Make sure you are using the right settings in Torch.... and you can always sort on the DSCP Marks.
You should see something like in the attached picture... Faisal Imtiaz Snappy Internet & Telecom 7266 SW 48 Street Miami, FL 33155 Tel: 305 663 5518 x 232 Help-desk: (305)663-5518 Option 2 or Email: [email protected] > From: "Andreas Wiatowski" <[email protected]> > To: [email protected] > Sent: Wednesday, May 11, 2016 11:46:07 AM > Subject: Re: [AFMUG] Mikrotik Routers and VOIP QOS > I’ve been trying to see DSCP marks in torch on our CRR’s… can’t seem to see > anything in the interface. I’m going to try a packet capture and view in > Wireshark. > Thanks for your input. > Cheers, > ______________________________ > Andreas Wiatowski | CEO > Silo Wireless Inc. > Email [email protected] > 19 Sage Court > Brantford, Ontario N3R 7T4 (CANADA) > Tel +1.519.449.5656 Extension-600|Fax +1.519.449.5536 |Toll Free > +1.866.727.4138 > From: Af [mailto:[email protected]] On Behalf Of Faisal Imtiaz > Sent: Wednesday, May 11, 2016 10:48 AM > To: [email protected] > Subject: Re: [AFMUG] Mikrotik Routers and VOIP QOS > Andreas, > Yes, here is the logic.... > PBX should mark packets correctly (RTP packets as well as SIP signaling... for > packets going towards to the CPE). > Phone CPE should mark packets correctly... (for packets going to the PBX) > Routers typically are not constrained on their pipes, so traffic flows well. > Unless you are using some sort of queues to restrict traffic flow.... then you > have to make sure that dscp/qos marked traffic flows with priority. > Most radio's will respect DSCP/QoS marks and allocate priority accordingly... > (check with your radio mfg / firmware version, config etc). > BTW you can easily see the DSCP/QoS marks if you use TORCH on the MT, it is > real > time.... :) > Regards > Faisal Imtiaz > Snappy Internet & Telecom > 7266 SW 48 Street > Miami, FL 33155 > Tel: 305 663 5518 x 232 > Help-desk: (305)663-5518 Option 2 or Email: [email protected] >> From: "Andreas Wiatowski" < [email protected] > >> To: [email protected] >> Sent: Wednesday, May 11, 2016 10:17:03 AM >> Subject: Re: [AFMUG] Mikrotik Routers and VOIP QOS >> Faisal, >> So the packets should still contain DSCP tags regardless of layer2 or layer3? >> Sounds like I will need to do some packet captures. >> Cheers, >> ______________________________ >> Andreas Wiatowski | CEO >> Silo Wireless Inc. >> Email [email protected] >> 19 Sage Court >> Brantford, Ontario N3R 7T4 (CANADA) >> Tel +1.519.449.5656 Extension-600|Fax +1.519.449.5536 |Toll Free >> +1.866.727.4138 >> From: Af [ mailto:[email protected] ] On Behalf Of Faisal Imtiaz >> Sent: Wednesday, May 11, 2016 9:35 AM >> To: [email protected] >> Subject: Re: [AFMUG] Mikrotik Routers and VOIP QOS >> Hi Andreas, >> in our network, we handle this as follows:- >> 1) we make sure that the PBX is marking the packets with the DSCP tags >> correctly. >> 2) we make sure that the phone/iad are marking the packets with DSCP tags >> correctly. >> 3) we make sure that the Radios (AP & CPE) are using firmware that respects >> the >> DSCP Tags, and provides them with appropriate priority >> 4) we don't do anything on our routers (in our network). if we have to, the >> only >> thing we do on the customer router (Dmarc) is to make sure that the dscp tags >> are correct. >> And this works very well for us. >> Regards. >> Faisal Imtiaz >> Snappy Internet & Telecom >> 7266 SW 48 Street >> Miami, FL 33155 >> Tel: 305 663 5518 x 232 >> Help-desk: (305)663-5518 Option 2 or Email: [email protected] >>> From: "Andreas Wiatowski" < [email protected] > >>> To: [email protected] >>> Sent: Wednesday, May 11, 2016 1:39:36 AM >>> Subject: [AFMUG] Mikrotik Routers and VOIP QOS >>> Hello All! >>> We have about 90 sites primarily with CCR’s of various flavours. We have >>> yet to >>> implement any type of QOS for our VOIP..but we are starting to feel some >>> quality pain with a couple of our “ON NET” PBX/SIP products. >>> I have been reading about using mangle rules to mark connections and then >>> packets, then setting up a QUEUE tree in MT where the packet marks are >>> prioritized. We are fully routed with no layer 2 / bridging. I’m wondering >>> if I >>> can accomplish the same thing by just identifying the IP of my Multi-Tenant >>> PBX >>> box and any traffic moving to and from…and prioritizing it as 1. Secondly, >>> do I >>> have to do this on every single router on my network? >>> OR Is it a better practice to IDENTIFY DCSP or TOS, mark and prioritize that >>> instead. Just looking for the best way to unify this across my network. >>> Anyone have examples? Many of the examples I have seen really relate to SOHO >>> type situations…. We are talking much larger here. Most of my transport is >>> 200Mbps to 10Gbps between sites. >>> Cheers, >>> Andreas Wiatowski, CEO >>> Silo Wireless Inc. >>> 519-449-5656 x-600
