I think use the fresh kernel suited for ZOOM3. Try to give the proper details about the issue.
Regards, Jagan. On Tue, Dec 13, 2011 at 8:03 PM, Ismail <ismail.mohtas...@gmail.com> wrote: > Amar Nath <amarnath.revanna <at> gmail.com> writes: > > > > > Hi Sri, > > > > "Starting kernel..." is indeed the last message that u-boot prints > > just before jumping to > > the kernel entry point, so my understanding is that the your u-boot is > > working just fine. > > > > However, if your uImage is generated with a wrong entry point address > > than what the > > kernel is compiled for, its very much possible that your kernel > > doesn't get executed at all. > > > > I would have first checked if the "Entry Point" address printed by > > u-boot just before > > printing "Starting kernel..." closely matches to the corresponding > > _stext virtual address > > in the System.map file, generated in your kernel directory after the > build. > > > > As an example, lets say your system has a RAM memory bank mapped at > phys. addr > > 0x80000000 and in your kernel its been mapped to a virtual address of > > 0xC0000000. > > > > In this case, if the "Entry Point" address printed by u-boot is > > 0x80008000, you need to > > ensure _stext has address 0xC0008000 assigned to it in the System.map > > file (Note that > > the offset value '8000' matches here). > > > > If there is a mismatch here, u-boot would be jumping to an invalid > > address where it could > > not find the entry point to your kernel image and hence would fail to > boot. > > > > Hope this helps. > > > > BR, > > -Amar > > > > On Thu, Sep 9, 2010 at 10:39 AM, sri <sresindhu <at> gmail.com> wrote: > > > > > > Hi , > > > > > > @Sreekanth > > > > > > I have placed debug msgs in u-boot till the place it jumps to kernel > > > and it is fine. > > > And I am not getting "Uncompressing Linux...done, booting the kernel." > > > This msg is from kernel right. > > > my uart configuration looks fine. I have used same uart config as that > > > of working kernel. > > > > > > Steps I follow is: > > > > > > Place uImage in sdcard and then connect to board and pc using usb and > > > try to load uImage using minicom. > > > > > > @ simon, > > > my fs also looks fine. > > > > > > Thanks, > > > Sri. > > > > > > -- > > > unsubscribe: android-kernel+unsubscribe <at> googlegroups.com > > > website: http://groups.google.com/group/android-kernel > > > > Hi Amar, > the _stext address in my System.map shows c0008000 > c0004000 A swapper_pg_dir > c0008000 T __init_begin > c0008000 T _sinittext > c0008000 T _stext > c0008000 T stext > c0008034 t __enable_mmu > c0008060 t __turn_mmu_on > c0008078 t __create_page_tables > c0008124 t __switch_data > c000814c t __mmap_switched > c0008194 t __error_p > c00081b0 t str_p1 > c00081e7 t str_p2 > c00081ec t __error_a > > The zoom3 board is powercyling again and agian.The last debug message > before > powercycle is : > Uncompressing Linux... done, booting the kernel. > On reset the uboot logs is seen again: > U-Boot 1.1.4-ge891bbac-dirty (Mar 18 2010 - 17:47:41) > > OMAP3630-GP rev 1, CPU-OPP2 L3-200MHz > OMAP3630Zoom3 1.0 Version + mDDR (Boot NAND) > DRAM: 1024 MB > NAND:512 MiB > > > In: serial > Out: serial > Err: serial > Battery levels: main 3951 mV, backup 3078 mV > Hit any key to stop autoboot > > > Can you figure out what could be the issue. > Thanks, > Ismail > > > -- > unsubscribe: android-kernel+unsubscr...@googlegroups.com > website: http://groups.google.com/group/android-kernel -- unsubscribe: android-kernel+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-kernel