Hi, "Failed to execute /init. Attempting defaults..." -- is this the actual error ? check your file-system / bootargs. try and pass /bin/sh to init as a try-out and then go-ahead with passing a more complicated /init !!
regards, Pavan On Fri, Sep 11, 2009 at 12:17 PM, Kaushik(ICMAN) <kaushikprajap...@gmail.com> wrote: > I am also getting the same error. Is there any solution for this?? > -Kaushik > > On Thu, Sep 10, 2009 at 11:39 PM, sany <laurelsgal...@gmail.com> wrote: >> >> Hi, >> >> I am getting the following error when i try to port the Kernel image i >> obtained through the following link, >> >> git://labs.embinux.org/repo/android/platform/omap3manifest.git. >> >> >> > Image Type: ARM Linux Kernel Image (uncompressed) >> > Data Size: 2075720 Bytes = 2 MB >> > Load Address: 80008000 >> > Entry Point: 80008000 >> > Verifying Checksum ... OK >> > Loading Kernel Image ... OK >> > OK >> > >> > Starting kernel ... >> > >> > Uncompressing >> > Linux............................................................. >> > >> > ......................................................................... >> > done, >> > booting the kernel. >> > Linux version 2.6.29-omap1-07255-g85f0546 (r...@localhost.localdomain) ( >> > For any >> > Queries, information and bug reports please mail to o...@embinux.com ) >> > #1 Thu Se >> > p 10 18:54:14 IST 2009 >> > CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=10c5387f >> > CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache >> > Machine: OMAP3 Beagle Board >> > Memory policy: ECC disabled, Data cache writeback >> > OMAP3430 ES2.1 >> > SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000 >> > Reserving 12582912 bytes SDRAM for VRAM >> > Built 1 zonelists in Zone order, mobility grouping on. Total pages: >> > 32512 >> > Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/mmcblk0p2 >> > video=o >> > mapfb.mode=dvi:1280x720mr...@50 init=/init rootfstype=ext3 rw >> > rootdelay=1 nohz=o >> > ff androidboot.console=ttyS2 >> > Unknown boot option `androidboot.console=ttyS2': ignoring >> > Clocking rate (Crystal/DPLL/ARM core): 26.0/332/500 MHz >> > GPMC revision 5.0 >> > IRQ: Found an INTC at 0xd8200000 (revision 4.0) with 96 interrupts >> > Total of 96 interrupts on 1 active controller >> > OMAP34xx GPIO hardware version 2.5 >> > PID hash table entries: 512 (order: 9, 2048 by >> > OMAP clockevent source: GPTIMER12 at 32768 Hz >> > Console: colour dummy device 80x30 >> > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) >> > Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) >> > Memory: 128MB = 128MB total >> > Memory: 112768KB available (3824K code, 718K data, 144K init) >> > Calibrating delay loop... 484.21 BogoMIPS (lpj=1892352) >> > Mount-cache hash table entries: 512 >> > CPU: Testing write buffer coherency: ok >> > net_namespace: 520 bytes >> > regulator: core version 0.5 >> > NET: Registered protocol family 16 >> > Found NAND on CS0 >> > Registering NAND on CS0 >> > OMAP DMA hardware revision 4.0 >> > bio: create slab <bio-0> at 0 >> > OMAP DSS rev 2.0 >> > OMAP DISPC rev 3.0 >> > OMAP VENC rev 2 >> > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHz >> > twl4030: PIH (irq 7) chaining IRQs 368..375 >> > twl4030: power (irq 373) chaining IRQs 376..383 >> > twl4030: gpio (irq 368) chaining IRQs 384..401 >> > regulator: VMMC1: 1850 <--> 3150 mV normal standby >> > regulator: VDAC: 1800 mV normal standby >> > regulator: VUSB1V5: 1500 <--> 0 mV normal standby >> > regulator: VUSB1V8: 1800 <--> 0 mV no >> > regulator: VUSB3V1: 3100 <--> 0 mV normal standby >> > regulator: VPLL2: 1800 mV normal standby >> > regulator: VSIM: 1800 <--> 3000 mV normal standby >> > i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz >> > SCSI subsystem initialized >> > twl4030_usb twl4030_usb: Initialized TWL4030 USB module >> > usbcore: registered new interface driver usbfs >> > usbcore: registered new interface driver hub >> > usbcore: registered new device driver usb >> > musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0 >> > musb_hdrc: USB OTG mode controller at d80ab000 u >> > NET: Registered protocol family 2 >> > IP route cache hash table entries: 1024 (order: 0, 4096 bytes) >> > TCP established hash table entries: 4096 (order: 3, 32768 bytes) >> > TCP bind hash table entries: 4096 (order: 2, 16384 bytes) >> > TCP: Hash tables configured (established 4096 bind 4096) >> > TCP reno registered >> > NET: Registered protocol family 1 >> > NetWinder Floating Point Emulator V0.97 (double precision) >> > ashmem: initialized >> > VFS: Disk quotas dquot_6.5.2 >> > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) >> > JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. >> > msgmni has been set to 220 >> > alg: No test for stdrng (krng) >> > io scheduler noop registered >> > io scheduler anticipatory registered (default) >> > io scheduler deadline registered >> > io scheduler cfq registered >> > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled >> > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654 >> > serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 >> > serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 >> > console [ttyS2] enabled >> > brd: module loaded >> > loop: module loaded >> > i2c /dev entries driver >> > Driver 'sd' needs updating - please use bus_type methods >> > omap2-nand driver initializing >> > NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB >> > 1,8V 16-bi >> > t) >> > cmdlinepart partition parsing not available >> > Creating 5 MTD partitions on "omap2-nand": >> > 0x000000000000-0x000000080000 : "X-Loader" >> > 0x000000080000-0x000000260000 : "U-Boot" >> > 0x000000260000-0x000000280000 : "U-Boot Env" >> > 0x000000280000-0x000000680000 : "Kernel" >> > 0x000000680000-0x0000100000 >> > usbmon: debugfs is not available >> > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >> > ehci-omap ehci-omap.0: OMAP-EHCI Host Controller >> > ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1 >> > ehci-omap ehci-omap.0: irq 77, io mem 0x48064800 >> > ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00 >> > usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 >> > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 >> > usb usb1: Product: OMAP-EHCI Host Controller >> > usb usb1: Manufacturer: Linux 2.6. >> > usb usb1: SerialNumber: ehci-omap.0 >> > Start >> > usb usb1: configuration #1 chosen from 1 choiceU-Boot 1.3.3 (Jul 10 2008 >> > - 16:33:09) >> > hub 1-0:1.0: USB hub found >> > >> > OMAP3530-GP rev 2, CPU-O >> > hub 1-0:1.0: 3 ports detected >> > OMAP3 Be >> > Initializing USB Mass Storage driver... >> > DRAM: 128 MB >> > usbcore: registered new interface driver usb-storage >> > Out: serial >> > Err: serial >> > USB Mass Storage support registered.omplete >> > android initny key to st >> > android_bind 0 >> > mass_storage_function_addP3 beagleboard.org # sete >> > android_usb gadget: Number of LUNs=1e: >> > setenv - set environment v >> > adb_function_add >> > android_usb gadget: android_usb readyootargs >> > musb_hdrc musb_hdrc: MUSB HDRC host driver >> > OMAP3 >> > musb_hdrc musb_hdrc: new USB bus registered, assigned bus numtry 'help' >> > >> > usbcore: registered new interface driver usbhid >> > usbhid: v2.6:USB HID core driverin variable name "bootargs=conso >> > logger: created 64K log 'log_main' >> > logger: created 256K log 'log_events' beagleboard.org # setenv bootargs >> > logger: created 64K log 'log_radio' >> > Unknown command 'setenv' - try 'he >> > Advanced Linux Sound Architecture Driver Version 1.0.18a..org # setenv >> > bootargs=console=ttyS2,115200n8 noinitrd ro >> > No device for DAI AD73311 >> > No device for DAI AK4535 >> > v/mmcblk0p2 v >> > No device for DAI cs4270x720mr...@50 init=/init >> > No device for DAI PCM3008 HiFi >> > No device for DAI SSM2602 >> > rootdelay=1 >> > No device for DAI tlv320aic23tyS2 >> > No device for DAI tlv320aic3xr: illegal character '=' in v >> > No device for DAI twl4030sole=ttyS2,115200n >> > No device for DAI UDA134X >> > No device for DAI UDA1380 >> > >> > No device for DAI WM8580 PAIFTX >> > No device for DAI WM8728 >> > rootdelay=1 >> > No device for DAI WM8731ole=ttyS2 >> > No device for DAI WM8750 >> > OMAP3 beagleboar >> > No device for DAI WM8753 DAI 0 >> > Saving Environ >> > No device for DAI WM8753 DAI 1 >> > Erasing Nand...W >> > No device for DAI WM8971 >> > No device for DAI WM8990 ADC/DAC Primaryenv >> > file >> > No device for DAI omap-mcbsp-dai-0mmcinit;fatload mmc 0 0x80300000 u >> > No device for DAI omap-mcbsp-dai-1 >> > No device for DAI omap-mcbsp-dai-2 >> > stdout=serial >> > No device for DAI omap-mcbsp-dai-3s=console=ttyS2,115200n8 noinitrd >> > No device for DAI omap-mcbsp-da >> > OMAP3 be >> > TCP cubic registered >> > >> > T >> > NET: Registered protocol family 17 >> > Startin >> > NET: Registered protocol family 15 >> > >> > >> > U-Boot 1.3.3 (Jul 10 20 >> > RPC: Registered udp transport module. >> > >> > OMAP3530-GP rev 2, CPU >> > RPC: Registered tcp transport module. >> > OMAP3 Beagle Board + L >> > Power Management for TI OMAP3. >> > DRAM: 128 MB >> > VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev >> > 1rial >> > Err: serial >> > Audio Tone on Speakers .. >> > Console: switching to colour frame buffer device 80x30key to stop >> > autoboot: 0 >> > clock: clksel_round_rate_div: dpll4_m4_ck target_rate 3 >> > >> > Freeing init memory: 144K1 Thu Se >> > Warning: unable to open an initial console. >> > p 10 18:54:14 IST 2009 >> > Failed to execute /init. Attempting defaults...082] revision 2 (ARMv7), >> > cr=10c5387f >> > Kernel panic - not syncing: No init found. Try passing init= option to >> > kernel.ache, VIPT nonaliasing instruction cache >> > android_usb gadget: high speed config #1: androide Board >> > Memory policy: >> > android_usb gadget: high speed config #1: android >> > OMAP3430 ES2.1 >> > android_usb gadget: high speed config #1: androidd7000000 size: 0x100000 >> > >> > >> > Texas Instruments X-Loader 1.41eserving 12582912 bytes SDRAM f >> > Starting OS Bootloader... >> > >> > >> > >> > DRAM: 128 MB=o >> > NAND: 256 MiB >> > In: serial >> > Out: serialmapfb.mode=dv >> > Err: seri...@50 init=/in >> > Audio Tone on Speakers ... completez=o >> > Hit any key to stop autoboot: 0 >> > ff androidboot.co >> > reading uImage >> > >> > 2075784 bytes readoot option `androi >> > ## Booting kernel from Legacy Image at 80300000 ... >> > Clocking rate ( >> > Image Name: Linux-2.6.29-omap1-07255-g85f054 >> > GPM >> > Image Type: ARM Linux Kernel Image (uncompressed)xd8200000 >> > (revision 4.0) with 96 interrupts >> > Data Size: 2075720 Bytes = 2 MB >> > Total of 96 interrupt >> > Load Address: 80008000 >> > Entry Point: >> > >> > Uncompressing >> > Linux............................................................. >> > Console: colour dummy device 80x30 >> > >> > ......................................................................... >> > done, >> > Inode-cache hash table entri >> > booting the kernel.32768 bytes) >> > Linux version 2.6.29-omap1-07255-g85f0546 (r...@localhost.localdomain) ( >> > For any >> > Memory: 112768KB available (3824K code, 718K data, 1 >> > Queries, information and bug reports please mail to o...@embinux.com ) >> > #1 Thu Seg delay loop... 483.16 BogoMIPS (lpj=1888256) >> > p 10 18:54:14 IST 2009unt-cache hash table e >> > CPU: ARMv7 Processor [411fc082] revision 2 (ARMv7), cr=10c5387fe buffer >> > coherency: ok >> > >> > Memory policy: ECC disabled, Data cache writeback >> > OMAP DMA hardware revision 4.0 >> > OMAP3430 ES2.1 >> > bio >> > SRAM: Mapped pa 0x40200000 to va 0xd7000000 size: 0x100000P DSS rev 2.0 >> > OMAP DISPC rev 3.0 >> > Reserving 12582912 bytes SDRAM for VRAMi2c_omap i2c_omap.1: bus 1 >> > rev3.12 at 2 >> > Built 1 zonelists in Zone order, mobility grouping on. Total pages: >> > 32512chaining IRQs 368..375 >> > twl4030: >> > Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/mmcblk0p2 >> > video=o >> > twl4030: gpio (irq 368) chaining IRQs 384..401 >> > mapfb.mode=dvi:1280x720mr...@50 init=/init rootfstype=ext3 rw >> > rootdelay=1 nohz=o >> > regulator: VDAC: 1800 mV normal standby >> > ff androidboot.cons >> > i2c_oma >> > OMAP34xx GPIO hardware version 2.5kHz >> > PID hash table entries: 512 (order: 9, 2048 bytes) >> > twl4030_usb twl4030_usb: Initiali >> > OMAP clockevent source: GPTIMER12 at 32768 Hz >> > usbcore: regi >> > Console: colour dummy device 80x30 >> > Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) >> > usbcore: registered new d >> > Inode-cache hash table entries: 8192 (orde >> > >> > net_namespace: 520 bytesed hash table entries: 4 >> > regulator: core version 0.5 >> > NET: Registered protocol family 16 >> > TCP bind hash table entries: 409 >> > Found NAND on CS0 bytes) >> > Registering NAND on CS0 >> > OMAP DMA hardware revision 4.0stablished 4096 bind 4096) >> > bio: create slab <bio-0> at 0 >> > TCP re >> > OMAP DSS rev 2.0 >> > >> > OMAP DISPC rev 3.0tocol family 1 >> > OMAP VENC rev 2 >> > N >> > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 kHzprecisio >> > regulator: VUSB1V5: 1500 <--> 0 mV normal standbyticipatory registered >> > (default) >> > regulator: VUSB1V8: 1800 <--> 0 mV normal standby registered >> > io sc >> > regulator: VUSB3V1: 3100 <--> 0 mV normal standbySerial: 8250/16550 >> > driver, 4 ports, IRQ sharing e >> > regulator: VPLL2: 1800 mV normal standby >> > serial8250.0: ttyS0 >> > regulator: VSIM: 1800 <--> 3000 mV normal standby >> > i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 kHz(irq >> > i2c /dev >> > usbcore: registered new interface driver hub 'sd' needs updating - >> > please use bus_type m >> > usbcore: registered new device driver usb >> > omap2-nand driver in >> > musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), debug=0r ID: >> > 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V 16-bi >> > musb_hdrc: USB OTG mode controller at d80ab000 using DMA, IRQ 92 >> > t) >> > cmdlinepart partition parsing not available >> > NET: Registered protocol family 2 >> > Creating 5 MTD partitions on "o >> > IP route cache hash table entries: 1024 (order: 0, 4096 >> > bytes)00000-0x000000080000 : "X-Loader" >> > TCP established hash table entries: 4096 (order: 3, 32768 bytes) >> > 0x000000260000-0x000000280 >> > ashmem: initialized.0: new USB bus reg >> > VFS: Disk quotas dquot_6.5.21 >> > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)ap.0: irq 77, >> > io mem 0x48064800 >> > JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.started, EHCI 1.00 >> > msgmni has been set to 220ew USB device found, idVen >> > alg: No test for stdrng (krng) >> > io scheduler noop registeredusb1: New USB device strings >> > io scheduler anticipatory registered (defa >> > Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled >> > usb usb1 >> > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a ST16654usb usb1: >> > configuration #1 chosen from 1 choice >> > serial8250.0: ttyS1 at MMIO 0x4806c000 (irq = 73) is a ST16654 >> > hub 1-0:1.0: 3 ports detected >> > serial8250.0: ttyS2 at MMIO 0x49020000 (irq = 74) is a ST16654 >> > usbcore: registered new in >> > console [ttyS2] enabledge >> > brd: module loaded >> > USB M >> > loop: module loadedregistered. >> > i2c /dev entries driver >> > android init >> > Driver 'sd' needs updating - please use bus_type methods >> > android_usb gadget: Number of >> > omap2-nand driver initializing >> > adb_function_add >> > 0x000000080000-0x000000260000 : "U-Boot" >> > usb usb2: Product: MUSB HDRC >> > 0x000000260000-0x000000280000 : "U-Boot Env" >> > usb usb2: Manufacturer: Linux 2.6.29- >> > 0x000000280000-0x000000680000 : "Kernel" >> > 0x000000680000-0x000010000000 : "File System"rc >> > usb usb2: >> > usbmon: debugfs is not availablehoice >> > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver >> > hub 2-0:1.0: 1 port detected >> > ehci-omap ehci-omap.0: OMAP-EHCI Host C >> > usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 >> > logger: created 64K log 'log_radio' >> > usb usb1: Product: OMAP-EHCI Host Controllerux Sound Architecture Driver >> > Version 1.0.18a >> > usb usb1: Manufacturer: Linux 2.6.29-omap1-07255-g85f0546 ehci_hcde for >> > DAI AD73311 >> > No device for DAI AK453 >> > usb usb1: SerialNumber: ehci-omap.0for DAI CS4270 >> > usb usb1: configuration #1 chosen from 1 choice >> > No device for DAI SSM2602 >> > hub 1-0:1.0: USB hub fou >> > USB Mass Storage support registered.e for DAI UDA1380 >> > android initice for DAI >> > android_bind >> > mass_storage_function_addWM8510 HiFi >> > android_usb gadget: Number of LUNs=1580 PAIFRX >> > adb_function_addor DAI WM8580 PA >> > android_usb gadget: android_usb ready device for DAI WM8728 >> > musb_hdrc musb_hdrc: MUSB HDRC host driver >> > No device for DAI WM8750 >> > musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 2 >> > No device for DAI WM8753 DAI 1 >> > usb usb2: New USB device found, idVendor=1d6b, idProduct=0002o device >> > for DAI WM8990 ADC/DAC Primary >> > usb usb2: New USB device strings: Mfr=3, Prbsp-dai-0 >> > usb usb2: SerialNumber: musb_hdrc >> > OMAP >> > usb usb2: configuration #1 chosen from 1 choiceudio Codec init >> > asoc: t >> > hub 2-0:1.0: USB hub found mapping ok >> > hub 2-0:1.0: 1 port detected >> > ALSA device list: >> > twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as rtc0P cubic >> > registered >> > NET: Registered protocol f >> > twl4030_rtc twl4030_rtc: Power up reset detected.gistered protocol >> > family 15 >> > twl4030_rtc twl4030_rtc: Enabling TWL4030-RTC.le. >> > RPC: >> > mmci-omap-hs mmci-omap-hs.0: Failed to get debounce clock >> > Power Management for TI OMAP3. >> > usbcore: registered new interface driver usbhid architectu >> > No device for DAI CS42702000-01-01 00:06:40 UTC >> > No device for DAI PCM3008 HiFi >> > No device for DAI SSM2602 >> > 200) >> > Waiting 1sec be >> > No device for DAI tlv320aic23 >> > No device for DAI tlv320aic3xeed SD card at address b368 >> > No device for DAI twl4030 >> > mmcblk0: >> > No device for DAI UDA134X >> > No device for DAI UDA1380 >> > android_usb >> > No device for DAI UDA1380#1: android >> > No device for DAI UDA13 >> > >> > EXT3-fs: >> > No device for DAI WM8731ordered data mode. >> > No device for DAI WM8750 >> > VFS >> > No device for DAI WM8753 DAI 0) on device 179:2. >> > No device for DAI WM8753 DAI 1 >> > Freeing init memory: >> > No device for DAI WM8971 >> > Warning: unable to >> > No device for DAI WM8990 ADC/DAC Primary >> > Failed to ex >> > No device for DAI omap-mcbsp-dai-0. >> > No device for DAI omap-mcbsp-dai-1syncing: No init found. Try passi >> > No device for DAI omap-mcbsp-dai-2 >> > No device for DAI omap-mcbsp-dai-3 >> > android_usb gadget: high speed c >> > No device for DAI omap-mcbsp-dai-4 >> > an >> > OMAP3 Beagle SoC init speed config #1: and >> > TWL4030 Audio Codec init >> > TWL4030 Audio Codec init >> > Console: switching to colour frame buffer device 80x30 >> > clock: clksel_round_rate_div: dpll4_m4_ck target_rate 36000000 >> > clock: new_div = 12, new_rate = 36000000 >> > omapdss: Could not find exact pixel clock. Requested 23500 kHz, got >> > 24000 kHz >> > twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC >> > (946684 >> > 800) >> > Waiting 1sec before mounting root device... >> > mmc0: new high speed SD card at address b368 >> > mmcblk0: mmc0:b368 SD 1.88 GiB >> > mmcblk0: p1 p2 >> > android_usb gadget: high speed config #1: android >> > kjournald starting. Commit interval 5 seconds >> > EXT3 FS on mmcblk0p2, internal journal >> > EXT3-fs: recovery complete. >> > EXT3-fs: mounted filesystem with ordered data mode. >> > VFS: Mounted root (ext3 filesystem) on device 179:2. >> > Freeing init memory: 144K >> > Warning: unable to open an initial console. >> > Failed to execute /init. Attempting defaults... >> > Kernel panic - not syncing: No init found. Try passing init= option to >> > kernel. >> > android_usb gadget: high speed config #1: android >> > android_usb gadget: high speed config #1: android >> > android_usb gadget: high speed config #1: android >> >> Please help! >> > > > > -- > With Regards, > Kaushik Prajapati > Grad. Student > San Jose State Uni. > 408-821-5891 > Ted Turner - "Sports is like a war without the killing." > > > -- --Pavan Savoy --~--~---------~--~----~------------~-------~--~----~ unsubscribe: android-porting+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-porting -~----------~----~----~----~------~----~------~--~---
