No a SFP+ will power up and might even show RX of light, but never come
up. It works the other way around to if you put a SFP in a SFP+ they
will often come up and even show RX light at both ends but will not link
up. If its not a dual rate 1/10G SFP+ that could cause issues. Some
don't care, but many don't work too well if you try to run them at
slower speeds.
On 9/24/2021 6:39 PM, Steve Jones wrote:
All documentation I find says it's only sfp. But if it doesnt
workwouldnt it not ID or power?
On Fri, Sep 24, 2021, 6:22 PM Mathew Howard <mhoward...@gmail.com
<mailto:mhoward...@gmail.com>> wrote:
Will an sfp+ module generally work in an sfp port? I'd be
surprised if the Integra has sfp+
On Fri, Sep 24, 2021, 4:33 PM <dmmoff...@gmail.com
<mailto:dmmoff...@gmail.com>> wrote:
If you don’t have a ferrule cleaner you can wipe off the ends
of the patch cable with an alcohol wipe, but I have no idea
how you clean the female connectors without the tool.
-Adam
*From:* dmmoff...@gmail.com <mailto:dmmoff...@gmail.com>
<dmmoff...@gmail.com <mailto:dmmoff...@gmail.com>>
*Sent:* Friday, September 24, 2021 5:18 PM
*To:* 'AnimalFarm Microwave Users Group' <af@af.afmug.com
<mailto:af@af.afmug.com>>
*Subject:* RE: [AFMUG] SFP questions
That “Rx Lose” checkbox at the top on the Mikrotik means
there’s no Rx signal.
The other device shows Rx power of 0
If you know it’s physically connected, but there’s no Rx
signal on either end then I’d wonder if you need to flip-flip
the tx/rx on one end. …..sounds like you already tried that
though.
Did you clean the connectors? A spec of invisible dirt can
stop you.
https://www.amazon.com/Cleaning-1-25mm-Ferrule-Connectors-Cleaner/dp/B07Z2ST9GD
<https://www.amazon.com/Cleaning-1-25mm-Ferrule-Connectors-Cleaner/dp/B07Z2ST9GD>
*From:* AF <af-boun...@af.afmug.com
<mailto:af-boun...@af.afmug.com>> *On Behalf Of *Steve Jones
*Sent:* Friday, September 24, 2021 5:04 PM
*To:* AnimalFarm Microwave Users Group <af@af.afmug.com
<mailto:af@af.afmug.com>>
*Subject:* [AFMUG] SFP questions
Im using my SFPs I have for the Aviat radios to connect
between a SAF integra and a CRS309.
There are two integras 2+0, we lost the original switch that
had the original SFPs in them. So I took the horizontal radio
SFP and paired it in the CRS and that radio links up fine.
However, the SFPs I have for the Aviats dont seem to work. At
first I figured it was just incompatibility (I dont recall if
the Integra is SFP or SFP+, these are SFP+)
In the attached image, both units recognize the SFP and claim
to be transmitting light. Even if there was incompatibility
with the SFP, shouldnt there be an RX? or if they cant
negotiate for whatever reason would it not show an RX?
I did swap the Fiber ends, I havent tried a different cable,
though this was brand new from Aviat.
Would I be correct to assume that if the Devices populate the
info fields, then the SFP should at least connect, even if the
the data channel doesnt work due to incompatibility with the
hardware?
--
AF mailing list
AF@af.afmug.com <mailto:AF@af.afmug.com>
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
<http://af.afmug.com/mailman/listinfo/af_af.afmug.com>
--
AF mailing list
AF@af.afmug.com <mailto:AF@af.afmug.com>
http://af.afmug.com/mailman/listinfo/af_af.afmug.com
<http://af.afmug.com/mailman/listinfo/af_af.afmug.com>
--
AF mailing list
AF@af.afmug.com
http://af.afmug.com/mailman/listinfo/af_af.afmug.com