http://bugzilla.kernel.org/show_bug.cgi?id=10847
------- Comment #8 from [EMAIL PROTECTED] 2008-06-05 10:41 -------
The system freezed again, after one hour uptime, for about 4 minutes
until I sent a flood of icmp pings to its NIC, and it woke up. The clock
(as reported by command "date") stayed behind for 4 minutes.
And again half an hour later.
Can this be related to the NIC drivers (r8169) ?
# lsmod
Module Size Used by
nfs 122040 0
lockd 62448 1 nfs
sunrpc 168840 4 nfs,lockd
fuse 42224 4
ipv6 247464 20
af_packet 18056 0
autofs4 20168 1
snd_pcm_oss 37824 0
snd_mixer_oss 14592 1 snd_pcm_oss
snd_seq_dummy 3268 0
snd_seq_oss 29120 0
snd_seq_midi_event 6912 1 snd_seq_oss
snd_seq 48608 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device 6868 3 snd_seq_dummy,snd_seq_oss,snd_seq
usb_storage 41088 0
usbhid 27936 0
snd_hda_intel 352612 1
snd_pcm 71944 2 snd_pcm_oss,snd_hda_intel
snd_timer 19720 2 snd_seq,snd_pcm
snd 52008 10
snd_pcm_oss,snd_mixer_oss,snd_seq_oss,snd_seq,snd_seq_device,snd_hda_intel,snd_pcm,snd_timer
ehci_hcd 31372 0
soundcore 6816 1 snd
snd_page_alloc 8208 2 snd_hda_intel,snd_pcm
pcspkr 3008 0
r8169 26628 0
ohci_hcd 20804 0
video 18772 0
fglrx 1748032 26
usbcore 133936 5 usb_storage,usbhid,ehci_hcd,ohci_hcd
output 3520 1 video
shpchp 29596 0
pci_hotplug 13512 1 shpchp
joydev 10688 0
unix 26232 934
# dmesg
Linux version 2.6.24-gentoo-r8 ([EMAIL PROTECTED]) (gcc version 4.1.2 (Gentoo
4.1.2 p1.1)) #1 SMP Mon Jun 2 18:07:16 EEST 2008
Command line: root=/dev/sda10 ro printk.time=1 vga=791
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000097e80000 (usable)
BIOS-e820: 0000000097e80000 - 0000000097e90000 (ACPI data)
BIOS-e820: 0000000097e90000 - 0000000097e92000 (ACPI NVS)
BIOS-e820: 0000000097e92000 - 00000000b0000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000150000000 (usable)
Entering add_active_range(0, 0, 157) 0 entries of 256 used
Entering add_active_range(0, 256, 622208) 1 entries of 256 used
Entering add_active_range(0, 1048576, 1376256) 2 entries of 256 used
end_pfn_map = 1376256
DMI present.
ACPI: RSDP 000F7FD0, 0024 (r2 PTLTD )
ACPI: XSDT 97E89632, 0054 (r1 GATEWA SYSTEM 6040000 LTP 0)
ACPI: FACP 97E8FA5A, 00F4 (r3 ATI Herring 6040000 ATI F4240)
ACPI: DSDT 97E89686, 63D4 (r1 GATEWA SYSTEM 6040000 MSFT 3000000)
ACPI: FACS 97E91FC0, 0040
ACPI: TCPA 97E8FBC2, 0032 (r2 AMD 6040000 PTEC 0)
ACPI: SSDT 97E8FBF4, 0206 (r1 PTLTD POWERNOW 6040000 LTP 1)
ACPI: SLIC 97E8FDFA, 0176 (r1 GATEWA SYSTEM 6040000 *TK* 1)
ACPI: APIC 97E8FF70, 0054 (r1 PTLTD APIC 6040000 LTP 0)
ACPI: MCFG 97E8FFC4, 003C (r1 PTLTD MCFG 6040000 LTP 0)
Entering add_active_range(0, 0, 157) 0 entries of 256 used
Entering add_active_range(0, 256, 622208) 1 entries of 256 used
Entering add_active_range(0, 1048576, 1376256) 2 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1376256
Movable zone start PFN for each node
early_node_map[3] active PFN ranges
0: 0 -> 157
0: 256 -> 622208
0: 1048576 -> 1376256
On node 0 totalpages: 949789
DMA zone: 56 pages used for memmap
DMA zone: 1162 pages reserved
DMA zone: 2779 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 603832 pages, LIFO batch:31
Normal zone: 4480 pages used for memmap
Normal zone: 323200 pages, LIFO batch:31
Movable zone: 0 pages used for memmap
ATI board detected. Disabling timer routing over 8254.
ACPI: PM-Timer IO Port: 0x8008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
swsusp: Registered nosave memory region: 000000000009d000 - 000000000009e000
swsusp: Registered nosave memory region: 000000000009e000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000d0000
swsusp: Registered nosave memory region: 00000000000d0000 - 0000000000100000
swsusp: Registered nosave memory region: 0000000097e80000 - 0000000097e90000
swsusp: Registered nosave memory region: 0000000097e90000 - 0000000097e92000
swsusp: Registered nosave memory region: 0000000097e92000 - 00000000b0000000
swsusp: Registered nosave memory region: 00000000b0000000 - 00000000e0000000
swsusp: Registered nosave memory region: 00000000e0000000 - 00000000f0000000
swsusp: Registered nosave memory region: 00000000f0000000 - 00000000fec00000
swsusp: Registered nosave memory region: 00000000fec00000 - 00000000fec10000
swsusp: Registered nosave memory region: 00000000fec10000 - 00000000fee00000
swsusp: Registered nosave memory region: 00000000fee00000 - 00000000fee01000
swsusp: Registered nosave memory region: 00000000fee01000 - 00000000fff00000
swsusp: Registered nosave memory region: 00000000fff00000 - 0000000100000000
Allocating PCI resources starting at b4000000 (gap: b0000000:30000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 33184 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 929811
Kernel command line: root=/dev/sda10 ro printk.time=1 vga=791
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] TSC calibrated against PM_TIMER
[ 46.788988] Marking TSC unstable due to TSCs unsynchronized
[ 46.788991] time.c: Detected 1999.967 MHz processor.
[ 46.789025] Console: colour dummy device 80x25
[ 46.789028] console [tty0] enabled
[ 46.791820] Dentry cache hash table entries: 524288 (order: 10,
4194304 bytes)
[ 46.795981] Inode-cache hash table entries: 262144 (order: 9, 2097152
bytes)
[ 46.797228] Checking aperture...
[ 46.797237] CPU 0: aperture @ 4044000000 size 32 MB
[ 46.797242] Aperture too small (32 MB)
[ 46.807035] No AGP bridge found
[ 46.807040] Your BIOS doesn't leave a aperture memory hole
[ 46.807045] Please enable the IOMMU option in the BIOS setup
[ 46.807050] This costs you 64 MB of RAM
[ 46.850919] Mapping aperture over 65536 KB of RAM @ 8000000
[ 46.885300] Memory: 3647052k/5505024k available (2767k kernel code,
151852k reserved, 1174k data, 228k init)
[ 46.885340] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4,
CPUs=2, Nodes=1
[ 46.965637] Calibrating delay using timer specific routine.. 4068.28
BogoMIPS (lpj=6778055)
[ 46.965671] Security Framework initialized
[ 46.965681] Capability LSM initialized
[ 46.965692] Mount-cache hash table entries: 256
[ 46.965807] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 46.965814] CPU: L2 Cache: 512K (64 bytes/line)
[ 46.965820] CPU: Physical Processor ID: 0
[ 46.965825] CPU: Processor Core ID: 0
[ 46.965851] SMP alternatives: switching to UP code
[ 46.966347] ACPI: Core revision 20070126
[ 48.091867] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 48.125430] Using local APIC timer interrupts.
[ 48.175437] APIC timer calibration result 12499809
[ 48.175439] Detected 12.499 MHz APIC timer.
[ 48.175518] SMP alternatives: switching to SMP code
[ 48.175978] Booting processor 1/2 APIC 0x1
[ 48.184113] Initializing CPU#1
[ 48.266672] Calibrating delay using timer specific routine.. 4001.66
BogoMIPS (lpj=6666661)
[ 48.266678] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 48.266680] CPU: L2 Cache: 512K (64 bytes/line)
[ 48.266683] CPU: Physical Processor ID: 0
[ 48.266684] CPU: Processor Core ID: 1
[ 48.266782] AMD Turion(tm) 64 X2 Mobile Technology TL-60 stepping 01
[ 48.266792] AMD C1E detected late. Force timer broadcast.
[ 48.268954] Brought up 2 CPUs
[ 48.269168] net_namespace: 120 bytes
[ 48.269551] NET: Registered protocol family 16
[ 48.269715] ACPI: bus type pci registered
[ 48.270338] PCI: Using MMCONFIG at e0000000 - e12fffff
[ 48.271573] ACPI: EC: Look up EC in DSDT
[ 48.273731] ACPI: BIOS _OSI(Linux) query ignored
[ 48.273739] ACPI: DMI System Vendor: Gateway
[ 48.273744] ACPI: DMI Product Name: T-1625
[ 48.273749] ACPI: DMI Product Version: 90.03
[ 48.273754] ACPI: DMI Board Name:
[ 48.273758] ACPI: DMI BIOS Vendor: Gateway
[ 48.273763] ACPI: DMI BIOS Date: 09/27/2007
[ 48.273767] ACPI: Please send DMI info above to
[EMAIL PROTECTED]
[ 48.273773] ACPI: If "acpi_osi=Linux" works better, please notify
[EMAIL PROTECTED]
[ 48.274005] ACPI: Interpreter enabled
[ 48.274011] ACPI: (supports S0 S3 S4 S5)
[ 48.274026] ACPI: Using IOAPIC for interrupt routing
[ 48.275099] ACPI: EC: non-query interrupt received, switching to
interrupt mode
[ 48.276202] ACPI: EC: GPE = 0x10, I/O: command/status = 0x66, data = 0x62
[ 48.276209] ACPI: EC: driver started in interrupt mode
[ 48.276248] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 48.277421] PCI: Transparent bridge - 0000:00:14.4
[ 48.277450] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 48.277626] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT]
[ 48.277730] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB7_._PRT]
[ 48.277847] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT]
[ 48.277905] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
[ 48.281124] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled.
[ 48.281235] ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled.
[ 48.281339] ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled.
[ 48.281442] ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled.
[ 48.281548] ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled.
[ 48.281652] ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled.
[ 48.281755] ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled.
[ 48.281858] ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled.
[ 48.281975] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 48.282007] pnp: PnP ACPI init
[ 48.282017] ACPI: bus type pnp registered
[ 48.284462] pnp: PnP ACPI: found 10 devices
[ 48.284469] ACPI: ACPI bus type pnp unregistered
[ 48.284607] SCSI subsystem initialized
[ 48.284661] libata version 3.00 loaded.
[ 48.284866] PCI: Using ACPI for IRQ routing
[ 48.284872] PCI: If a device doesn't work, try "pci=routeirq". If it
helps, post a report
[ 48.284884] PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0
[ 48.284889] PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0
[ 48.296863] DMAR:No DMAR devices found
[ 48.296916] PCI-DMA: Disabling AGP.
[ 48.297826] PCI-DMA: aperture base @ 8000000 size 65536 KB
[ 48.297838] PCI-DMA: using GART IOMMU.
[ 48.297847] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 48.298417] ACPI: RTC can wake from S4
[ 48.310228] system 00:01: iomem range 0xfec00000-0xfec00fff could not
be reserved
[ 48.310238] system 00:01: iomem range 0xfee00000-0xfee00fff could not
be reserved
[ 48.310253] system 00:08: ioport range 0x1080-0x1080 has been reserved
[ 48.310260] system 00:08: ioport range 0x200-0x20f has been reserved
[ 48.310266] system 00:08: ioport range 0x220-0x22f has been reserved
[ 48.310272] system 00:08: ioport range 0x40b-0x40b has been reserved
[ 48.310279] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 48.310285] system 00:08: ioport range 0x4d6-0x4d6 has been reserved
[ 48.310291] system 00:08: ioport range 0x530-0x537 has been reserved
[ 48.310297] system 00:08: ioport range 0xc00-0xc01 has been reserved
[ 48.310303] system 00:08: ioport range 0xc14-0xc14 has been reserved
[ 48.310310] system 00:08: ioport range 0xc50-0xc52 has been reserved
[ 48.310316] system 00:08: ioport range 0xc6c-0xc6c has been reserved
[ 48.310322] system 00:08: ioport range 0xc6f-0xc6f has been reserved
[ 48.310328] system 00:08: ioport range 0xcd0-0xcd1 has been reserved
[ 48.310334] system 00:08: ioport range 0xcd2-0xcd3 has been reserved
[ 48.310340] system 00:08: ioport range 0xcd4-0xcd5 has been reserved
[ 48.310346] system 00:08: ioport range 0xcd6-0xcd7 has been reserved
[ 48.310352] system 00:08: ioport range 0xcd8-0xcdf has been reserved
[ 48.310359] system 00:08: ioport range 0x8000-0x805f has been reserved
[ 48.310365] system 00:08: ioport range 0xf40-0xf47 has been reserved
[ 48.310371] system 00:08: ioport range 0x87f-0x87f has been reserved
[ 48.310381] system 00:09: iomem range 0xe0000-0xfffff could not be
reserved
[ 48.310388] system 00:09: iomem range 0xfff00000-0xffffffff could not
be reserved
[ 48.310397] system 00:09: iomem range 0xffb83020-0xffb8401f has been
reserved
[ 48.310403] system 00:09: iomem range 0xfed00000-0xfed003ff has been
reserved
[ 48.310410] system 00:09: iomem range 0x0-0x0 could not be reserved
[ 48.310539] PCI: Bridge: 0000:00:01.0
[ 48.310545] IO window: 9000-9fff
[ 48.310551] MEM window: cfd00000-cfefffff
[ 48.310556] PREFETCH window: b0000000-bfffffff
[ 48.310562] PCI: Bridge: 0000:00:05.0
[ 48.310566] IO window: disabled.
[ 48.310572] MEM window: disabled.
[ 48.310576] PREFETCH window: disabled.
[ 48.310582] PCI: Bridge: 0000:00:07.0
[ 48.310587] IO window: a000-afff
[ 48.310593] MEM window: f0200000-f02fffff
[ 48.310598] PREFETCH window: c0000000-c00fffff
[ 48.310604] PCI: Bridge: 0000:00:14.4
[ 48.310608] IO window: disabled.
[ 48.310619] MEM window: disabled.
[ 48.310625] PREFETCH window: disabled.
[ 48.310649] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 48.310655] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 48.310670] NET: Registered protocol family 2
[ 48.315646] Time: acpi_pm clocksource has been installed.
[ 48.315661] Clockevents: could not switch to one-shot
mode:<6>Clockevents: could not switch to one-shot mode: lapic is not
functional.
[ 48.313549] Could not switch to high resolution mode on CPU 1
[ 48.315681] lapic is not functional.
[ 48.315686] Could not switch to high resolution mode on CPU 0
[ 48.350247] IP route cache hash table entries: 131072 (order: 8,
1048576 bytes)
[ 48.351138] TCP established hash table entries: 262144 (order: 10,
4194304 bytes)
[ 48.353282] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 48.353875] TCP: Hash tables configured (established 262144 bind 65536)
[ 48.353885] TCP reno registered
[ 48.370314] Total HugeTLB memory allocated, 0
[ 48.372011] VFS: Disk quotas dquot_6.5.1
[ 48.372089] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 48.372561] SGI XFS with ACLs, security attributes, realtime, large
block/inode numbers, no debug enabled
[ 48.373051] SGI XFS Quota Management subsystem
[ 48.373222] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 48.373233] io scheduler noop registered
[ 48.373339] io scheduler cfq registered (default)
[ 48.375157] Boot video device is 0000:01:05.0
[ 48.375315] PCI: Setting latency timer of device 0000:00:05.0 to 64
[ 48.375335] assign_interrupt_mode Found MSI capability
[ 48.375365] Allocate Port Service[0000:00:05.0:pcie00]
[ 48.375403] Allocate Port Service[0000:00:05.0:pcie02]
[ 48.375432] Allocate Port Service[0000:00:05.0:pcie03]
[ 48.375488] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 48.375507] assign_interrupt_mode Found MSI capability
[ 48.375529] Allocate Port Service[0000:00:07.0:pcie00]
[ 48.375561] Allocate Port Service[0000:00:07.0:pcie03]
[ 48.398132] Real Time Clock Driver v1.12ac
[ 48.398225] Linux agpgart interface v0.102
[ 48.398351] vesafb: framebuffer at 0xb0000000, mapped to
0xffffc20001400000, using 3072k, total 16384k
[ 48.398362] vesafb: mode is 1024x768x16, linelength=2048, pages=9
[ 48.398368] vesafb: scrolling: redraw
[ 48.398373] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 48.445738] Console: switching to colour frame buffer device 128x48
[ 48.489244] fb0: VESA VGA frame buffer device
[ 48.491927] ACPI: AC Adapter [AC] (on-line)
[ 48.520616] ACPI: Battery Slot [BAT0] (battery present)
[ 48.521239] input: Power Button (FF) as /class/input/input0
[ 48.536841] ACPI: Power Button (FF) [PWRF]
[ 48.537271] input: Power Button (CM) as /class/input/input1
[ 48.550171] ACPI: Power Button (CM) [PWRB]
[ 48.550606] input: Sleep Button (CM) as /class/input/input2
[ 48.563506] ACPI: Sleep Button (CM) [SLPB]
[ 48.563933] input: Lid Switch as /class/input/input3
[ 48.565446] ACPI: Lid Switch [LID]
[ 48.568040] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 48.570820] console [netcon0] enabled
[ 51.457971] netconsole: network logging started
[ 51.478211] Clockevents: could not switch to one-shot mode: lapic is
not functional.
[ 51.478214] Could not switch to high resolution mode on CPU 0
[ 51.476095] Clockevents: could not switch to one-shot mode: lapic is
not functional.
[ 51.476099] Could not switch to high resolution mode on CPU 1
[ 51.548513] Driver 'sd' needs updating - please use bus_type methods
[ 51.566577] Driver 'sr' needs updating - please use bus_type methods
[ 51.584310] ahci 0000:00:12.0: version 3.0
[ 51.584331] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level,
low) -> IRQ 22
[ 51.602319] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing
32bit
[ 51.620115] ahci 0000:00:12.0: controller can't do PMP, turning off
CAP_PMP
[ 52.639880] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps
0xf impl SATA mode
[ 52.657487] ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pio
slum part
[ 52.675428] scsi0 : ahci
[ 52.692870] scsi1 : ahci
[ 52.710043] scsi2 : ahci
[ 52.726844] scsi3 : ahci
[ 52.743042] ata1: SATA max UDMA/133 abar [EMAIL PROTECTED] port
0xf0309100 irq 22
[ 52.759464] ata2: SATA max UDMA/133 abar [EMAIL PROTECTED] port
0xf0309180 irq 22
[ 52.775452] ata3: SATA max UDMA/133 abar [EMAIL PROTECTED] port
0xf0309200 irq 22
[ 52.790983] ata4: SATA max UDMA/133 abar [EMAIL PROTECTED] port
0xf0309280 irq 22
[ 53.278601] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 53.345032] ata1.00: ATA-8: WDC WD2500BEVS-22UST0, 01.01A01, max UDMA/133
[ 53.360986] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 53.377837] ata1.00: configured for UDMA/133
[ 53.708552] ata2: SATA link down (SStatus 0 SControl 300)
[ 54.035193] ata3: SATA link down (SStatus 0 SControl 300)
[ 54.361830] ata4: SATA link down (SStatus 0 SControl 300)
[ 54.374734] scsi 0:0:0:0: Direct-Access ATA WDC WD2500BEVS-2
01.0 PQ: 0 ANSI: 5
[ 54.390289] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors
(250059 MB)
[ 54.405736] sd 0:0:0:0: [sda] Write Protect is off
[ 54.420908] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 54.420922] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 54.436674] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors
(250059 MB)
[ 54.452425] sd 0:0:0:0: [sda] Write Protect is off
[ 54.467978] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 54.467990] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 54.483967] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 >
[ 54.632553] sd 0:0:0:0: [sda] Attached SCSI disk
[ 54.648680] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level,
low) -> IRQ 16
[ 54.665064] PCI: Setting latency timer of device 0000:00:14.1 to 64
[ 54.665116] scsi4 : pata_atiixp
[ 54.681271] scsi5 : pata_atiixp
[ 54.697688] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x8420
irq 14
[ 54.713961] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x8428
irq 15
[ 55.045549] ata5.00: ATAPI: HL-DT-ST DVDRAM GSA-T20F, EG02, max UDMA/33
[ 55.228832] ata5.00: configured for UDMA/33
[ 55.396564] scsi 4:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20F
EG02 PQ: 0 ANSI: 5
[ 55.424058] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw
xa/form2 cdda tray
[ 55.440358] Uniform CD-ROM driver Revision: 3.20
[ 55.456453] sr 4:0:0:0: Attached scsi CD-ROM sr0
[ 55.456806] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at
0x60,0x64 irq 1,12
[ 55.478712] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 55.494854] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 55.511092] mice: PS/2 mouse device common for all mice
[ 55.639398] input: AT Translated Set 2 keyboard as /class/input/input4
[ 55.683933] i2c /dev entries driver
[ 55.703041] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 55.719394] cpuidle: using governor ladder
[ 55.736239] cpuidle: using governor menu
[ 55.755403] powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile
Technology TL-60 processors (2 cpu cores) (version 2.20.00)
[ 55.778641] powernow-k8: 0 : fid 0xc (2000 MHz), vid 0x12
[ 55.795791] powernow-k8: 1 : fid 0xa (1800 MHz), vid 0x13
[ 55.812961] powernow-k8: 2 : fid 0x8 (1600 MHz), vid 0x14
[ 55.829692] powernow-k8: 3 : fid 0x0 (800 MHz), vid 0x1e
[ 55.849251] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 56.267624] Clocksource tsc unstable (delta = -251876766 ns)
[ 56.318769] Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1,
caps: 0xa04713/0x0
[ 56.356513] input: SynPS/2 Synaptics TouchPad as /class/input/input5
[ 56.438705] XFS mounting filesystem sda10
[ 56.478249] Ending clean XFS mount for filesystem: sda10
[ 56.478283] VFS: Mounted root (xfs filesystem) readonly.
[ 56.487118] Freeing unused kernel memory: 228k freed
[ 56.928409] NET: Registered protocol family 1
[ 58.111037] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 58.122144] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 58.168032] usbcore: registered new interface driver usbfs
[ 58.168060] usbcore: registered new interface driver hub
[ 58.169910] usbcore: registered new device driver usb
[ 58.216514] fglrx: module license 'Proprietary. (C) 2002 - ATI
Technologies, Starnberg, GERMANY' taints kernel.
[ 58.236709] [fglrx] Maximum main memory to use for locked dma
buffers: 3407 MBytes.
[ 58.236739] [fglrx] ASYNCIO init succeed!
[ 58.237036] [fglrx] PAT is enabled successfully!
[ 58.237057] [fglrx] module loaded - fglrx 8.47.3 [Feb 25 2008] on minor 0
[ 58.243078] input: Video Bus as /class/input/input6
[ 58.256770] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller
(OHCI) Driver
[ 58.256803] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level,
low) -> IRQ 16
[ 58.256992] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 58.257172] ohci_hcd 0000:00:13.0: new USB bus registered, assigned
bus number 1
[ 58.257193] ohci_hcd 0000:00:13.0: irq 16, io mem 0xf0304000
[ 58.257381] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 58.264622] input: PC Speaker as /class/input/input7
[ 58.278281] usb usb1: configuration #1 chosen from 1 choice
[ 58.278309] hub 1-0:1.0: USB hub found
[ 58.278321] hub 1-0:1.0: 2 ports detected
[ 58.319587] ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level,
low) -> IRQ 17
[ 58.319766] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 58.319819] ohci_hcd 0000:00:13.1: new USB bus registered, assigned
bus number 2
[ 58.319842] ohci_hcd 0000:00:13.1: irq 17, io mem 0xf0305000
[ 58.340923] usb usb2: configuration #1 chosen from 1 choice
[ 58.340948] hub 2-0:1.0: USB hub found
[ 58.340958] hub 2-0:1.0: 2 ports detected
[ 58.382213] ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level,
low) -> IRQ 18
[ 58.382387] ohci_hcd 0000:00:13.2: OHCI Host Controller
[ 58.382439] ohci_hcd 0000:00:13.2: new USB bus registered, assigned
bus number 3
[ 58.382460] ohci_hcd 0000:00:13.2: irq 18, io mem 0xf0306000
[ 58.403568] usb usb3: configuration #1 chosen from 1 choice
[ 58.403593] hub 3-0:1.0: USB hub found
[ 58.403603] hub 3-0:1.0: 2 ports detected
[ 58.438132] usb 1-1: new full speed USB device using ohci_hcd and
address 2
[ 58.452375] ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level,
low) -> IRQ 17
[ 58.452548] ohci_hcd 0000:00:13.3: OHCI Host Controller
[ 58.452599] ohci_hcd 0000:00:13.3: new USB bus registered, assigned
bus number 4
[ 58.452620] ohci_hcd 0000:00:13.3: irq 17, io mem 0xf0307000
[ 58.473718] usb usb4: configuration #1 chosen from 1 choice
[ 58.473744] hub 4-0:1.0: USB hub found
[ 58.473754] hub 4-0:1.0: 2 ports detected
[ 58.515031] ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level,
low) -> IRQ 18
[ 58.515204] ohci_hcd 0000:00:13.4: OHCI Host Controller
[ 58.515256] ohci_hcd 0000:00:13.4: new USB bus registered, assigned
bus number 5
[ 58.515272] ohci_hcd 0000:00:13.4: irq 18, io mem 0xf0308000
[ 58.526248] usb 1-1: configuration #1 chosen from 1 choice
[ 58.536380] usb usb5: configuration #1 chosen from 1 choice
[ 58.536406] hub 5-0:1.0: USB hub found
[ 58.536416] hub 5-0:1.0: 2 ports detected
[ 58.575612] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level,
low) -> IRQ 16
[ 58.646115] usb 1-2: new low speed USB device using ohci_hcd and
address 3
[ 58.729443] usb 1-2: configuration #1 chosen from 1 choice
[ 58.848767] usb 2-1: new full speed USB device using ohci_hcd and
address 2
[ 58.934500] usb 2-1: configuration #1 chosen from 1 choice
[ 58.948221] si3054: cannot initialize. EXT MID = 0000
[ 58.948931] ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level,
low) -> IRQ 19
[ 58.949117] ehci_hcd 0000:00:13.5: EHCI Host Controller
[ 58.949167] ehci_hcd 0000:00:13.5: new USB bus registered, assigned
bus number 6
[ 58.949204] ehci_hcd 0000:00:13.5: debug port 1
[ 58.949216] ehci_hcd 0000:00:13.5: irq 19, io mem 0xf0309400
[ 58.952761] ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver
10 Dec 2004
[ 58.952866] usb usb6: configuration #1 chosen from 1 choice
[ 58.952891] hub 6-0:1.0: USB hub found
[ 58.952898] hub 6-0:1.0: 10 ports detected
[ 58.994170] r8169 Gigabit Ethernet driver 2.2LK loaded
[ 58.994187] ACPI: PCI Interrupt 0000:08:00.0[A] -> GSI 19 (level,
low) -> IRQ 19
[ 58.994201] PCI: Setting latency timer of device 0000:08:00.0 to 64
[ 58.994431] eth0: RTL8101e at 0xffffc20000076000, 00:03:25:43:7f:93,
XID 34200000 IRQ 317
[ 58.996675] ACPI: PCI Interrupt 0000:01:05.2[B] -> GSI 19 (level,
low) -> IRQ 19
[ 59.008785] usb 1-1: USB disconnect, address 2
[ 59.058098] usb 1-2: USB disconnect, address 3
[ 59.106102] usb 2-1: USB disconnect, address 2
[ 59.106430] usbcore: registered new interface driver hiddev
[ 59.244736] usb 6-1: new high speed USB device using ehci_hcd and
address 2
[ 59.299602] usb 6-1: configuration #1 chosen from 1 choice
[ 59.459389] usb 6-3: new high speed USB device using ehci_hcd and
address 4
[ 59.511829] usb 6-3: configuration #1 chosen from 1 choice
[ 59.603374] usb 6-8: new high speed USB device using ehci_hcd and
address 5
[ 59.658599] usb 6-8: configuration #1 chosen from 1 choice
[ 59.659271] usbcore: registered new interface driver usbhid
[ 59.659275] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 59.689561] Initializing USB Mass Storage driver...
[ 59.778025] usb 1-2: new low speed USB device using ohci_hcd and
address 4
[ 59.861491] usb 1-2: configuration #1 chosen from 1 choice
[ 59.869249] input: USB Optical Mouse as /class/input/input8
[ 59.887399] input,hidraw0: USB HID v1.10 Mouse [USB Optical Mouse] on
usb-0000:00:13.0-2
[ 59.889008] scsi6 : SCSI emulation for USB Mass Storage devices
[ 59.889879] usbcore: registered new interface driver usb-storage
[ 59.889884] USB Mass Storage support registered.
[ 59.890194] usb-storage: device found at 5
[ 59.890196] usb-storage: waiting for device to settle before scanning
[ 60.611337] Adding 2016116k swap on /dev/sda5. Priority:-1 extents:1
across:2016116k
[ 62.819812] scsi 6:0:0:0: Direct-Access Generic- Multi-Card
1.00 PQ: 0 ANSI: 0 CCS
[ 62.821050] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 62.821316] usb-storage: device scan complete
[ 72.866719] r8169: eth0: link up
[ 72.866726] r8169: eth0: link up
[ 74.083413] NET: Registered protocol family 17
[ 74.552928] NET: Registered protocol family 10
[ 78.939371] eth0: no IPv6 routers present
[ 81.845172] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 18 (level,
low) -> IRQ 18
[ 83.917134] [fglrx] GART Table is not in FRAME_BUFFER range
[ 83.917146] [fglrx] Reserve Block - 0 offset = 0X17ffb000 length =
0X5000
[ 83.917149] [fglrx] Reserve Block - 1 offset = 0X0 length = 0X1000000
[ 84.116697] [fglrx] interrupt source 10000000 successfully enabled
[ 84.116702] [fglrx] enable ID = 0x00000008
[ 84.116909] [fglrx] Receive enable interrupt message with
irqEnableMask: 10000000
[ 97.722290] XFS mounting filesystem sda8
[ 99.731547] Ending clean XFS mount for filesystem: sda8
[ 101.460989] EXT2-fs warning: maximal mount count reached, running
e2fsck is recommended
[ 102.984234] fuse init (API version 7.9)
[ 105.393724] XFS mounting filesystem sda6
[ 105.448431] Ending clean XFS mount for filesystem: sda6
[ 356.745874] RPC: Registered udp transport module.
[ 356.745879] RPC: Registered tcp transport module.
[ 398.559108] APIC error on CPU1: 00(40)
[ 1107.812329] APIC error on CPU1: 40(40)
[ 1166.098196] APIC error on CPU1: 40(40)
[ 1434.699823] APIC error on CPU1: 40(40)
[ 1571.845100] APIC error on CPU1: 40(40)
[ 1630.770205] APIC error on CPU1: 40(40)
--
Configure bugmail: http://bugzilla.kernel.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are on the CC list for the bug, or are watching someone who is.
-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://sourceforge.net/services/buy/index.php
_______________________________________________
acpi-bugzilla mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/acpi-bugzilla
