Hi, Do you have ashmem in your kernel?
Michael Grunditz Den 2010 9 3 14:56 skrev "jayasantosh samal" <joyn...@gmail.com>: > hi all > > i am facing the problem with 2.6.32 omap kernel by providing all support > of android. i also disable the yaffs2 and provide rootdelay more than one , > the kernel logs as follows. > > > CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), > cr=10c53c7f > CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction > cache > Machine: OMAP3 Beagle > Board > Memory policy: ECC disabled, Data cache > writeback > OMAP3430/3530 ES3.0 (l2cache iva sgx neon isp > ) > SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: > 0x100000 > Reserving 4194304 bytes SDRAM for > VRAM > Built 1 zonelists in Zone order, mobility grouping on. Total pages: > 65024 > Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/mmcblk0p2 > video=o > mapfb.mode=dvi:1280x720mr...@50 init=/init rootfstype=ext3 rw rootdelay=1 > nohz=o > ff > androidboot.console=ttyS2 > > PID hash table entries: 1024 (order: 0, 4096 > bytes) > Dentry cache hash table entries: 32768 (order: 5, 131072 > bytes) > Inode-cache hash table entries: 16384 (order: 4, 65536 > bytes) > Memory: 128MB 128MB = 256MB > total > Memory: 251136KB available (3812K code, 341K data, 140K init, 0K > highmem) > Hierarchical RCU > implementation. > NR_IRQS:402 > > Clocking rate (Crystal/Core/MPU): 26.0/332/500 > MHz > Reprogramming SDRC clock to 332000000 > Hz > GPMC revision > 5.0 > IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 > interrupts > Total of 96 interrupts on 1 active > controller > OMAP GPIO hardware version > 2.5 > OMAP clockevent source: GPTIMER12 at 32768 > Hz > Console: colour dummy device > 80x30 > Calibrating delay loop... 478.91 BogoMIPS > (lpj=1867776) > Mount-cache hash table entries: > 512 > CPU: Testing write buffer coherency: > ok > regulator: core version > 0.5 > NET: Registered protocol family > 16 > MUX: setup J25_34XX_GPIO170 (0xfa0021c6): 0x001c -> > 0x0104 > MUX: setup Y9_3430_USB1HS_PHY_STP (0xfa0025d8): 0x001b -> > 0x0003 > MUX: setup Y8_3430_USB1HS_PHY_CLK (0xfa0025da): 0x0013 -> > 0x0003 > MUX: setup AA14_3430_USB1HS_PHY_DIR (0xfa0025ec): 0x0113 -> > 0x010b > MUX: setup AA11_3430_USB1HS_PHY_NXT (0xfa0025ee): 0x0113 -> > 0x010b > MUX: setup W13_3430_USB1HS_PHY_D0 (0xfa0025dc): 0x0113 -> > 0x010b > MUX: setup W12_3430_USB1HS_PHY_D1 (0xfa0025de): 0x0113 -> > 0x010b > MUX: setup W11_3430_USB1HS_PHY_D2 (0xfa0025e0): 0x0113 -> > 0x010b > MUX: setup Y11_3430_USB1HS_PHY_D3 (0xfa0025ea): 0x0113 -> > 0x010b > MUX: setup W9_3430_USB1HS_PHY_D4 (0xfa0025e4): 0x0113 -> > 0x010b > MUX: setup Y12_3430_USB1HS_PHY_D5 (0xfa0025e6): 0x0113 -> > 0x010b > MUX: setup W8_3430_USB1HS_PHY_D6 (0xfa0025e8): 0x0113 -> > 0x010b > MUX: setup Y13_3430_USB1HS_PHY_D7 (0xfa0025e2): 0x0113 -> > 0x010b > MUX: setup AA10_3430_USB2HS_PHY_STP (0xfa0025f2): 0x0013 -> > 0x0003 > MUX: setup AA8_3430_USB2HS_PHY_CLK (0xfa0025f0): 0x0013 -> > 0x0003 > MUX: setup AA9_3430_USB2HS_PHY_DIR (0xfa0025f4): 0x0113 -> > 0x010b > MUX: setup AB11_3430_USB2HS_PHY_NXT (0xfa0025f6): 0x0113 -> > 0x010b > MUX: setup AB10_3430_USB2HS_PHY_D0 (0xfa0025f8): 0x0113 -> > 0x010b > MUX: setup AB9_3430_USB2HS_PHY_D1 (0xfa0025fa): 0x0113 -> > 0x010b > MUX: setup W3_3430_USB2HS_PHY_D2 (0xfa0021d4): 0x0113 -> > 0x010b > MUX: setup T4_3430_USB2HS_PHY_D3 (0xfa0021de): 0x0113 -> > 0x010b > MUX: setup T3_3430_USB2HS_PHY_D4 (0xfa0021d8): 0x0113 -> > 0x010b > MUX: setup R3_3430_USB2HS_PHY_D5 (0xfa0021da): 0x0113 -> > 0x010b > MUX: setup R4_3430_USB2HS_PHY_D6 (0xfa0021dc): 0x0113 -> > 0x010b > MUX: setup T2_3430_USB2HS_PHY_D7 (0xfa0021d6): 0x0113 -> > 0x010b > Found NAND on > CS0 > Registering NAND on > CS0 > MUX: setup H16_34XX_SDRC_CKE0 (0xfa002262): 0x0118 -> > 0x0000 > MUX: setup H17_34XX_SDRC_CKE1 (0xfa002264): 0x0118 -> > 0x0000 > OMAP DMA hardware revision > 4.0 > bio: create slab <bio-0> at > 0 > SCSI subsystem > initialized > usbcore: registered new interface driver > usbfs > usbcore: registered new interface driver > hub > usbcore: registered new device driver > usb > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 > kHz > twl4030: PIH (irq 7) chaining IRQs > 368..375 > twl4030: power (irq 373) chaining IRQs > 376..383 > twl4030: gpio (irq 368) chaining IRQs > 384..401 > MUX: setup AG9_34XX_GPIO23 (0xfa0025ee): 0x010b -> > 0x0104 > MUX: setup N28_3430_MMC1_CLK (0xfa002144): 0x0018 -> > 0x0118 > regulator: VUSB1V5: 1500 mV normal > standby > regulator: VUSB1V8: 1800 mV normal > standby > regulator: VUSB3V1: 3100 mV normal > standby > twl4030_usb twl4030_usb: Initialized TWL4030 USB > module > regulator: VMMC1: 1850 <--> 3150 mV normal > standby > regulator: VDAC: 1800 mV normal > standby > regulator: VPLL2: 1800 mV normal > standby > regulator: VSIM: 1800 <--> 3000 mV normal > standby > i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 > kHz > Switching to clocksource > 32k_counter > musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), > debug=0 > musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ > 92 > NET: Registered protocol family > 2 > IP route cache hash table entries: 2048 (order: 1, 8192 > bytes) > TCP established hash table entries: 8192 (order: 4, 65536 > bytes) > TCP bind hash table entries: 8192 (order: 3, 32768 > bytes) > TCP: Hash tables configured (established 8192 bind > 8192) > TCP reno > registered > NET: Registered protocol family > 1 > RPC: Registered udp transport > module. > RPC: Registered tcp transport > module. > RPC: Registered tcp NFSv4.1 backchannel transport > module. > NetWinder Floating Point Emulator V0.97 (double > precision) > VFS: Disk quotas > dquot_6.5.2 > Dquot-cache hash table entries: 1024 (order 0, 4096 > bytes) > msgmni has been set to > 490 > alg: No test for stdrng > (krng) > io scheduler noop > registered > io scheduler anticipatory > registered > io scheduler deadline > registered > io scheduler cfq registered > (default) > Serial: 8250/16550 driver, 4 ports, IRQ sharing > enabled > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a > ST16654 > serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a > ST16654 > serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a > ST16654 > console [ttyS2] > enabled > brd: module > loaded > loop: module > loaded > usbcore: registered new interface driver > asix > usbcore: registered new interface driver > cdc_ether > usbcore: registered new interface driver > cdc_eem > usbcore: registered new interface driver > dm9601 > usbcore: registered new interface driver > smsc95xx > usbcore: registered new interface driver > gl620a > usbcore: registered new interface driver > net1080 > usbcore: registered new interface driver > plusb > usbcore: registered new interface driver > rndis_host > usbcore: registered new interface driver > cdc_subset > usbcore: registered new interface driver > zaurus > usbcore: registered new interface driver MOSCHIP usb-ethernet > driver > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) > Driver > ehci-omap ehci-omap.0: OMAP-EHCI Host > Controller > ehci-omap ehci-omap.0: new USB bus registered, assigned bus number > 1 > ehci-omap ehci-omap.0: irq 77, io mem > 0x48064800 > ehci-omap ehci-omap.0: USB 2.0 started, EHCI > 1.00 > usb usb1: configuration #1 chosen from 1 > choice > hub 1-0:1.0: USB hub > found > hub 1-0:1.0: 3 ports > detected > Initializing USB Mass Storage > driver... > usbcore: registered new interface driver > usb-storage > USB Mass Storage support > registered. > mice: PS/2 mouse device common for all > mice > input: gpio-keys as > /devices/platform/gpio-keys/input/input0 > i2c /dev entries > driver > Linux video capture interface: > v2.00 > OMAP Watchdog Timer Rev 0x31: initial timeout 60 > sec > usbcore: registered new interface driver > usbhid > usbhid: v2.6:USB HID core > driver > Advanced Linux Sound Architecture Driver Version > 1.0.21. > usbcore: registered new interface driver > snd-usb-audio > No device for DAI > twl4030 > No device for DAI twl4030 > Voice > No device for DAI > omap-mcbsp-dai-0 > No device for DAI > omap-mcbsp-dai-1 > No device for DAI > omap-mcbsp-dai-2 > No device for DAI > omap-mcbsp-dai-3 > No device for DAI > omap-mcbsp-dai-4 > OMAP3 Beagle SoC > init > TWL4030 Audio Codec > init > asoc: twl4030 <-> omap-mcbsp-dai-0 mapping > ok > ALSA device > list: > #0: omap3beagle > (twl4030) > TCP cubic > registered > NET: Registered protocol family > 17 > NET: Registered protocol family > 15 > Power Management for TI > OMAP3. > VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev > 1 > omapfb omapfb: no > displays > omapfb omapfb: failed to setup > omapfb > omapfb: probe of omapfb failed with error > -22 > regulator_init_complete: incomplete constraints, leaving VDVI > on > regulator_init_complete: incomplete constraints, leaving VDAC > on > drivers/rtc/hctosys.c: unable to open rtc device > (rtc0) > Waiting 1sec before mounting root > device... > mmc0: new high speed SD card at address > aaaa > mmcblk0: mmc0:aaaa SD02G 1.84 > GiB > mmcblk0: p1 > p2 > kjournald starting. Commit interval 5 > seconds > EXT3-fs warning: maximal mount count reached, running e2fsck is > recommended > EXT3 FS on mmcblk0p2, internal > journal > EXT3-fs: recovery > complete. > EXT3-fs: mounted filesystem with writeback data > mode. > VFS: Mounted root (ext3 filesystem) on device > 179:2. > Freeing init memory: > 140K > Warning: unable to open an initial > console. > Kernel panic - not syncing: Attempted to kill init! > > any one has any solution for it plz help me . > > thanks > joy > > -- > unsubscribe: > android-porting+unsubscr...@googlegroups.com<android-porting%2bunsubscr...@googlegroups.com> > website: http://groups.google.com/group/android-porting -- unsubscribe: android-porting+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-porting
