[Elecraft] Elecraft CW Net Announcement

Good Evening,    I went for a hike this afternoon.  The mist was hanging in the air.  It felt great to breath without smoke or ash in the air.  It has rained off and on for the last two days.  East of Portland they received over 2 inches.  Hopefully that held true farther south.  I noticed a

Re: [Elecraft] Status of Add-ons for K3?

Did that back when they first announced the pre-order process. My order is still in the queue, according to Elecraft Sales. 73, Pete N4ZR Check out the Reverse Beacon Network at , now spotting RTTY activity worldwide. For spots, please use your favorite "retail" DX

Re: [Elecraft] Local KPA1500 operation via KPA1500 remote

Glad you got it working! 73 Dave wo2x -Original Message- From: Jim Cary Sent: Saturday, September 19, 2020 4:23 PM To: rocke...@gmail.com Cc: elecraft@mailman.qth.net Subject: Re: [Elecraft] Local KPA1500 operation via KPA1500 remote HI Dave, The key was using the “find KPA1500) on

Re: [Elecraft] Local KPA1500 operation via KPA1500 remote

HI Dave, The key was using the “find KPA1500) on the remote tab. Working now. Thanks. 73, Jim W2SM > On Sep 19, 2020, at 4:00 PM, rocke...@gmail.com wrote: > > Verify your baud rate and com port in the remote program (USB) matches the > port and baud when using the utility program. Since

Re: [Elecraft] Local KPA1500 operation via KPA1500 remote

Verify your baud rate and com port in the remote program (USB) matches the port and baud when using the utility program. Since the utility program works the cable connections are good. I am using 230400 baud You can also select Local Connect/USB in the remote program and select find KPA1500.

Re: [Elecraft] No Tx audio after WSJT upgrade

Most likely causes of no TX Audio in a K3S with WSJT-X: 1. Any connector or cable inserted into the K3S 3.5mm LINE IN jack will override (and completely MUTE) the USB Audio CODEC input 2. USB Audio CODEC "Speakers" level got reset to 0 by Windows 3. MAIN:MIC SEL for DATA mode is not

Re: [Elecraft] Status of Add-ons for K3?

Please complete the K3/K3S Options Pre-Order Interest Form . Elecraft can't justify new production of these K3 boards until there is sufficient demand, as indicated by entries on the form (not by posts to this reflector).

Re: [Elecraft] K3 Audio from RS232 connection?

On Thu, Sep 17, 2020 at 10:31 AM Bob KD7YZ wrote: > When I ran up WSJT-X and was attempting to connect, I noticed No Audio. > > How do I get digital audio? I gather it's NOT thru the KIO3b RJ-45 . > If the USB cable is disconnected from the K3S, the USB Sound Card (USB Audio CODEC) will no

[Elecraft] Local KPA1500 operation via KPA1500 remote

I’m having trouble configuring the KPA1500 remote software for local control of my KPA1500 using USB or Ethernet ( I want to locate the amp in the basement). I assume I am supposed to use the “Local Connect” tab, but when I hit the “connect” button, it says “unable to connect on Com………” and

Re: [Elecraft] KRX3 TMP Connectors

You don't need a lot of strength to do it! If it doesn't go in, probably the tip isn't going into the socket. Check to see that the tip is parallel to the shield portion of the connector. Make sure you are putting it in straight. Don't try to force it -- when you have it lined up right, it

[Elecraft] KRX3 TMP Connectors

I removed my KRX3 to install a new filter. My problem is, I can't re-insert one of the TMP connectors. It simply doesn't seat. I've inspected the Tip and it looks OK. I'm 80 and don't have super hand strength, but the first connector went in normally. Any suggestions? Vy 73 de Bob

[Elecraft] Com ports behavior

I have lost radio control on my K3. To find out why, I tried to connect to the K3 Utility. Com5 connects just fine at 38400 bits/sec. When I try to check for firmware, I get a "com5 is closed" message. Have spent a few hours investigating this, but no joy. I can connect just fine to a

Re: [Elecraft] K3: KIO3 digital board failed (I think)

Had the same thing a few years ago. I plugged the PP into the K3 only it was offset a bit. Nanacged to get the cable Red on the K3 Black. Smelled smoke (P3 cable insulation) and blew L1 on the RS232 circuit. Sent from my iPhone ...nr4c. bill > On Sep 18, 2020, at 8:31 PM, Edward R Cole