Be careful with Trango BHs. The ones I've looked at tie +48 to chassis
ground. I had to isolate them to keep from popping fuses on my -48
ground system.
bp
<part15sbs{at}gmail{dot}com>
On 4/17/2015 6:06 PM, Jeremy wrote:
Actually, I take that back about the Trango BHs. I forgot I ended up
running fiber and direct DC to the Trangos. I have their rackmount
-48v power supply (Duracomm rebranded I think). I was going to put
positive on every pin but there was no way for negative to be isolated
in my PRM24 rackmount APC surge deal.
On Fri, Apr 17, 2015 at 6:01 PM, Gino Villarini <g...@aeronetpr.com
<mailto:g...@aeronetpr.com>> wrote:
Details on trango.. Cause its –48 with pos on shield
Gino A. Villarini
President
From: Jeremy <jeremysmi...@gmail.com <mailto:jeremysmi...@gmail.com>>
Reply-To: "af@afmug.com <mailto:af@afmug.com>" <af@afmug.com
<mailto:af@afmug.com>>
Date: Friday, April 17, 2015 at 11:05 AM
To: "af@afmug.com <mailto:af@afmug.com>" <af@afmug.com
<mailto:af@afmug.com>>
Subject: Re: [AFMUG] External POE.
+1! I use them on every site that we have. I have powered AF,
AF5X, Trango licensed BHs, Gigabit Nanobeams, non-GB UBNT radios,
cameras, you name it! My favorite part about these is when I
upgrade a radio from 10/100 to Gb all I have to do is add a
jumper. The boxes we build are modular, and can be changed,
upgraded, and expanded with very little work.
On Fri, Apr 17, 2015 at 8:54 AM, Chuck McCown <ch...@wbmfg.com
<mailto:ch...@wbmfg.com>> wrote:
Yes.
-----Original Message----- From: Matt
Sent: Friday, April 17, 2015 8:51 AM
To: af@afmug.com <mailto:af@afmug.com>
Subject: Re: [AFMUG] External POE.
Tested with SAF?
On Fri, Apr 17, 2015 at 9:41 AM, Chuck McCown <ch...@wbmfg.com
<mailto:ch...@wbmfg.com>> wrote:
So far, these have powered every device they have been
called upon to do if
it is GigE circuit.
Or a circuit with 802.1af type of wiring.
http://www.wbmfg.com/products.cfm?PID=77&Cat=
http://www.wbmfg.com/products.cfm?PID=68&Cat=
From: Mathew Howard
Sent: Thursday, April 16, 2015 5:42 PM
To: af
Subject: Re: [AFMUG] Packetflux Gigabit SyncInjector for
24 Volt Cambium
Radios - Ubnt too?
If I remember right, the AF5x pinout is 1/2 & 4/5 positive
and 3/6 & 7/8
negative.
Airmax stuff is all 4/5 positive and 7/8 negative, I
imagine the 10/100
stuff would work fine with the power pairs swapped, but I
don't know what
that would do to gigabit. I don't think it's going to work
with AF5x, since
they use power on all four pairs.
On Thu, Apr 16, 2015 at 6:19 PM, Josh Luthman
<j...@imaginenetworksllc.com
<mailto:j...@imaginenetworksllc.com>>
wrote:
I didn't check...sorry. It's on the roof so I can go
up and look
tomorrow.
Josh Luthman
Office: 937-552-2340 <tel:937-552-2340>
Direct: 937-552-2343 <tel:937-552-2343>
1100 Wayne St
Suite 1337
Troy, OH 45373
On Thu, Apr 16, 2015 at 7:14 PM, George Skorup (Cyber
Broadcasting)
<geo...@cbcast.com <mailto:geo...@cbcast.com>> wrote:
No pinout!?
On 4/16/2015 6:10 PM, Josh Luthman wrote:
It says 24v/1a and is gigabit. It is a bit
different than the Nanobeam
POEs. It also doesn't work with an NSM5 for certain.
Josh Luthman
Office: 937-552-2340 <tel:937-552-2340>
Direct: 937-552-2343 <tel:937-552-2343>
1100 Wayne St
Suite 1337
Troy, OH 45373
On Thu, Apr 16, 2015 at 6:39 PM, George Skorup
(Cyber Broadcasting)
<geo...@cbcast.com <mailto:geo...@cbcast.com>> wrote:
What does the AF5x power supply say on the
label for pairs or pinouts?
Or is it the same as their other 24V/1A
supplies, but gigabit?
On 4/16/2015 5:29 PM, Josh Luthman wrote:
I'm mostly concerned with the Ubnt Airmax
stuff (24v) and AF5x.
Obviously the ePMP works.
Josh Luthman
Office: 937-552-2340 <tel:937-552-2340>
Direct: 937-552-2343 <tel:937-552-2343>
1100 Wayne St
Suite 1337
Troy, OH 45373
On Thu, Apr 16, 2015 at 6:12 PM, George Skorup
(Cyber Broadcasting)
<geo...@cbcast.com <mailto:geo...@cbcast.com>>
wrote:
AFAIK, the 450AP GigE interface is still
powered only on pins 4, 5, 7 &
8. Probably applies to the ePMP Sync radio
too.
So, with that in mind.. does the UBNT GigE
PoE stuff use all 4 pairs
for power? If it's 4, 5, 7 & 8, it may be
possible, but... you'd have to
flip the blues and browns at one end. I
don't know what that would do for
the GigE data interface though. It might
not work. You can use a 568B to
568A (aka standard cross-over) cable and
GigE still works fine, but I'm not
sure about crossed blues and browns.
Someone smarter than me would probably
have to give you a thumbs up or
down.
On 4/16/2015 4:55 PM, Josh Luthman wrote:
Has anyone tried these syncinjectors
for Ubnt Airmax radios? What
about anything else? I'd love to use
this one product for all sites from
now on.
Is it possible to run the AF5x?
Josh Luthman
Office: 937-552-2340 <tel:937-552-2340>
Direct: 937-552-2343 <tel:937-552-2343>
1100 Wayne St
Suite 1337
Troy, OH 45373