The 450

On Sun, Sep 3, 2017, 11:38 AM Jay Weekley <[email protected]> wrote:

> I was wondering which signal was being killed.  The satellite or the 450.
>
> David Milholen wrote:
> >
> > What scenario would cause that using a 450 Mine is only 5 ft away with
> > no issues
> >
> >
> >
> > On 9/2/2017 12:50 AM, Timothy Steele wrote:
> >>
> >> Not sure about ubnt about dish and even more so direct TV cambium
> >> 450's will mess with signal normally kills the radio​ signal first
> >>
> >>
> >> On Fri, Sep 1, 2017, 1:09 PM Jeremy <[email protected]
> >> <mailto:[email protected]>> wrote:
> >>
> >>     All of the old M series, 5GHz & 2.4GHz had an underclocked
> >>     processor to avoid coming to close to the 2.4GHz frequency and
> >>     causing interference to co-located 2.4GHz radios.  As it turns
> >>     out, the third harmonic of the 2GHz frequency that they were
> >>     underclocked to would interfere with Verizon's 700MHz LTE gear.
> >>     So we have to run special (not underclocked) firmware on sites
> >>     where we co-locate with Verizon.  None of the new radios made in
> >>     the last few years have this issue, as they have a faster
> >>     processor.  They really didn't need to underclock them anyway.
> >>     We have 2.4GHz alongside of radios that had that special firmware
> >>     and they were not affected at all.
> >>
> >>     On Fri, Sep 1, 2017 at 1:44 PM, George Skorup
> >>     <[email protected] <mailto:[email protected]>> wrote:
> >>
> >>         Ethernet. Power it up, leave ethernet link down.
> >>
> >>         Switching power supply. Try battery power only, leave
> >>         ethernet link down.
> >>
> >>         CPU/SoC. Pretty much the end of the road. I remember a thread
> >>         from maybe a couple years ago where an UBNT radio was
> >>         interfering with VzW's uplink. I think UBNT did a special
> >>         firmware that changed the CPU freq. I don't remember which
> >>         radio that was.
> >>
> >>         I want to say the IF side of the Dish LNB can be between
> >>         500-2200MHz. The cables tied together is obviously not good.
> >>
> >>         You're probably better off just moving your radio and cable
> >>         to just be done with it.
> >>
> >>
> >>         On 9/1/2017 1:05 PM, Jay Weekley wrote:
> >>
> >>             Got a call from a guy in the field that says Dish moved
> >>             their equipment behind our 2.4 Airgrid and whenever our
> >>             radio is powered up the customer loses their high
> >>             definition channels.  Our cable and theirs are tie
> >>             wrapped together so I suggested that they power the radio
> >>             with their survey rig to see if some kind of interference
> >>             was involved. Any idea on what is causing this problem?
> >>             Other suggestions besides moving our radio?
> >>
> >>
> >>
> >
> >
> > <
> http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient
> >
> >       Virus-free. www.avg.com
> > <
> http://www.avg.com/email-signature?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=emailclient
> >
> >
> >
> > <#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
>
>

Reply via email to