I did a ubnt pico attached to a 751 one time for vacation in Dominican Republic. I'd imagine that would fit your bill, although probable not the "best" solution. However you might be able to do a 493g with 2 wireless cards. I think there's an issue with having a single wireless card in both AP and Client mode. So if you have 2 cards, shouldn't that work? There may be more elegant solutions by now but I think this would get it all in one case.
Thanks Tyler ___________________________ Mangled by my iPhone. ___________________________ Tyler Treat Corn Belt Technologies, Inc. [email protected]<mailto:[email protected]> ___________________________ On Jun 1, 2015, at 3:53 PM, Forrest Christian (List Account) <[email protected]<mailto:[email protected]>> wrote: I guess you could call the functionality I'm looking for more of the "Repeater" or "Mesh" operation, but with NAT in the middle..... I.E. today you can, add a virtual AP to a Mikrotik device, so it looks like two devices. I'm looking for the functionality where you can add both a 'wireless AP' and 'client bridge' to the same device. Yes, I know all about the whole 'speed getting slower with WDS/mess issue, etc.), but in this case it doesn't really matter since the traffic is going to be next to nothing. It seems that most hardware and/or drivers will only permit you to be in "AP" or "Client" mode. Like I said, I swear I've seen a device which actually works in both at the same time with the same radio - either that or some small device which has two radios in it. Otherwise, I'll just go the separate AP and client bridge route. -forrest On Mon, Jun 1, 2015 at 2:30 PM, Josh Luthman <[email protected]<mailto:[email protected]>> wrote: Ether1/poe in pulls DHCP and gets your Internet bridge1 (ether2/wlan0) is 172.16.0.1/24<http://172.16.0.1/24> and gets NATed What are you missing? Josh Luthman Office: 937-552-2340<tel:937-552-2340> Direct: 937-552-2343<tel:937-552-2343> 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Jun 1, 2015 at 4:28 PM, Forrest Christian (List Account) <[email protected]<mailto:[email protected]>> wrote: Maybe. I'm actually probably going to buy one of those and the mAP just to play with. I have some ideas. I swear I've seen something which was designed to connect to a hotspot, then NAT the hotspot connection and deliver it through both AP and wired modes. You know, so you could connect your wired and wireless devices on what appears to be a single connection. I probably need 2 (usable) or 3 (great) Ethernet ports. -forrest On Mon, Jun 1, 2015 at 1:55 PM, Josh Luthman <[email protected]<mailto:[email protected]>> wrote: Can you use this and a POE switch? http://routerboard.com/RBmAP2n Josh Luthman Office: 937-552-2340<tel:937-552-2340> Direct: 937-552-2343<tel:937-552-2343> 1100 Wayne St Suite 1337 Troy, OH 45373 On Mon, Jun 1, 2015 at 3:53 PM, Forrest Christian (List Account) <[email protected]<mailto:[email protected]>> wrote: Question for those of you who deal with WiFi devices a lot more than I do: I am in the market for a small WiFi access point which I can use primarily to connect a small Ethernet network to wireless devices (tablets, phones). This is a trade show application - aka 2-3 Ethernet demo devices attached via WiFi. I'm looking for small, light, and although battery would be nice occasionally, "wall power" is a must, even if it is just leave it plugged into the charger while operating. I'm going to be flying with this device so I don't want something large and clunky. Bonus for a device which will also act as a wifi client/nat router at the same time.... aka act as a "WISP client" AND at the same time act as an AP. Not sure if this exists or is even possible with current hardware..... If not, if there's a teensy wisp client out there with ethernet for this type of application, feel free to point me there... My fallback position is probably a RB951, although the new hAP light product is intriguing (not sure if it is even shipping yet). -- Forrest Christian CEO, PacketFlux Technologies, Inc. Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 [email protected]<mailto:[email protected]> | http://www.packetflux.com<http://www.packetflux.com/> [https://s3.amazonaws.com/images.wisestamp.com/icons/linkedin.png]<http://www.linkedin.com/in/fwchristian> [https://s3.amazonaws.com/images.wisestamp.com/icons/facebook.png] <http://facebook.com/packetflux> [https://s3.amazonaws.com/images.wisestamp.com/icons/twitter.png] <http://twitter.com/@packetflux> -- Forrest Christian CEO, PacketFlux Technologies, Inc. Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 [email protected]<mailto:[email protected]> | http://www.packetflux.com<http://www.packetflux.com/> [https://s3.amazonaws.com/images.wisestamp.com/icons/linkedin.png]<http://www.linkedin.com/in/fwchristian> [https://s3.amazonaws.com/images.wisestamp.com/icons/facebook.png] <http://facebook.com/packetflux> [https://s3.amazonaws.com/images.wisestamp.com/icons/twitter.png] <http://twitter.com/@packetflux> -- Forrest Christian CEO, PacketFlux Technologies, Inc. Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 [email protected]<mailto:[email protected]> | http://www.packetflux.com<http://www.packetflux.com/> [https://s3.amazonaws.com/images.wisestamp.com/icons/linkedin.png]<http://www.linkedin.com/in/fwchristian> [https://s3.amazonaws.com/images.wisestamp.com/icons/facebook.png] <http://facebook.com/packetflux> [https://s3.amazonaws.com/images.wisestamp.com/icons/twitter.png] <http://twitter.com/@packetflux>
