Thanks.Yes, you were right. I tried replacing with O with S. Now I can see logs in the console.
Can you tell me where in the source code it says use ttyO instead of ttyS? I couldn't find in the source. Manish On Fri, Jul 15, 2011 at 11:53 AM, Manish Shakya <manishshakya...@gmail.com>wrote: > > What do you mean? > > so now uboot args should look something like this > console=ttyS2,115200n8 androidboot.console=ttyO2 root=/dev/mmcblk0p2 rw > rootfstype=ext3 rootwait init=/init vram=12M omapfb.mode=dvi:480x272MR-16@ > 60 omapdss.def_disp=lcd43 > > Is this change in gingerbread 2.3.4 only? > > Manish > > > On Fri, Jul 15, 2011 at 11:48 AM, hedwin <hedwin.kon...@gmail.com> wrote: > >> in gingerbread ttyS changed to ttyO >> >> Hedwin >> >> >> On Fri, Jul 15, 2011 at 5:44 PM, Manish Shakya <manishshakya...@gmail.com >> > wrote: >> >>> Right now I am trying to move from linux kernel 2.6.32 to 2.6.37 and use >>> gingerbread 2.3.4. >>> >>> With linux kernel 2.6.32, froyo and gb 2.3.3 are working fine. I used >>> same uboot arg as in earlier mail. >>> >>> On Fri, Jul 15, 2011 at 11:22 AM, hedwin <hedwin.kon...@gmail.com>wrote: >>> >>>> Do you use froyo or gingerbread? >>>> >>>> >>>> >>>> On Fri, Jul 15, 2011 at 3:57 PM, manish shakya <msha...@oakland.edu>wrote: >>>> >>>>> Yes, Both console and android.console is pointing to correct serial >>>>> device i.e. ttyS2. >>>>> >>>>> My uboot args is >>>>> >>>>> console=ttyS2,115200n8 androidboot.console=ttyS2 root=/dev/mmcblk0p2 rw >>>>> rootfstype=ext3 rootwait init=/init vram=12M >>>>> omapfb.mode=dvi:480x272MR-16@60omapdss.def_disp=lcd43 >>>>> >>>>> Isn't this correct? >>>>> >>>>> >>>>> On Fri, Jul 15, 2011 at 5:44 AM, hedwin <hedwin.kon...@gmail.com> >>>>> wrote: >>>>> > >>>>> > Check if console and android.console point to the correct serial >>>>> device. >>>>> > Both a kernel parameters sent by u-boot. >>>>> > >>>>> > Cheers, >>>>> > >>>>> > Hedwin >>>>> > >>>>> > On Thu, Jul 14, 2011 at 9:45 PM, Manish Shakya < >>>>> manishshakya...@gmail.com> wrote: >>>>> >> >>>>> >> Hi , >>>>> >> >>>>> >> I am wondering what are the changes to be made if I have to make to >>>>> port rowboat to gumstix overo module. >>>>> >> >>>>> >> I did following things but it didn't worked. :-( >>>>> >> I made change in config file , board-overo.c and also added LCD >>>>> driver. Compilation went fine with out errors. >>>>> >> But when I tried to run the image. It show following log and gets >>>>> stuck. >>>>> >> >>>>> >> 2731240 bytes read >>>>> >> ## Booting kernel from Legacy Image at 82000000 ... >>>>> >> Image Name: Linux-2.6.37-g06ebbba >>>>> >> Image Type: ARM Linux Kernel Image (uncompressed) >>>>> >> Data Size: 2731176 Bytes = 2.6 MiB >>>>> >> Load Address: 80008000 >>>>> >> Entry Point: 80008000 >>>>> >> Verifying Checksum ... OK >>>>> >> Loading Kernel Image ... OK >>>>> >> OK >>>>> >> >>>>> >> Starting kernel ... >>>>> >> >>>>> >> Uncompressing Linux... done, booting the kernel. >>>>> >> >>>>> >> >>>>> >> -- >>>>> >> Manish Shakya >>>>> >> http://www.manishshakya.com.np >>>>> >> >>>>> >> -- >>>>> >> unsubscribe: android-porting+unsubscr...@googlegroups.com >>>>> >> website: http://groups.google.com/group/android-porting >>>>> > >>>>> >>>>> >>>>> >>>>> -- >>>>> >>>>> Manish Shakya >>>>> http://www.manishshakya.com.np >>>>> http://secs.oakland.edu/~ganesan/iMX/ >>>>> >>>> >>>> >>> >>> >>> -- >>> Manish Shakya >>> http://www.manishshakya.com.np >>> http://secs.oakland.edu/~ganesan/iMX/ >>> >> >> > > > -- > Manish Shakya > http://www.manishshakya.com.np > http://secs.oakland.edu/~ganesan/iMX/ > -- Manish Shakya http://www.manishshakya.com.np http://secs.oakland.edu/~ganesan/iMX/ -- unsubscribe: android-porting+unsubscr...@googlegroups.com website: http://groups.google.com/group/android-porting