You want "init=/init" in your bootargs..and you can use "rootwait" instead of "rootdelay=3"..
Regards -- Ashwin On Sun, Jun 27, 2010 at 2:54 AM, Ranganath s <rangana...@gmail.com> wrote: > Hi, > I got it my previous kernel panic problem solved. Now i am able to mount > till rootfs but after that i am again running into "Kernel panic - not > syncing: Attempted to kill init!" > The boot log is as follows:- > > U-Boot 1.3.2-mini2440 (Oct 6 2009 - 12:51:09) > I2C: ready > DRAM: 64 MB > Flash: 2 MB > NAND: 128 MiB > Found Environment offset in OOB.. > USB: S3C2410 USB Deviced > In: serial > Out: serial > Err: serial > MAC: 08:00:2f:00:00:06 > Hit any key to stop autoboot: 0 > trying to detect SD Card... > Manufacturer: 0x1b, OEM "SM" > Product name: "SD ", revision 1.0 > Serial number: 3927984417 > Manufacturing date: 2/2010 > CRC: 0x4e, b0 = 1 > READ_BL_LEN=15, C_SIZE_MULT=7, C_SIZE=3453 > size = 2329935872 > 2060420 bytes read > ## Booting kernel from Legacy Image at 31000000 ... > Image Name: > Created: 2010-03-26 5:54:15 UTC > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 2060356 Bytes = 2 MB > Load Address: 30008000 > Entry Point: 30008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > Starting kernel ... > Uncompressing > Linux..................................................................................................................................... > done, booting the kernel. > Linux version 2.6.27 (r...@tom) (gcc version 4.3.2 (Sourcery G++ Lite > 2008q3-72) ) #1 PREEMPT Mon Aug 24 17:01:35 CST 2009 > CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177 > Machine: FriendlyARM Mini2440 development board > Memory policy: ECC disabled, Data cache writeback > CPU S3C2440A (id 0x32440001) > MM: CPU does not support supersection mapping for 0x55000000000 at > 0xf0d00000 > S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz > S3C24XX Clocks, (c) 2004 Simtec Electronics > CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on > CPU0: D VIVT write-back cache > CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets > CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets > Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 > Kernel command line: console=ttySAC0,115200 root=/dev/mmcblk0p3 > rootfstype=ext3 mini2440=1tb rootdelay=3 init=/linuxrc > irq: clearing pending status 02000000 > irq: clearing subpending status 00000002 > PID hash table entries: 256 (order: 8, 1024 bytes) > timer tcon=00500000, tcnt a4ca, tcfg 00000200,00000000, usec 00001e57 > Console: colour dummy device 80x30 > console [ttySAC0] enabled > Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) > Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) > Memory: 64MB = 64MB total > Memory: 60188KB available (3896K code, 636K data, 116K init) > SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 > Calibrating delay loop... 201.93 BogoMIPS (lpj=504832) > Mount-cache hash table entries: 512 > CPU: Testing write buffer coherency: ok > net_namespace: 288 bytes > NET: Registered protocol family 16 > S3C2440: Initialising architecture > S3C2440: IRQ Support > S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics > DMA channel 0 at c4800000, irq 33 > DMA channel 1 at c4800040, irq 34 > DMA channel 2 at c4800080, irq 35 > DMA channel 3 at c48000c0, irq 36 > S3C244X: Clock Support, DVS off > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > NET: Registered protocol family 2 > IP route cache hash table entries: 1024 (order: 0, 4096 bytes) > TCP established hash table entries: 2048 (order: 2, 16384 bytes) > TCP bind hash table entries: 2048 (order: 1, 8192 bytes) > TCP: Hash tables configured (established 2048 bind 2048) > TCP reno registered > NET: Registered protocol family 1 > NetWinder Floating Point Emulator V0.97 (double precision) > ashmem: initialized > NTFS driver 2.1.29 [Flags: R/W DEBUG]. > yaffs Aug 24 2009 16:57:57 Installing. > msgmni has been set to 117 > io scheduler noop registered (default) > Console: switching to colour frame buffer device 30x20 > fb0: s3c2410fb frame buffer device > adc initialized > input: buttons as /class/input/input0 > buttons initialized > leds initialized > s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440 > s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440 > s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440 > brd: module loaded > loop: module loaded > nbd: registered device at major 43 > logger: created 64K log 'log_main' > logger: created 256K log 'log_events' > logger: created 64K log 'log_radio' > dm9000 Ethernet Driver, V1.31 > Now use the default MAC address: 08:90:90:90:90:90 > eth0: dm9000e at c4804000,c4806004 IRQ 51 MAC: c3908934 (friendly-arm) > usbcore: registered new interface driver zd1211rw > usbcore: registered new interface driver zd1201 > Linux video capture interface: v2.00 > ovcamchip: v2.27 for Linux 2.6 : OV camera chip I2C driver > usbcore: registered new interface driver ov511 > ov511: v1.64 for Linux 2.5 : ov511 USB Camera Driver > Driver 'sd' needs updating - please use bus_type methods > S3C24XX NAND Driver, (c) 2004 Simtec Electronics > s3c2440-nand s3c2440-nand: Tacls=3, 29ns Twrph0=7 69ns, Twrph1=3 29ns > NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V > 8-bit) > NAND_ECC_NONE selected by board driver. This is not recommended !! > Scanning device for bad blocks > Creating 4 MTD partitions on "NAND 128MiB 3,3V 8-bit": > 0x00000000-0x00060000 : "supervivi" > 0x00060000-0x00260000 : "Kernel" > 0x00260000-0x40260000 : "root" > mtd: partition "root" extends beyond the end of device "NAND 128MiB 3,3V > 8-bit" -- size truncated to 0x7da0000 > 0x00000000-0x40000000 : "nand" > mtd: partition "nand" extends beyond the end of device "NAND 128MiB 3,3V > 8-bit" -- size truncated to 0x8000000 > s3c2410-ohci s3c2410-ohci: S3C24XX OHCI > s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1 > s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000 > usb usb1: configuration #1 chosen from 1 choice > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 2 ports detected > Initializing USB Mass Storage driver... > usbcore: registered new interface driver usb-storage > USB Mass Storage support registered. > s3c2440-usbgadget s3c2440-usbgadget: S3C2440: increasing FIFO to 128 bytes > mice: PS/2 mouse device common for all mice > usbcore: registered new interface driver appletouch > input: s3c2410 TouchScreen as /class/input/input1 > s3c2410 TouchScreen successfully loaded > S3C24XX RTC, (c) 2004,2006 Simtec Electronics > s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling > s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0 > i2c /dev entries driver > s3c2440-i2c s3c2440-i2c: slave address 0x10 > s3c2440-i2c s3c2440-i2c: bus frequency set to 98 KHz > s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter > mapped channel 0 to 0 > s3c2440-sdi s3c2440-sdi: powered down. > s3c2440-sdi s3c2440-sdi: initialisation done. > s3c2440-sdi s3c2440-sdi: running at 0kHz (requested: 0kHz). > s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz). > s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz). > s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz). > usbcore: registered new interface driver hiddev > s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz). > s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz). > s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz). > usbcore: registered new interface driver usbhid > usbhid: v2.6:USB HID core driver > UDA1341 audio driver initialized > failed to get memory region resouce > s3c2410-iis: probe of s3c2410-iis.0 failed with error -2 > TCP cubic registered > NET: Registered protocol family 17 > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > s3c2440-sdi s3c2440-sdi: running at 198kHz (requested: 197kHz). > s3c2440-sdi s3c2440-sdi: running at 16875kHz (requested: 25000kHz). > s3c2440-sdi s3c2440-sdi: running at 16875kHz (requested: 25000kHz). > mmc0: new SD card at address b368 > mmcblk0: mmc0:b368 SD 1981440KiB > mmcblk0: p1 p2 p3 > s3c2410-rtc s3c2410-rtc: hctosys: invalid date/time > Waiting 3sec before mounting root device... > kjournald starting. Commit interval 5 seconds > EXT3 FS on mmcblk0p3, internal journal > EXT3-fs: mounted filesystem with ordered data mode. > VFS: Mounted root (ext3 filesystem). > Freeing init memory: 116K > Warning: unable to open an initial console. > ts_control_open! > ts_control_release! > Kernel panic - not syncing: Attempted to kill init! > Regards > Ranganath.S > > -- > unsubscribe: android-porting+unsubscr...@googlegroups.com > website: http://groups.google.com/group/android-porting > -- unsubscribe: android-porting+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-porting
