hi all
i am facing the problem with 2.6.32 omap kernel by providing all support
of android. i also disable the yaffs2 and provide rootdelay more than one ,
the kernel logs as follows.
CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7),
cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction
cache
Machine: OMAP3 Beagle
Board
Memory policy: ECC disabled, Data cache
writeback
OMAP3430/3530 ES3.0 (l2cache iva sgx neon isp
)
SRAM: Mapped pa 0x40200000 to va 0xfe400000 size:
0x100000
Reserving 4194304 bytes SDRAM for
VRAM
Built 1 zonelists in Zone order, mobility grouping on. Total pages:
65024
Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/mmcblk0p2
video=o
mapfb.mode=dvi:1280x720mr...@50 init=/init rootfstype=ext3 rw rootdelay=1
nohz=o
ff
androidboot.console=ttyS2
PID hash table entries: 1024 (order: 0, 4096
bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072
bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536
bytes)
Memory: 128MB 128MB = 256MB
total
Memory: 251136KB available (3812K code, 341K data, 140K init, 0K
highmem)
Hierarchical RCU
implementation.
NR_IRQS:402
Clocking rate (Crystal/Core/MPU): 26.0/332/500
MHz
Reprogramming SDRC clock to 332000000
Hz
GPMC revision
5.0
IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96
interrupts
Total of 96 interrupts on 1 active
controller
OMAP GPIO hardware version
2.5
OMAP clockevent source: GPTIMER12 at 32768
Hz
Console: colour dummy device
80x30
Calibrating delay loop... 478.91 BogoMIPS
(lpj=1867776)
Mount-cache hash table entries:
512
CPU: Testing write buffer coherency:
ok
regulator: core version
0.5
NET: Registered protocol family
16
MUX: setup J25_34XX_GPIO170 (0xfa0021c6): 0x001c ->
0x0104
MUX: setup Y9_3430_USB1HS_PHY_STP (0xfa0025d8): 0x001b ->
0x0003
MUX: setup Y8_3430_USB1HS_PHY_CLK (0xfa0025da): 0x0013 ->
0x0003
MUX: setup AA14_3430_USB1HS_PHY_DIR (0xfa0025ec): 0x0113 ->
0x010b
MUX: setup AA11_3430_USB1HS_PHY_NXT (0xfa0025ee): 0x0113 ->
0x010b
MUX: setup W13_3430_USB1HS_PHY_D0 (0xfa0025dc): 0x0113 ->
0x010b
MUX: setup W12_3430_USB1HS_PHY_D1 (0xfa0025de): 0x0113 ->
0x010b
MUX: setup W11_3430_USB1HS_PHY_D2 (0xfa0025e0): 0x0113 ->
0x010b
MUX: setup Y11_3430_USB1HS_PHY_D3 (0xfa0025ea): 0x0113 ->
0x010b
MUX: setup W9_3430_USB1HS_PHY_D4 (0xfa0025e4): 0x0113 ->
0x010b
MUX: setup Y12_3430_USB1HS_PHY_D5 (0xfa0025e6): 0x0113 ->
0x010b
MUX: setup W8_3430_USB1HS_PHY_D6 (0xfa0025e8): 0x0113 ->
0x010b
MUX: setup Y13_3430_USB1HS_PHY_D7 (0xfa0025e2): 0x0113 ->
0x010b
MUX: setup AA10_3430_USB2HS_PHY_STP (0xfa0025f2): 0x0013 ->
0x0003
MUX: setup AA8_3430_USB2HS_PHY_CLK (0xfa0025f0): 0x0013 ->
0x0003
MUX: setup AA9_3430_USB2HS_PHY_DIR (0xfa0025f4): 0x0113 ->
0x010b
MUX: setup AB11_3430_USB2HS_PHY_NXT (0xfa0025f6): 0x0113 ->
0x010b
MUX: setup AB10_3430_USB2HS_PHY_D0 (0xfa0025f8): 0x0113 ->
0x010b
MUX: setup AB9_3430_USB2HS_PHY_D1 (0xfa0025fa): 0x0113 ->
0x010b
MUX: setup W3_3430_USB2HS_PHY_D2 (0xfa0021d4): 0x0113 ->
0x010b
MUX: setup T4_3430_USB2HS_PHY_D3 (0xfa0021de): 0x0113 ->
0x010b
MUX: setup T3_3430_USB2HS_PHY_D4 (0xfa0021d8): 0x0113 ->
0x010b
MUX: setup R3_3430_USB2HS_PHY_D5 (0xfa0021da): 0x0113 ->
0x010b
MUX: setup R4_3430_USB2HS_PHY_D6 (0xfa0021dc): 0x0113 ->
0x010b
MUX: setup T2_3430_USB2HS_PHY_D7 (0xfa0021d6): 0x0113 ->
0x010b
Found NAND on
CS0
Registering NAND on
CS0
MUX: setup H16_34XX_SDRC_CKE0 (0xfa002262): 0x0118 ->
0x0000
MUX: setup H17_34XX_SDRC_CKE1 (0xfa002264): 0x0118 ->
0x0000
OMAP DMA hardware revision
4.0
bio: create slab <bio-0> at
0
SCSI subsystem
initialized
usbcore: registered new interface driver
usbfs
usbcore: registered new interface driver
hub
usbcore: registered new device driver
usb
i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600
kHz
twl4030: PIH (irq 7) chaining IRQs
368..375
twl4030: power (irq 373) chaining IRQs
376..383
twl4030: gpio (irq 368) chaining IRQs
384..401
MUX: setup AG9_34XX_GPIO23 (0xfa0025ee): 0x010b ->
0x0104
MUX: setup N28_3430_MMC1_CLK (0xfa002144): 0x0018 ->
0x0118
regulator: VUSB1V5: 1500 mV normal
standby
regulator: VUSB1V8: 1800 mV normal
standby
regulator: VUSB3V1: 3100 mV normal
standby
twl4030_usb twl4030_usb: Initialized TWL4030 USB
module
regulator: VMMC1: 1850 <--> 3150 mV normal
standby
regulator: VDAC: 1800 mV normal
standby
regulator: VPLL2: 1800 mV normal
standby
regulator: VSIM: 1800 <--> 3000 mV normal
standby
i2c_omap i2c_omap.3: bus 3 rev3.12 at 100
kHz
Switching to clocksource
32k_counter
musb_hdrc: version 6.0, musb-dma, otg (peripheral+host),
debug=0
musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ
92
NET: Registered protocol family
2
IP route cache hash table entries: 2048 (order: 1, 8192
bytes)
TCP established hash table entries: 8192 (order: 4, 65536
bytes)
TCP bind hash table entries: 8192 (order: 3, 32768
bytes)
TCP: Hash tables configured (established 8192 bind
8192)
TCP reno
registered
NET: Registered protocol family
1
RPC: Registered udp transport
module.
RPC: Registered tcp transport
module.
RPC: Registered tcp NFSv4.1 backchannel transport
module.
NetWinder Floating Point Emulator V0.97 (double
precision)
VFS: Disk quotas
dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
msgmni has been set to
490
alg: No test for stdrng
(krng)
io scheduler noop
registered
io scheduler anticipatory
registered
io scheduler deadline
registered
io scheduler cfq registered
(default)
Serial: 8250/16550 driver, 4 ports, IRQ sharing
enabled
serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a
ST16654
serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a
ST16654
serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a
ST16654
console [ttyS2]
enabled
brd: module
loaded
loop: module
loaded
usbcore: registered new interface driver
asix
usbcore: registered new interface driver
cdc_ether
usbcore: registered new interface driver
cdc_eem
usbcore: registered new interface driver
dm9601
usbcore: registered new interface driver
smsc95xx
usbcore: registered new interface driver
gl620a
usbcore: registered new interface driver
net1080
usbcore: registered new interface driver
plusb
usbcore: registered new interface driver
rndis_host
usbcore: registered new interface driver
cdc_subset
usbcore: registered new interface driver
zaurus
usbcore: registered new interface driver MOSCHIP usb-ethernet
driver
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
ehci-omap ehci-omap.0: OMAP-EHCI Host
Controller
ehci-omap ehci-omap.0: new USB bus registered, assigned bus number
1
ehci-omap ehci-omap.0: irq 77, io mem
0x48064800
ehci-omap ehci-omap.0: USB 2.0 started, EHCI
1.00
usb usb1: configuration #1 chosen from 1
choice
hub 1-0:1.0: USB hub
found
hub 1-0:1.0: 3 ports
detected
Initializing USB Mass Storage
driver...
usbcore: registered new interface driver
usb-storage
USB Mass Storage support
registered.
mice: PS/2 mouse device common for all
mice
input: gpio-keys as
/devices/platform/gpio-keys/input/input0
i2c /dev entries
driver
Linux video capture interface:
v2.00
OMAP Watchdog Timer Rev 0x31: initial timeout 60
sec
usbcore: registered new interface driver
usbhid
usbhid: v2.6:USB HID core
driver
Advanced Linux Sound Architecture Driver Version
1.0.21.
usbcore: registered new interface driver
snd-usb-audio
No device for DAI
twl4030
No device for DAI twl4030
Voice
No device for DAI
omap-mcbsp-dai-0
No device for DAI
omap-mcbsp-dai-1
No device for DAI
omap-mcbsp-dai-2
No device for DAI
omap-mcbsp-dai-3
No device for DAI
omap-mcbsp-dai-4
OMAP3 Beagle SoC
init
TWL4030 Audio Codec
init
asoc: twl4030 <-> omap-mcbsp-dai-0 mapping
ok
ALSA device
list:
#0: omap3beagle
(twl4030)
TCP cubic
registered
NET: Registered protocol family
17
NET: Registered protocol family
15
Power Management for TI
OMAP3.
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev
1
omapfb omapfb: no
displays
omapfb omapfb: failed to setup
omapfb
omapfb: probe of omapfb failed with error
-22
regulator_init_complete: incomplete constraints, leaving VDVI
on
regulator_init_complete: incomplete constraints, leaving VDAC
on
drivers/rtc/hctosys.c: unable to open rtc device
(rtc0)
Waiting 1sec before mounting root
device...
mmc0: new high speed SD card at address
aaaa
mmcblk0: mmc0:aaaa SD02G 1.84
GiB
mmcblk0: p1
p2
kjournald starting. Commit interval 5
seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is
recommended
EXT3 FS on mmcblk0p2, internal
journal
EXT3-fs: recovery
complete.
EXT3-fs: mounted filesystem with writeback data
mode.
VFS: Mounted root (ext3 filesystem) on device
179:2.
Freeing init memory:
140K
Warning: unable to open an initial
console.
Kernel panic - not syncing: Attempted to kill init!
any one has any solution for it plz help me .
thanks
joy
--
unsubscribe: android-porting+unsubscr...@googlegroups.com
website: http://groups.google.com/group/android-porting
