Hi, On 09/09/2014 01:59 PM, Robert Moskowitz wrote: > I am at ITS World Congress in downtown Detroit today, so I can't do any > testing until this evening... > > On 09/09/2014 07:02 AM, Hans de Goede wrote: >> Hi, >> >> On 09/09/2014 12:28 PM, Robert Moskowitz wrote: >>> On 09/09/2014 02:41 AM, Hans de Goede wrote: >>>> Hi, >>>> >>>> On 09/09/2014 07:40 AM, Marcin Juszkiewicz wrote: >>>>> W dniu 09.09.2014 o 04:51, Robert Moskowitz pisze: >>>>>> Read Hans de Goede's post on the F19 and the Allwinner (Cubie) back on >>>>>> 12/26/2013. He supposedly uses the SID for a consistant local scope >>>>>> MACaddr. I Do get that on my Cubieboard2, but not on my Cubietruck. >>>>> Hans also told that there was a bunch of Cubie* with pre-production cpus >>>>> which lacked serial number. >>>> AFAIK only cubieboard2 and olinuxino-a20-micro suffer from this, the >>>> cubietruck is fine. On machines with an all 0 sid this indeed does not >>>> work. >>> My SIX Cubieboard2 all are fine with a consistant MAC address. >> Good, then later runs of the cubieboard2 have gotten a proper SID, that is >> good. >> >>> My one Cubietruck keeps coming up with the unique MACaddr. Exact opposite >>> of what you are reporting. >> Which version of Fedora are you running on your Cubietruck ? > Your F19 and last the 9/5 build of F21-minimal. Here is what I do for the > F19: > > http://docs.cubieboard.org/tutorials/cb2/installation/cb2_fedora_19_card_install > xzcat /home/rgm/arm/Fedora-19-a10-armhfp-r3.img.xz > /dev/sdb; sync > <reinsert card> > /run/media/rgm/uboot/select-board.sh cubieboard2[cubietruck] > umount /run/media/rgm/uboot > umount /run/media/rgm/rootfs > > I never saw anything after the R3 release. > > >> >> With the respin images the kernel takes care of getting the MAC from the SID, >> with the official F-21 images, u-boot needs to do this, and the u-boot >> included >> is (not yet) new enough. > > hmmm. For cubieboard2, I use your git repo: > > git clone https://github.com/jwrdegoede/u-boot-sunxi.git > cd u-boot-sunxi > git checkout -B next origin/next > make -j4 CROSS_COMPILE=arm-linux-gnu- Cubieboard2_defconfig > make -j4 CROSS_COMPILE=arm-linux-gnu- > dd if=u-boot-sunxi-with-spl.bin of=/dev/sdb bs=1024 seek=8 > sync > > Is there a way to also make a uboot for the cubietruck to update what is on > koji?
Yes, replace Cubieboard2 with Cubietruck, and replace https://github.com/jwrdegoede/u-boot-sunxi.git with git://git.denx.de/u-boot.git >>> Perhaps there is a rev difference in the shipped nand? In all cases, I >>> never did anything with the nand image, but went right to the SDcard image. >>> I just don't get how to do the nand poking to get something working from >>> it. >> The SID is in the SoC, it has nothing to do with the nand. > > Well that is a start. > >> >>> Is there any test I can run on my CT? >> You can dump the sid by hooking up a serial console, and then pressing a >> key to interrupt u-boot, then do: >> >> md 1c23800 4 > > If I don't have an SDcard in the unit I end up at a sunxi# prompt. Is this > the same thing? Probably, if the md command works and the output resembles the one from: http://linux-sunxi.org/SID_Register_Guide > >> >> To get the SID contents, see here for example SID-s : >> >> http://linux-sunxi.org/SID_Register_Guide >> >> If this is non-0 on your cubietruck, then you should get a consistent MAC >> with the respin images, and you should be able to get a consistent MAC >> with F-21 by building (and installing) u-boot from here: >> >> http://git.denx.de/?p=u-boot.git;a=summary > > Makes no sense to me. What do I do with this? It gives you the clone url: git://git.denx.de/u-boot.git Regards, Hans _______________________________________________ arm mailing list arm@lists.fedoraproject.org https://admin.fedoraproject.org/mailman/listinfo/arm
