Hi Guys, Thanks heaps for all your help, I did need to use a bridge.
It now seems to detect everything, just need to fine tune it. Cheers, Sam Christoph Willing wrote: > > On 17/07/2007, at 9:03 PM, Samuel Gundry wrote: > >> Hi Chris and Markus, >> >> Thanks for the responses. I cannot see the two entries of my own node >> or the "APAG AudioReflector" node in Rat itself, when in the Audio >> Reflector venue. >> >> I turned off the firewall (I know, silly) and installed the audio >> reflector controller app and received the following error: >>> 17/07/2007 20:53:51 : Started >>> 17/07/2007 20:54:12 : Failed contacting server (socket.error:(10060, >>> 'Operation timted out')) >> I adjusted the reflection delay and pressed apply but it still timed >> out... It certainly seems like a firewall error of sorts, any ideas? >> Might be my router, do I need to open a specific port? > > > Sam, > > There are 2 issues involved concerning the controller application. > Firstly, the existing controller app was written for AG2 and, secondly, > the reflector server location (which is hard coded into the app) is out > of date. > > I've created an updated controller shared application for AG3 and put it > in the Data section of the Audio Reflector venue of the > vv3.ap-accessgrid.org venue server. I've just tested it from home (no > multicast) and it works fine although there are no built-in sounds > available on the server. > > >> The bars in Rat are moving up and down as I speak into the >> microphone, but there is no bars in the listen section. Does this >> mean that my microphone input is local for Rat, but the server cannot >> be contacted to listen to the sound? > > It looks that way. Have you tried connecting via a bridge? That may work > around a multicast problem at your end. > > > chris > > >> Markus Buchhorn wrote: >>> You should also run the audio reflector controller application (which >>> is normally stored in the venue data - I can't check or test right >>> now). That has the option to play back standard sounds stored in the >>> reflector, so you can test inbound paths separately from outbound. >>> >>> Cheers, >>> Markus >>> >>> At 10:35 AM 17/07/2007, Christoph Willing wrote: >>> >>> >>> >>>> On 16/07/2007, at 8:26 PM, Samuel Gundry wrote: >>>> >>>> >>>> >>>>> Hi, >>>>> >>>>> The audio reflector and the second participant of me don't appear >>>>> when I visit the "Audio Reflector" venue (for AG 3.0.2), as per the >>>>> instructions here: >>>>> <http://www.accessgrid.org/node/354>http://www.accessgrid.org/node/354 >>>>> >>>>> Does the room work for anyone else? Or is the room broken? >>>>> >>>>> >>>>> >>>> I used it successfully yesterday when testing a laptop node in the >>>> Library and again just now from our lab node. >>>> >>>> >>>> >>>> >>>>> I'm using this address: >>>>> <https://vv3.ap-accessgrid.org:8000/Venues/00000103104e90bd0081004e009d00a8bbc>https://vv3.ap-accessgrid.org:8000/Venues/00000103104e90bd0081004e009d00a8bbc >>>>> >>>>> I want to test out my sound (obviously), the bars in RAT are moving >>>>> but I don't have any way to test the sound... >>>>> >>>>> >>>>> >>>> Perhaps your signal isn't reaching the reflector. When you're in >>>> that venue, you should see the "APAG AudioReflector" entry in rat >>>> itself. You should also see 2 entries for your own node. If you >>>> don't see all those entries then your traffic isn't being seen (and >>>> audio reflection can't work) - therefore check your firewalls, >>>> multicast etc. >>>> >>>> >>>> chris >>>> >>>> >>>> Christoph Willing +61 7 3365 8350 >>>> QCIF Access Grid Manager >>>> University of Queensland >>>> >>>> >>>> >>>> >>> >>> >>> >> > > Christoph Willing +61 7 3365 8350 > QCIF Access Grid Manager > University of Queensland > > >
