What I keep hearing from customers is that they want to run a multistrand cable up the tower and have an all in one box at the top which they terminate the cable into, hook up power to it, and then run short jumpers to their radios. I've heard this from enough different customers that it seems like a common desire.
They all seem to want the box to do media conversion and power injection and sync, with remote control and not much more. When quizzed about just doing a switch and an injector up top, they all expressed how this was unacceptable. At this point I'm looking at feasability. I'm not sure if this will ever see the light of day, a lot depends on the amount of R&D required. On Mar 31, 2017 7:07 AM, "Paul McCall" <[email protected]> wrote: > Forrest, > > > > For what it is worth, when we went Fiber (MST) up the tower, we run UBNT > S16s up there which is simple and working well, and GPS pucks on the ePMP, > or Syncbox 12 (or Junior) for devices that need sync. We have a handful of > 450s, 25 320s, and a dozen or so 900s where we use the SyncBox. > > > > Been very pleased so far with the reliability of the S16 POE. We VLAN APs > in one group and BH’s each on their own VLAN, and bring it down the fiber. > If we have other devices with fiber, we bring them down on their own fiber > (off the same MST). Of course there is core router with fiber inputs only > being used (with the exception of the sitemonitor which I may have to buy a > media converter for just to isolate the electrical connection into the > router. > > > > So, as far as anything up top, I would think it would have to be some form > of switch, or it would be quite kludgy. > > > > Paul > > > > *From:* Af [mailto:[email protected]] *On Behalf Of *Forrest Christian > (List Account) > *Sent:* Thursday, March 30, 2017 8:26 PM > *To:* af <[email protected]> > *Subject:* Re: [AFMUG] Gigabit ethernet converters? > > > > I've torn a couple apart that use a fairly easy to use chipset. But only > available in commercial temperature range. > > > > Some of the battle here is figuring out the vendors who do this type of > stuff. I want to avoid switches since I want this as transparent as > possible, but I might end up having to go there. I have another secret > weapon in my arsenal but I'm hoping I don't have to go there since that's > more software and software takes time. > > > > On Mar 30, 2017 2:21 PM, "Chuck McCown" <[email protected]> wrote: > > I looked at doing media converters last year. Not trivial. > > > > *From:* Forrest Christian (List Account) > > *Sent:* Thursday, March 30, 2017 2:07 PM > > *To:* af > > *Subject:* Re: [AFMUG] Gigabit ethernet converters? > > > > Yeah, maybe I should be clearer what I'm looking at. > > > > I'm looking at various options to build a tower-top box to simplify the > fiber up the tower with syncronized radios at the top.. Think a multiport > ubiquiti fiberpoe with sync over power and a gps receiver built in, along > with tower-top management. > > > > I don't want to include a switch up top - most people want as little as > possible up there, and I'd rather keep the whole thing as simple as > possible - I'd rather just use a copper-to-sfp chipset, but I haven't found > any which I feel comfortable integrating. So I need to tear some more of > the units apart to figure out what chipsets are available. > > > > -forrest > > > > On Thu, Mar 30, 2017 at 8:12 AM, Adam Moffett <[email protected]> wrote: > > RB260. > > Haven't had one fail due to cold yet that I know of. That's a switch, so > maybe it's more complicated than you're going for. > > > > > > ------ Original Message ------ > > From: "Forrest Christian (List Account)" <[email protected]> > > To: "af" <[email protected]> > > Sent: 3/30/2017 1:45:52 AM > > Subject: [AFMUG] Gigabit ethernet converters? > > > > I want to buy another selection of gigabit copper to sfp converters for > reverse engineering purposes. Ideally some which are known to work well > and especially any which don't fail in non climate controlled environments. > > > > What is everyone using? > > > > > > -- > > *Forrest Christian* *CEO, PacketFlux Technologies, Inc.* > > Tel: 406-449-3345 <(406)%20449-3345> | Address: 3577 Countryside Road, > Helena, MT 59602 > > [email protected] | http://www.packetflux.com > > <http://www.linkedin.com/in/fwchristian> <http://facebook.com/packetflux> > <http://twitter.com/@packetflux> > >
