For these situations where someone might want two configurations, it would be nice to be able to pre-load configurations and if the sm can't connect to an AP for a set amount of time, it loads the other config and tries that, and goes back and forth until it locks on.
On Thu, Oct 9, 2014 at 9:20 AM, Sriram Chaturvedi via Af <af@afmug.com> wrote: > Shayne, > > > > It doesn’t do that automatically. You have to explicitly configure the SM > to operate in Standard WiFi mode (from the Quick Start or > Configuration->Radio page) to connect to an AP operating standard 802.11. > > > > Thanks, > Sriram > > > > *From:* Af [mailto:af-boun...@afmug.com] *On Behalf Of *Shayne Lebrun via > Af > *Sent:* Thursday, October 09, 2014 8:15 AM > > *To:* af@afmug.com > *Subject:* Re: [AFMUG] New ePMP Beta Software 2.3-RC10 available! > > > > Is the basic idea that you’re using an SSID and wpa2 anyway, so when the > ePMP tries to connect, it then identifies the AP as 802.11 or > CanopyMagicSauce and connects accordingly? > > > > *From:* Af [mailto:af-boun...@afmug.com <af-boun...@afmug.com>] *On > Behalf Of *Paul McCall via Af > *Sent:* Wednesday, October 8, 2014 11:25 PM > *To:* af@afmug.com > *Subject:* Re: [AFMUG] New ePMP Beta Software 2.3-RC10 available! > > > > Got it! Makes sense > > > > *From:* Af [mailto:af-boun...@afmug.com <af-boun...@afmug.com>] *On > Behalf Of *timothy steele via Af > *Sent:* Wednesday, October 08, 2014 10:48 PM > *To:* af@afmug.com > *Cc:* af@afmug.com > *Subject:* Re: [AFMUG] New ePMP Beta Software 2.3-RC10 available! > > > > If you turn Airmax off on your UBNT AP's you can slowly swap all CPE's to > Epmp then change AP to Epmp that is what wifi mode is for > > > — > Sent from Mailbox <https://www.dropbox.com/mailbox> > > > > On Wed, Oct 8, 2014 at 10:29 PM, Paul McCall via Af <af@afmug.com> wrote: > > What is the perceived application for the SM operating in standard WiFi > mode ? > > > > *From:* Af [mailto:af-boun...@afmug.com <af-boun...@afmug.com>] *On > Behalf Of *Sriram Chaturvedi via Af > *Sent:* Wednesday, October 08, 2014 7:09 PM > *To:* af@afmug.com > *Subject:* [AFMUG] New ePMP Beta Software 2.3-RC10 available! > > > > Folks, > > > > ePMP Beta software 2.3-RC10 is now available for download here: > https://support.cambiumnetworks.com/files/epmp > > > > System Release 2.3 adds the following features: > > · 5 MHz and 10 MHz channel bandwidth support > > o Max number of subscribers is limited to 30 for 5MHz and 60 for 10 MHz > > · SM Wi-Fi mode support (Only 20 MHz and 40 MHz channel > bandwidths) > > o SM can operate in standard Wi-Fi mode > > · Broadcast Traffic Shaping (Limiting) > > o Ability to limit the number of broadcast packets per second > > · Multicast VLAN and Prioritization > > o Multicast VLAN support with prioritization > > o Ability to leave/join multicast groups and limit number of multicast > groups to up to 5 groups > > o Support for IGMPv3 snooping > > · CLI access via ssh (default credentials: admin/admin) > > · Option to set SM Max Tx power manually > > > > Please post any feedback on the ePMP Beta Forum! > > http://epmpbeta.community.cambiumnetworks.com/ > > > > Thanks, > > Sriram > > > > >