192.168.0.100:8612> > <http://192.168.0.100:8612> > >> > >> I am running on Ubuntu 18.04.1 and have built from the latest > >> source in master branch > of https://gitlab.com/sane-project/backends. > >> > >> The compilation is with debug and I get the following output > >> pasted below. > >> > >> The device is working since I am able to scan in an incredibly > >> limited fashion using the official scangearmp2 (which I have > since > >> uninstalled). The device also works if I reboot to windows. > >> > >> ---------------------------------------------- > >> giles@gklinux:~/github/backends$ SANE_DEBUG_PIXMA=21 > >> SANE_DEBUG_BJNP=3 simple-scan > >> > >> (simple-scan:15264): Gtk-WARNING **: 17:10:07.715: Failed to > >> register client: > >> GDBus.Error:org.gnome.SessionManager.AlreadyRegistered: Unable to > >> register client > >> [sanei_debug] Setting debug level of pixma to 21. > >> [pixma] pixma is compiled with pthread support. > >> [pixma] pixma version 0.17.49 > >> [sanei_debug] Setting debug level of bjnp to 3. > >> [bjnp] sanei_bjnp_find_devices, pixma backend version: 0.17.49 > >> [bjnp] Set new default timeout value: 5000 ms.[bjnp] > >> sanei_bjnp_find_devices: Adding scanner from pixma.conf: > >> bjnp://192.168.0.100:8612 <http://192.168.0.100:8612> > <http://192.168.0.100:8612> > >> [bjnp] > bjnp_allocate_device(bjnp://192.168.0.100:8612/timeout=5000 > <http://192.168.0.100:8612/timeout=5000> > >> <http://192.168.0.100:8612/timeout=5000>) 0 > >> [bjnp] get_scanner_name: Name for 192.168.0.100 not found : Name > >> or service not known > >> [bjnp] setup_udp_socket: Setting up a UDP socket, dest: > >> 192.168.0.100 port 8612 > >> [bjnp] udp_command: ERROR - recv failed: Connection refused[bjnp] > >> udp_command: ERROR - recv failed: Connection refused[bjnp] > >> udp_command: ERROR - recv failed: Connection refused[bjnp] > >> udp_command: ERROR - no data received (timeout = 5000) > >> [bjnp] bjnp_init_device_structure: Cannot read mac address, > >> skipping this scanner > >> [bjnp] bjnp_allocate_device: Scanner not yet in our list, added > >> it: 192.168.0.100:8612 <http://192.168.0.100:8612> > <http://192.168.0.100:8612> > >> [bjnp] setup_udp_socket: Setting up a UDP socket, dest: > >> 192.168.0.100 port 8612 > >> [bjnp] udp_command: ERROR - recv failed: Connection refused[bjnp] > >> udp_command: ERROR - recv failed: Connection refused[bjnp] > >> udp_command: ERROR - recv failed: Connection refused[bjnp] > >> udp_command: ERROR - no data received (timeout = 5000) > >> [bjnp] get_scanner_id: ERROR - Failed to retrieve scanner > identity: > >> [bjnp] add_scanner: ERROR - Cannot read scanner make & model: > >> bjnp://192.168.0.100:8612/timeout=5000 > <http://192.168.0.100:8612/timeout=5000> > >> <http://192.168.0.100:8612/timeout=5000> > >> [bjnp] sanei_bjnp_find_devices: Added all configured > scanners, now > >> do auto detection... > >> [bjnp] prepare_socket: lo is not a valid IPv4 interface, > skipping... > >> [bjnp] prepare_socket: eno1 is IPv4 capable, sending broadcast, > >> socket = 50 > >> [bjnp] prepare_socket: lo is not a valid IPv6 interface, > skipping... > >> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, > >> socket = 51 > >> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, > >> socket = 52 > >> [bjnp] prepare_socket: eno1 is IPv6 capable, sending broadcast, > >> socket = 53 > >> [bjnp] sanei_find_devices: scanner discovery finished... > >> [pixma] pixma_find_scanners() found 0 devices > >> > > > -- sane-devel mailing list: sane-devel@alioth-lists.debian.net https://alioth-lists.debian.net/cgi-bin/mailman/listinfo/sane-devel Unsubscribe: Send mail with subject "unsubscribe your_password" to sane-devel-requ...@lists.alioth.debian.org