Hello,

I own a Gigabyte GA-7N400-L1 AMD motherboard
(home page at:
http://www.giga-byte.com/MotherBoard/Products/Products_GA-7N400-L1.htm
detailed specs at:
http://www.giga-byte.com/MotherBoard/Products/Products_Spec_GA-7N400-L1.htm
full manual (PDF) available from:
http://www.giga-byte.com/Motherboard/Support/Manual/Manual_GA-7N400-L1.htm)

According to the specs (I'm trying to dig what I suspect to be
the important parts, I'm a total newbie when it comes to such level
of hardware):

1. Chipset is nVidia nForce2 SPP Memory/AGP/PCI controller (PAC)
2. nVidia nForce2 MCP Integrated Peripheral Controller (PSIPC)
3. On-Board sound:
   3.1 Realtek ALC650 CODEC
   3.2 Line Out/2 front speaker
   3.3 Line In/2 rear speaker (by s/w switch)
   3.4 Mic In/center & subwoofer (by s/w switch)
   3.5 SPDIF In/Out
   3.6 CD In/AUC In/Game port

(I'm just copying from the specs, 95% of the above doesn't make any
sense to me).

I tried to install alsa-source 0.9.6 on debian unstable (because that's
what's available as a debian package). kernel modules compilation works
fine (with "ALSA_CARDS=all" for a start) "alsa start" recognizes the
sound card as requiring the intel8x00 driver.

The output of "lsmod" is:
-------------------------------------------------------------------------
Module Size Used by Not tainted
snd-seq-oss 29632 0 (unused)
snd-seq-midi-event 3584 0 [snd-seq-oss]
snd-seq 38384 2 [snd-seq-oss snd-seq-midi-event]
snd-pcm-oss 38436 0 (unused)
snd-mixer-oss 13304 0 [snd-pcm-oss]
snd-intel8x0 18916 0
snd-pcm 60868 0 [snd-pcm-oss snd-intel8x0]
snd-timer 15140 0 [snd-seq snd-pcm]
snd-ac97-codec 40888 0 [snd-intel8x0]
snd-page-alloc 6164 0 [snd-intel8x0 snd-pcm]
snd-mpu401-uart 3600 0 [snd-intel8x0]
snd-rawmidi 14080 0 [snd-mpu401-uart]
snd-seq-device 4224 0 [snd-seq-oss snd-seq snd-rawmidi]
snd 30212 0 [snd-seq-oss snd-seq-midi-event snd-seq snd-pcm-oss snd-mixer-oss snd-intel8x0 snd-pcm snd-timer snd-ac97-codec snd-mpu401-uart snd-rawmidi snd-seq-device]
------------------------------------------------------------------------


relevant parts of "lspci -vvv" are:

------------------------------------------------------------------------
00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
Subsystem: Giga-byte Technology: Unknown device 0c11
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR
- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >
SERR- <PERR-
Latency: 0
Capabilities: [48] #08 [01e1]


00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
Subsystem: Giga-byte Technology: Unknown device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR
- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >
SERR- <PERR-
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at c000 [size=32]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-



00:06.0 Multimedia audio controller: nVidia Corporation nForce2 AC97 Audio Controler (MCP)
(rev a1)
Subsystem: nVidia Corporation: Unknown device 4144
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR
- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >
SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at b000 [size=256]
Region 1: I/O ports at b400 [size=128]
Region 2: Memory at e0001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-


-----------------------------------------------------------------------

simply running "aplay" with this setup or any other sound program
results in the program playing as if everything is ok but no sound
comes out.
I ran alsamixer and unmuted and raised the volume for all channels.

What else can I do? Is this hardware supposed to be supported?

Thanks very much,

--Amos




------------------------------------------------------- This SF.net email is sponsored by: The SF.net Donation Program. Do you like what SourceForge.net is doing for the Open Source Community? Make a contribution, and help us add new features and functionality. Click here: http://sourceforge.net/donate/ _______________________________________________ Alsa-user mailing list [EMAIL PROTECTED] https://lists.sourceforge.net/lists/listinfo/alsa-user

Reply via email to