Get 2 airgateways take the boards out of the case re wire it for what you need put your own case on it get a small RC battery for power when on the move
— Sent from Mailbox On Mon, Jun 1, 2015 at 11:47 PM, Tyler Treat <[email protected]> wrote: > I did a ubnt pico attached to a 751 one time for vacation in Dominican > Republic. I'd imagine that would fit your bill, although probable not the > "best" solution. However you might be able to do a 493g with 2 wireless > cards. > I think there's an issue with having a single wireless card in both AP and > Client mode. So if you have 2 cards, shouldn't that work? There may be > more elegant solutions by now but I think this would get it all in one case. > Thanks > Tyler > ___________________________ > Mangled by my iPhone. > ___________________________ > Tyler Treat > Corn Belt Technologies, Inc. > [email protected]<mailto:[email protected]> > ___________________________ > On Jun 1, 2015, at 3:53 PM, Forrest Christian (List Account) > <[email protected]<mailto:[email protected]>> wrote: > I guess you could call the functionality I'm looking for more of the > "Repeater" or "Mesh" operation, but with NAT in the middle..... > I.E. today you can, add a virtual AP to a Mikrotik device, so it looks like > two devices. I'm looking for the functionality where you can add both a > 'wireless AP' and 'client bridge' to the same device. Yes, I know all about > the whole 'speed getting slower with WDS/mess issue, etc.), but in this case > it doesn't really matter since the traffic is going to be next to nothing. > It seems that most hardware and/or drivers will only permit you to be in "AP" > or "Client" mode. Like I said, I swear I've seen a device which actually > works in both at the same time with the same radio - either that or some > small device which has two radios in it. > Otherwise, I'll just go the separate AP and client bridge route. > -forrest > On Mon, Jun 1, 2015 at 2:30 PM, Josh Luthman > <[email protected]<mailto:[email protected]>> wrote: > Ether1/poe in pulls DHCP and gets your Internet > bridge1 (ether2/wlan0) is 172.16.0.1/24<http://172.16.0.1/24> and gets NATed > What are you missing? > Josh Luthman > Office: 937-552-2340<tel:937-552-2340> > Direct: 937-552-2343<tel:937-552-2343> > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > On Mon, Jun 1, 2015 at 4:28 PM, Forrest Christian (List Account) > <[email protected]<mailto:[email protected]>> wrote: > Maybe. I'm actually probably going to buy one of those and the mAP just to > play with. I have some ideas. > I swear I've seen something which was designed to connect to a hotspot, then > NAT the hotspot connection and deliver it through both AP and wired modes. > You know, so you could connect your wired and wireless devices on what > appears to be a single connection. I probably need 2 (usable) or 3 > (great) Ethernet ports. > -forrest > On Mon, Jun 1, 2015 at 1:55 PM, Josh Luthman > <[email protected]<mailto:[email protected]>> wrote: > Can you use this and a POE switch? http://routerboard.com/RBmAP2n > Josh Luthman > Office: 937-552-2340<tel:937-552-2340> > Direct: 937-552-2343<tel:937-552-2343> > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > On Mon, Jun 1, 2015 at 3:53 PM, Forrest Christian (List Account) > <[email protected]<mailto:[email protected]>> wrote: > Question for those of you who deal with WiFi devices a lot more than I do: > I am in the market for a small WiFi access point which I can use primarily to > connect a small Ethernet network to wireless devices (tablets, phones). This > is a trade show application - aka 2-3 Ethernet demo devices attached via > WiFi. I'm looking for small, light, and although battery would be nice > occasionally, "wall power" is a must, even if it is just leave it plugged > into the charger while operating. I'm going to be flying with this device so > I don't want something large and clunky. > Bonus for a device which will also act as a wifi client/nat router at the > same time.... aka act as a "WISP client" AND at the same time act as an AP. > Not sure if this exists or is even possible with current hardware..... If > not, if there's a teensy wisp client out there with ethernet for this type of > application, feel free to point me there... > My fallback position is probably a RB951, although the new hAP light product > is intriguing (not sure if it is even shipping yet). > -- > Forrest Christian CEO, PacketFlux Technologies, Inc. > Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 > [email protected]<mailto:[email protected]> | > http://www.packetflux.com<http://www.packetflux.com/> > [https://s3.amazonaws.com/images.wisestamp.com/icons/linkedin.png]<http://www.linkedin.com/in/fwchristian> > [https://s3.amazonaws.com/images.wisestamp.com/icons/facebook.png] > <http://facebook.com/packetflux> > [https://s3.amazonaws.com/images.wisestamp.com/icons/twitter.png] > <http://twitter.com/@packetflux> > -- > Forrest Christian CEO, PacketFlux Technologies, Inc. > Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 > [email protected]<mailto:[email protected]> | > http://www.packetflux.com<http://www.packetflux.com/> > [https://s3.amazonaws.com/images.wisestamp.com/icons/linkedin.png]<http://www.linkedin.com/in/fwchristian> > [https://s3.amazonaws.com/images.wisestamp.com/icons/facebook.png] > <http://facebook.com/packetflux> > [https://s3.amazonaws.com/images.wisestamp.com/icons/twitter.png] > <http://twitter.com/@packetflux> > -- > Forrest Christian CEO, PacketFlux Technologies, Inc. > Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 > [email protected]<mailto:[email protected]> | > http://www.packetflux.com<http://www.packetflux.com/> > [https://s3.amazonaws.com/images.wisestamp.com/icons/linkedin.png]<http://www.linkedin.com/in/fwchristian> > [https://s3.amazonaws.com/images.wisestamp.com/icons/facebook.png] > <http://facebook.com/packetflux> > [https://s3.amazonaws.com/images.wisestamp.com/icons/twitter.png] > <http://twitter.com/@packetflux>
