Ok, so that’s a physical thing? I had assumed that the radios/antennas could do the full 11GHz spectrum.
Does anyone know how to tell if this IP20C have to be physically or programmatically configured for high/low? I don’t see that in the docs. From: Af [mailto:af-boun...@afmug.com] On Behalf Of Ty Featherling Sent: Thursday, March 24, 2016 2:09 PM To: af@afmug.com Subject: Re: [AFMUG] Ceragon IP20C There should be a low side and a high side. One transmits at the higher frequency and the other lower. I found out if you have the low one set to transmit high it won't work. I can't remember on the ip20 but some ODUs can be rotated to switch from high to low. That may be what you did when you rotated that one side. -Ty -Ty On Mar 24, 2016 2:22 PM, "Sterling Jacobson" <sterl...@avative.net<mailto:sterl...@avative.net>> wrote: I’m not sure there is a parameter for that in this radio. I don’t see anything saying High or Low. I just see a tx/rx for each pair of radios in each side. Per Ceragon instructions those are the same tx/rx settings for both radios, just reversed on the other side. From: Af [mailto:af-boun...@afmug.com<mailto:af-boun...@afmug.com>] On Behalf Of Ty Featherling Sent: Thursday, March 24, 2016 1:18 PM To: af@afmug.com<mailto:af@afmug.com> Subject: Re: [AFMUG] Ceragon IP20C You changed channels, it it still the right unit? High vs low? -Ty -Ty On Thu, Mar 24, 2016 at 1:42 PM, Sterling Jacobson <sterl...@avative.net<mailto:sterl...@avative.net>> wrote: I'm checking, but yet, they should be. This link was up and working last year, then it was removed off the mountain, then this year put back up with one end in a different location and under a different FCC license. So the things that were changed were the tx/rx frequencies (matching send for both radios on a side and matching receive, just switched on each end) and dBm now on both sides. Physically on one side we 'rotated' the antenna/mount 180 degrees to make it a right handed mount instead of left handed. That shouldn't matter, should it? I don't have management access available externally, or even able to connect to the internet at this point in time, or I would. I could send screen shots I guess. -----Original Message----- From: Af [mailto:af-boun...@afmug.com<mailto:af-boun...@afmug.com>] On Behalf Of SmarterBroadband Sent: Thursday, March 24, 2016 12:36 PM To: af@afmug.com<mailto:af@afmug.com> Subject: Re: [AFMUG] Ceragon IP20C Are they on the same firmware? That caused us a problem where they would not link. Can you give me remote access? I could take a quick look and compare to one of my links. Adam -----Original Message----- From: Af [mailto:af-boun...@afmug.com<mailto:af-boun...@afmug.com>] On Behalf Of Sterling Jacobson Sent: Thursday, March 24, 2016 11:33 AM To: af@afmug.com<mailto:af@afmug.com> Subject: Re: [AFMUG] Ceragon IP20C Hey guys, I am completely stumped at this point. I've tried three times to get this link working, to even show a brief blip of anything showing up on the other side power wise. I have both radios ON and transmitting at full 24dBm. I don't see ANYTHING change on the other side of the link. This is with 3' dishes and about 8 miles out. All settings on both sides are the same except tx/rx frequencies swapped of course. What am I missing? Is there some magic on/off switch or feature/function that I am overlooking on these radios? GAAAHHHHH! -----Original Message----- From: Af [mailto:af-boun...@afmug.com<mailto:af-boun...@afmug.com>] On Behalf Of Sterling Jacobson Sent: Wednesday, February 24, 2016 2:13 PM To: 'af@afmug.com<mailto:af@afmug.com>' <af@afmug.com<mailto:af@afmug.com>> Subject: [AFMUG] Ceragon IP20C Anyone around today that has configured and aimed these before? I'm in the web page under Radio Parameters and I'm confused about the TX Mute. Should that be ON to allow the radios to talk? Or OFF? And I'm unsure on XPIC, I think I have it so it should work, but I only have a pair of frequencies, but two actual radios per side of this link.
