Hi, Which android package are you booting with beagleboard?? You can make sure your setup is good with prebuilt binaries from rowboat/0xdroid.,
-- Regards, Deva www.bittoggler.com On Tue, Sep 7, 2010 at 11:40 AM, jayasantosh samal <joyn...@gmail.com>wrote: > > > > > > hi all > > i am facing kernel panic form last 7days ,i am trying to add the > android support in omap 2.6.32 kernel, i have also enable the kernel trace > can any body have facing this type of problem privously, plz help me. > > CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), > cr=10c53c7f > CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction > cache > Machine: OMAP3 Beagle > Board > Memory policy: ECC disabled, Data cache > writeback > OMAP3430/3530 ES3.0 (l2cache iva sgx neon isp > ) > SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: > 0x100000 > Built 1 zonelists in Zone order, mobility grouping on. Total pages: > 64960 > Kernel command line: console=ttyS2,115200n8 noinitrd root=/dev/mmcblk0p2 > video=o > mapfb.mode=dvi:1280x720mr...@50 init=/init rootfstype=ext3 rw rootdelay=1 > nohz=o > ff > androidboot.console=ttyS2 > > PID hash table entries: 1024 (order: 0, 4096 > bytes) > Dentry cache hash table entries: 32768 (order: 5, 131072 > bytes) > Inode-cache hash table entries: 16384 (order: 4, 65536 > bytes) > Memory: 128MB 128MB = 256MB > total > Memory: 254336KB available (3988K code, 756K data, 128K init, 0K > highmem) > Hierarchical RCU > implementation. > NR_IRQS:402 > > Clocking rate (Crystal/Core/MPU): 26.0/332/500 > MHz > Reprogramming SDRC clock to 332000000 > Hz > GPMC revision > 5.0 > IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 > interrupts > Total of 96 interrupts on 1 active > controller > OMAP GPIO hardware version > 2.5 > OMAP clockevent source: GPTIMER12 at 32768 > Hz > Console: colour dummy device > 80x30 > Calibrating delay loop... 476.81 BogoMIPS > (lpj=1859584) > Mount-cache hash table entries: > 512 > CPU: Testing write buffer coherency: > ok > regulator: core version > 0.5 > NET: Registered protocol family > 16 > Found NAND on > CS0 > Registering NAND on > CS0 > OMAP DMA hardware revision > 4.0 > bio: create slab <bio-0> at > 0 > SCSI subsystem > initialized > usbcore: registered new interface driver > usbfs > usbcore: registered new interface driver > hub > usbcore: registered new device driver > usb > i2c_omap i2c_omap.1: bus 1 rev3.12 at 2600 > kHz > twl4030: PIH (irq 7) chaining IRQs > 368..375 > twl4030: power (irq 373) chaining IRQs > 376..383 > twl4030: gpio (irq 368) chaining IRQs > 384..401 > regulator: VUSB1V5: 1500 mV normal > standby > regulator: VUSB1V8: 1800 mV normal > standby > regulator: VUSB3V1: 3100 mV normal > standby > twl4030_usb twl4030_usb: Initialized TWL4030 USB > module > regulator: VMMC1: 1850 <--> 3150 mV normal > standby > regulator: VDAC: 1800 mV normal > standby > regulator: VPLL2: 1800 mV normal > standby > regulator: VSIM: 1800 <--> 3000 mV normal > standby > i2c_omap i2c_omap.3: bus 3 rev3.12 at 100 > kHz > Switching to clocksource > 32k_counter > musb_hdrc: version 6.0, musb-dma, otg (peripheral+host), > debug=0 > musb_hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ > 92 > NET: Registered protocol family > 2 > IP route cache hash table entries: 2048 (order: 1, 8192 > bytes) > TCP established hash table entries: 8192 (order: 4, 65536 > bytes) > TCP bind hash table entries: 8192 (order: 3, 32768 > bytes) > TCP: Hash tables configured (established 8192 bind > 8192) > TCP reno > registered > NET: Registered protocol family > 1 > RPC: Registered udp transport > module. > RPC: Registered tcp transport > module. > RPC: Registered tcp NFSv4.1 backchannel transport > module. > NetWinder Floating Point Emulator V0.97 (double > precision) > ====[ backtrace testing > ]=========== > Testing a backtrace from process > context. > The following trace is a kernel self test and not a > bug! > [<c002e678>] (unwind_backtrace+0x0/0xe0) from [<c0075b6c>] > (backtrace_regression > _test+0x28/0xb0) > > [<c0075b6c>] (backtrace_regression_test+0x28/0xb0) from [<c002833c>] > (do_one_ini > tcall+0x54/0x190) > > [<c002833c>] (do_one_initcall+0x54/0x190) from [<c000885c>] > (kernel_init+0x90/0x > 108) > > [<c000885c>] (kernel_init+0x90/0x108) from [<c0029e50>] > (kernel_thread_exit+0x0/ > 0x8) > > Testing a backtrace from irq > context. > The following trace is a kernel self test and not a > bug! > [<c002e678>] (unwind_backtrace+0x0/0xe0) from [<c0075b34>] > (backtrace_test_irq_c > allback+0x8/0x18) > > [<c0075b34>] (backtrace_test_irq_callback+0x8/0x18) from [<c0055d90>] > (tasklet_a > ction+0x68/0xb8) > > [<c0055d90>] (tasklet_action+0x68/0xb8) from [<c0055ba0>] > (__do_softirq+0x70/0xf > 4) > > [<c0055ba0>] (__do_softirq+0x70/0xf4) from [<c0055c64>] > (do_softirq+0x40/0x4c) > [<c0055c64>] (do_softirq+0x40/0x4c) from [<c0055ebc>] > (ksoftirqd+0x50/0xe4) > [<c0055ebc>] (ksoftirqd+0x50/0xe4) from [<c0062e54>] > (kthread+0x7c/0x84) > [<c0062e54>] (kthread+0x7c/0x84) from [<c0029e50>] > (kernel_thread_exit+0x0/0x8) > Saved backtrace test > skipped. > ====[ end of backtrace testing > ]==== > ashmem: > initialized > VFS: Disk quotas > dquot_6.5.2 > Dquot-cache hash table entries: 1024 (order 0, 4096 > bytes) > JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, > Inc. > msgmni has been set to > 497 > alg: No test for stdrng > (krng) > io scheduler noop > registered > io scheduler anticipatory registered > (default) > io scheduler deadline > registered > io scheduler cfq > registered > Serial: 8250/16550 driver, 4 ports, IRQ sharing > enabled > serial8250.0: ttyS0 at MMIO 0x4806a000 (irq = 72) is a > ST16654 > serial8250.1: ttyS1 at MMIO 0x4806c000 (irq = 73) is a > ST16654 > serial8250.2: ttyS2 at MMIO 0x49020000 (irq = 74) is a > ST16654 > console [ttyS2] > enabled > brd: module > loaded > loop: module > loaded > omap2-nand driver > initializing > NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 256MiB 1,8V > 16-bi > t) > > cmdlinepart partition parsing not > available > Creating 5 MTD partitions on > "omap2-nand": > 0x000000000000-0x000000080000 : > "X-Loader" > 0x000000080000-0x000000260000 : > "U-Boot" > 0x000000260000-0x000000280000 : "U-Boot > Env" > 0x000000280000-0x000000680000 : > "Kernel" > 0x000000680000-0x000010000000 : "File > System" > ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) > Driver > ehci-omap ehci-omap.0: OMAP-EHCI Host > Controller > ehci-omap ehci-omap.0: new USB bus registered, assigned bus number > 1 > ehci-omap ehci-omap.0: irq 77, io mem > 0x48064800 > ehci-omap ehci-omap.0: USB 2.0 started, EHCI > 1.00 > usb usb1: New USB device found, idVendor=1d6b, > idProduct=0002 > usb usb1: New USB device strings: Mfr=3, Product=2, > SerialNumber=1 > usb usb1: Product: OMAP-EHCI Host > Controller > usb usb1: Manufacturer: Linux 2.6.32-06909-g2a20002-dirty > ehci_hcd > usb usb1: SerialNumber: > ehci-omap.0 > usb usb1: configuration #1 chosen from 1 > choice > hub 1-0:1.0: USB hub > found > hub 1-0:1.0: 3 ports > detected > Initializing USB Mass Storage > driver... > usbcore: registered new interface driver > usb-storage > USB Mass Storage support > registered. > twl4030_rtc twl4030_rtc: rtc core: registered twl4030_rtc as > rtc0 > twl4030_rtc twl4030_rtc: Power up reset > detected. > twl4030_rtc twl4030_rtc: Enabling > TWL4030-RTC. > i2c /dev entries > driver > usbcore: registered new interface driver > usbhid > usbhid: v2.6:USB HID core > driver > logger: created 64K log > 'log_main' > logger: created 256K log > 'log_events' > logger: created 64K log > 'log_radio' > Advanced Linux Sound Architecture Driver Version > 1.0.21. > No device for DAI > AD73311 > No device for DAI > AK4535 > Cirrus Logic CS4270 ALSA SoC Codec > Driver > No device for DAI PCM3008 > HiFi > No device for DAI > SSM2602 > No device for DAI > tlv320aic23 > No device for DAI > twl4030 > No device for DAI twl4030 > Voice > No device for DAI > UDA134X > No device for DAI WM8510 > HiFi > No device for DAI > WM8728 > No device for DAI > WM8750 > No device for DAI > WM8971 > No device for DAI WM8990 ADC/DAC > Primary > No device for DAI > omap-mcbsp-dai-0 > No device for DAI > omap-mcbsp-dai-1 > No device for DAI > omap-mcbsp-dai-2 > No device for DAI > omap-mcbsp-dai-3 > No device for DAI > omap-mcbsp-dai-4 > OMAP3 Beagle SoC > init > TWL4030 Audio Codec > init > asoc: twl4030 <-> omap-mcbsp-dai-0 mapping > ok > ALSA device > list: > #0: omap3beagle > (twl4030) > TCP cubic > registered > NET: Registered protocol family > 17 > NET: Registered protocol family > 15 > Power Management for TI > OMAP3. > VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev > 1 > omapfb omapfb: no > displays > omapfb omapfb: failed to setup > omapfb > omapfb: probe of omapfb failed with error > -22 > regulator_init_complete: incomplete constraints, leaving VDVI > on > regulator_init_complete: incomplete constraints, leaving VDAC > on > twl4030_rtc twl4030_rtc: setting system clock to 2000-01-01 00:00:00 UTC > (946684 > 800) > > Waiting 1sec before mounting root > device... > mmc0: new high speed SD card at address > aaaa > mmcblk0: mmc0:aaaa SD02G 1.84 > GiB > mmcblk0: p1 > p2 > kjournald starting. Commit interval 5 > seconds > EXT3-fs warning: maximal mount count reached, running e2fsck is > recommended > EXT3 FS on mmcblk0p2, internal > journal > EXT3-fs: mounted filesystem with writeback data > mode. > VFS: Mounted root (ext3 filesystem) on device > 179:2. > Freeing init memory: > 128K > Warning: unable to open an initial > console. > Kernel panic - not syncing: Attempted to kill > init! > [<c002e678>] (unwind_backtrace+0x0/0xe0) from [<c00512bc>] > (panic+0x40/0x110) > [<c00512bc>] (panic+0x40/0x110) from [<c0053c88>] > (do_exit+0x5c/0x57c) > [<c0053c88>] (do_exit+0x5c/0x57c) from [<c0054224>] > (do_group_exit+0x7c/0xac) > [<c0054224>] (do_group_exit+0x7c/0xac) from [<c005cca8>] > (get_signal_to_deliver+ > 0x2bc/0x2ec) > > [<c005cca8>] (get_signal_to_deliver+0x2bc/0x2ec) from [<c002b58c>] > (do_notify_re > sume+0x5c/0x580) > > [<c002b58c>] (do_notify_resume+0x5c/0x580) from [<c0028ecc>] > (work_pending+0x1c/ > 0x20) > > > advance thank > jaya > > > -- > unsubscribe: > android-porting+unsubscr...@googlegroups.com<android-porting%2bunsubscr...@googlegroups.com> > website: http://groups.google.com/group/android-porting > -- unsubscribe: android-porting+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-porting