ot;] K6DGW
Sparks NV DM09dn
Washoe County
Jim McDonald wrote on 10/31/2021 4:05 PM:
From: Bob Wilson, N6TV
Sent: Sunday, October 31, 2021 17:52
To: Jim McDonald
Cc: j...@kk9a.com; Elecraft Reflector
Subject: Re: [Elecraft] Elecraft K-Pod manual updated -- now covers use with
the K4
Did you try
Yes.
73, Jim N7US
From: Bob Wilson, N6TV
Sent: Sunday, October 31, 2021 17:52
To: Jim McDonald
Cc: j...@kk9a.com; Elecraft Reflector
Subject: Re: [Elecraft] Elecraft K-Pod manual updated -- now covers use with
the K4
Did you try upgrading the K-POD firmware to 1.12 to use these new
t@mailman.qth.net>
> *Subject:* Re: [Elecraft] Elecraft K-Pod manual updated -- now covers use
> with the K4
>
>
>
> What is *CONFIG:VFO CTS* set to? Did you try changing it?
>
> 73,
> Bob, N6TV
>
>
>
> On Sat, Oct 30, 2021, 8:06 PM wrote:
>
> I
m: Jim McDonald [mailto:j...@n7us.net<mailto:j...@n7us.net>]
Sent: Friday, October 29, 2021 7:19 PM
To: Bob Wilson, N6TV; j...@kk9a.com<mailto:j...@kk9a.com>; Elecraft Reflector
Subject: RE: [Elecraft] Elecraft K-Pod manual updated -- now covers use with
the K4
My K-Pod tune at half the rate
j...@n7us.net]
> Sent: Friday, October 29, 2021 7:19 PM
> To: Bob Wilson, N6TV; j...@kk9a.com; Elecraft Reflector
> Subject: RE: [Elecraft] Elecraft K-Pod manual updated -- now covers use
> with the K4
>
> My K-Pod tune at half the rate of the K3S at all three VFO CTS settings.
>
>
...@mailman.qth.net On
Behalf Of Bob Wilson, N6TV
Sent: Friday, October 29, 2021 16:59
To: j...@kk9a.com; Elecraft Reflector
Subject: Re: [Elecraft] Elecraft K-Pod manual updated -- now covers use with
the K4
In the K3, if you change *CONFIG:VFO CTS*, the VFO frequency moves faster at
400 than
: Bob Wilson, N6TV
Sent: Friday, October 29, 2021 18:28
To: Jim McDonald ; Elecraft Reflector
Subject: Re: [Elecraft] Elecraft K-Pod manual updated -- now covers use with
the K4
On Fri, Oct 29, 2021 at 4:19 PM Jim McDonald
mailto:j...@n7us.net>> wrote:
My K-Pod tune at half the rate of t
On Fri, Oct 29, 2021 at 4:19 PM Jim McDonald wrote:
> My K-Pod tune at half the rate of the K3S at all three VFO CTS settings.
>
Check again, because that does not match my experience if your K-POD
firmware is at 1.09 (can't test now, sold both K3s). If CONFIG:VFO CTS is
set to 100 (or 200?),
, N6TV
Sent: Friday, October 29, 2021 16:59
To: j...@kk9a.com; Elecraft Reflector
Subject: Re: [Elecraft] Elecraft K-Pod manual updated -- now covers use with
the K4
In the K3, if you change *CONFIG:VFO CTS*, the VFO frequency moves faster at
400 than at 100 (counts per turn), but the K-POD
In the K3, if you change *CONFIG:VFO CTS*, the VFO frequency moves faster
at 400 than at 100 (counts per turn), but the K-POD always tunes at 100 or
200 counts per turn (can't remember which). The K-POD ignores the VFO CTS
setting on a K3.
In the K4, the equivalent setting is *MENU:VFO Counts
"... except for the slow tuning." I must be missing something. My
K-Pod tunes at the same rate as the K3. I have one of the K-Pod buttons
emulating the FINE/COARSE button on the radio ... use it all the time.
Maybe the rates I have my K3 configured for just happen to match the
encoder
I really like the K-POD, except for the slow tuning. Too bad that the K3
firmware "cannot" reprogram it.
John KK9A
Bob Wilson, N6TV wrote:
Yes, this only works with the K4. The K3 firmware cannot reprogram the
K-POD encoder to match the K3's tuning rate.
73,
Bob, N6TV
On Thu, Oct 28, 2021 at 5:33 PM Jim McDonald wrote:
> Does the selection of encoder rates only apply to the K4?
>
Yes, this only works with the K4. The K3 firmware cannot reprogram the
K-POD encoder to match the K3's tuning rate.
73,
Bob, N6TV
Does the selection of encoder rates only apply to the K4?
73, Jim N7US
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of Wayne Burdick
Sent: Thursday, October 28, 2021 10:49
To: Elecraft Reflector
Subject: [Elecraft] Elecraft K-Pod manual updated -- now covers
On Thu, Oct 28, 2021 at 3:50 PM Rick Tavan wrote:
> Right. The macros are stored in the radios, not in the K*Pod. You need to
> run K3 Utility at the radio site to load them into the K3. The K4 has a
> primitive text editor for on-screen macro entry, one finger typing with no
> tactile
Right. The macros are stored in the radios, not in the K*Pod. You need to
run K3 Utility at the radio site to load them into the K3. The K4 has a
primitive text editor for on-screen macro entry, one finger typing with no
tactile feedback. Not fun but no computer required.
/Rick N6XI
On Thu, Oct
I’m right handed and use my right hand to send CW as well as to copy. So, the
iPod is particularly convenieent to adjust the radio (especially RIT for
off-frequency responses).
I use it every day… can’t believe how convenient it is!
Tom W4KX
K4 #110
K3 #969
> On Oct 28, 2021, at 2:32 PM,
Adventures in my 20's followed by a steady accumulation of birthdays has
left me with arm/shoulder deficiencies, aggravated by reaching out to
tune and adjust a radio. The K-Pod is the best accessory I purchased for
my very early K3 [S/N 642]. It gets the tuning and 95% of the switch
The K-Pod is an accessory control panel that's ideal for use with the K4. It
provides 16 switch functions; control of VFO A/VFO B/RIT-XIT offset; and three
general purpose open-drain outputs for station control. You can use the K4's
macro editor to create command sequences to assign to K-Pod
19 matches
Mail list logo