Hi,
i was unable to get any UART from uboot with the original firmware and with my
own built uboot. Geniatech confirmed they will fix it in a future. The fix was
released yesterday and now i can interact witrh uboot. They haven't clarified
what the issue was, but i suspect it was in the miniloader (bootrom), as my own
built uboot works now aswell.
So, i tried to boot OpenBSD on it:
I have downloaded the arm64 miniroot74.img and loop-mounted it on linux.
Mounted the EFI partition and inserted my own DTB file. Then i dumped both the
EFI and the OpenBSD partition into a separate image-file (dd if=/dev/loop0p1
of=./EFI.img and dd if=/dev/loop0p4 of=./BSD.img )
Then i manually created a parameter.txt file, which describes the partition
layout. I have created 4 partitions: UBOOT, EFI, ROOT, USERDATA and wrote it
into the MMC using rkdeveloptool.
Then i have flashed the images to the correct partition using rkdeveloptool, so
i have flashed u-boot to UBOOT, the EFI.img to the EFI partition, the BSD.img
to the ROOT partition and i have kept the USERDATA empty for now.
I have booted the board and it went straight to the U-Boot prompt, where i have
loaded the DTB and the EFI loader and started it. It jumped into the OpenBSD
bootloader just fine, but then i got stuck, as the bootloader doesn't want to
boot the ROOT partition, it complains the partition is bad. See the logs below.
I have also tried to boot the other partitions, but the result is the same. Can
you point out what am i doing wrong here?
Thank You very much and have a great day!
Best Regards,
-- Z --
--------------
BOOTLOG:
DDR V1.18 f366f69a7d typ 23/07/17-15:48:58
ln
LP4/4x derate en, other dram:1x trefi
ddrconfig:0
LP4 MR14:0x4d
LPDDR4, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
tdqss: cs0 dqs0: 48ps, dqs1: -72ps, dqs2: -48ps, dqs3: -96ps,
change to: 324MHz
clk skew:0x60
change to: 528MHz
clk skew:0x58
change to: 780MHz
clk skew:0x58
change to: 1056MHz(final freq)
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:29%
dram drv:40,odt:80
vref_ca:00000068
clk skew:0x35
cs 0:
the read training result:
DQS0:0x42, DQS1:0x40, DQS2:0x3e, DQS3:0x3c,
min : 0x9 0xd 0x10 0xd 0xd 0xd 0x9 0x1 , 0x3 0xb 0x1 0xd 0x11 0x10
0x12 0x10 ,
0xc 0xb 0xb 0x9 0x3 0x1 0x6 0x3 , 0x8 0x7 0x4 0x2 0xa 0xc
0x7 0x9 ,
mid :0x28 0x2b 0x2f 0x2c 0x2c 0x2a 0x28 0x20 ,0x22 0x2a 0x22 0x2d 0x30 0x30
0x30 0x2f ,
0x2a 0x2a 0x2a 0x28 0x21 0x20 0x24 0x23 ,0x26 0x26 0x23 0x21 0x28 0x2a
0x25 0x28 ,
max :0x47 0x4a 0x4e 0x4c 0x4b 0x47 0x47 0x40 ,0x41 0x49 0x43 0x4d 0x50 0x50
0x4f 0x4e ,
0x48 0x49 0x49 0x47 0x40 0x3f 0x42 0x43 ,0x45 0x45 0x43 0x40 0x47 0x48
0x44 0x47 ,
range:0x3e 0x3d 0x3e 0x3f 0x3e 0x3a 0x3e 0x3f ,0x3e 0x3e 0x42 0x40 0x3f 0x40
0x3d 0x3e ,
0x3c 0x3e 0x3e 0x3e 0x3d 0x3e 0x3c 0x40 ,0x3d 0x3e 0x3f 0x3e 0x3d 0x3c
0x3d 0x3e ,
the write training result:
DQS0:0x3b, DQS1:0x2c, DQS2:0x2f, DQS3:0x29,
min :0x51 0x56 0x58 0x57 0x56 0x54 0x53 0x4d 0x56 ,0x40 0x48 0x42 0x4d 0x4e
0x50 0x4f 0x,
0x4c 0x4c 0x4c 0x4d 0x47 0x46 0x48 0x49 0x48 ,0x42 0x44 0x3f 0x3d 0x47
0x48 0x43 0x,
mid :0x6f 0x73 0x76 0x74 0x73 0x71 0x70 0x6a 0x72 ,0x5d 0x66 0x5e 0x6a 0x6b
0x6d 0x6b 0x,
0x6a 0x6a 0x69 0x69 0x63 0x63 0x64 0x65 0x65 ,0x5e 0x60 0x5c 0x5a 0x64
0x65 0x5f 0x,
max :0x8e 0x91 0x94 0x91 0x90 0x8f 0x8d 0x87 0x8f ,0x7b 0x84 0x7b 0x87 0x88
0x8a 0x88 0x,
0x89 0x89 0x87 0x86 0x80 0x80 0x81 0x81 0x82 ,0x7b 0x7c 0x7a 0x78 0x81
0x83 0x7b 0x,
range:0x3d 0x3b 0x3c 0x3a 0x3a 0x3b 0x3a 0x3a 0x39 ,0x3b 0x3c 0x39 0x3a 0x3a
0x3a 0x39 0x,
0x3d 0x3d 0x3b 0x39 0x39 0x3a 0x39 0x38 0x3a ,0x39 0x38 0x3b 0x3b 0x3a
0x3b 0x38 0x,
CA Training result:
cs:0 min :0x47 0x42 0x41 0x38 0x3c 0x34 0x42 ,0x48 0x40 0x40 0x38 0x3d 0x34
0x42 ,
cs:0 mid :0x83 0x84 0x7d 0x7a 0x78 0x77 0x6f ,0x83 0x81 0x7c 0x79 0x79 0x75
0x6f ,
cs:0 max :0xc0 0xc6 0xb9 0xbc 0xb5 0xba 0x9d ,0xbf 0xc3 0xb8 0xbb 0xb6 0xb7
0x9d ,
cs:0 range:0x79 0x84 0x78 0x84 0x79 0x86 0x5b ,0x77 0x83 0x78 0x83 0x79 0x83
0x5b ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-gaaca6ffec1-211203 #zzz (Dec 03 2021 - 18:42:16)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 10
spl: mmc init failed with error: -95
Trying to boot from MMC1
No misc partition
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(2f01bd8955...) + OK
## Checking uboot 0x00a00000 ... sha256(1a594eea32...) + OK
## Checking fdt 0x00b237b8 ... sha256(d408797509...) + OK
## Checking atf-2 0xfdcc9000 ... sha256(f1fecab971...) + OK
## Checking atf-3 0xfdcd0000 ... sha256(d7aa45eb18...) + OK
## Checking optee 0x08400000 ... sha256(b8cddafab0...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 222.321 ms
INFO: Preloader serial: 7
I/TC:
I/TC: Start rockchip platform init
I/TC: Rockchip release version: 1.0
I/TC: OP-TEE version: 3.6.0-307-g0b06ae94 #1 Fri May 7 01:52:27 UTC 2021
aarch64
I/TC: Initialized
U-Boot 2017.09 (Nov 15 2023 - 08:31:01 +0100)
Model: Rockchip RK3568 Evaluation Board
PreSerial: 7, raw, 0xfe6b0000
DRAM: 2 GiB
Sysmem: init
Relocation Offset: 7d39d000, fdt: 7b9f9498
Using default environment
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
No misc partition
boot mode: None
FIT: No boot partition
No resource partition
Failed to load DTB
I2c0 speed: 100000Hz
rk8xx_read: read reg 0xed failed, ret=-121
rk8xx_read: read reg 0xed failed, ret=-121
of_get_regulator: Get (pmuio1-supply) regulator:
/i2c@fdd40000/pmic@20/regulators/LDO_REG1
rk8xx_read: read reg 0xed failed, ret=-121
of_get_regulator: Get (pmuio2-supply) regulator:
/i2c@fdd40000/pmic@20/regulators/LDO_REG1
rk8xx_read: read reg 0xed failed, ret=-121
of_get_regulator: Get (vccio1-supply) regulator:
/i2c@fdd40000/pmic@20/regulators/SWITCH_1
rk8xx_read: read reg 0xed failed, ret=-121
of_get_regulator: Get (vccio4-supply) regulator:
/i2c@fdd40000/pmic@20/regulators/DCDC_RE1
rk8xx_read: read reg 0xed failed, ret=-121
of_get_regulator: Get (vccio6-supply) regulator:
/i2c@fdd40000/pmic@20/regulators/SWITCH_1
rk8xx_read: read reg 0xed failed, ret=-121
of_get_regulator: Get (vccio7-supply) regulator:
/i2c@fdd40000/pmic@20/regulators/SWITCH_1
io-domain: OK
Model: Rockchip RK3566 EVB2 LP4X V10 Board
rk8xx_read: read reg 0xed failed, ret=-121
rk8xx_read: read reg 0xed failed, ret=-121
No resource partition
No file: logo.bmp
failed to display uboot logo
board_late_init init
rkgtc board late init
get_ethaddr_from_eeprom
addr:
ret:0 mac_addr: AC:DB:DA:63:CC:DF
EEPROM: GENIATECH!
EEPROM: XPI3566Z23390003
EEPROM: RE:DA:CT:ED
get ethaddr exist
mac_addr:RE:DA:CT:ED
etneaddr-buf:RE:DA:CT:ED
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
apll 816000 KHz
dpll 528000 KHz
gpll 1188000 KHz
cpll 1000000 KHz
npll 1200000 KHz
vpll 24000 KHz
hpll 24000 KHz
ppll 200000 KHz
armclk 816000 KHz
aclk_bus 150000 KHz
pclk_bus 100000 KHz
aclk_top_high 500000 KHz
aclk_top_low 400000 KHz
hclk_top 150000 KHz
pclk_top 100000 KHz
aclk_perimid 300000 KHz
hclk_perimid 150000 KHz
pclk_pmu 100000 KHz
Net: No ethernet found.
Hit key to stop autoboot('CTRL+C'): 0
## Booting FIT Image FIT: No boot partition
FIT: No FIT image
Could not find misc partition
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
android_image_load_by_partname: Can't find part: boot
Android image load failed
Android boot failed, error -1.
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 10
switch to partitions #0, OK
mmc0(part 0) is current device
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
starting USB...
Bus dwc3@fcc00000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus dwc3@fd000000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus dwc3@fcc00000 for devices... 1 USB Device(s) found
scanning bus dwc3@fd000000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Device 0: unknown device
No ethernet found.
missing environment variable: pxeuuid
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/000
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/00
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/0
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm-rockchip
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default-arm
No ethernet found.
missing environment variable: bootfile
Retrieving file: pxelinux.cfg/default
No ethernet found.
Config file not found
No ethernet found.
No ethernet found.
=> mmc part
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00004000 0x00005fff "uboot"
attrs: 0x0000000000000000
type: 8dcd1602-5214-43f9-ffef-c49a4ee450b7
guid: 5a30833f-8c43-47b1-a41d-84d40883d0c6
2 0x00028000 0x00067fff "EFI"
attrs: 0x0000000000000000
type: 1124e418-9008-41f8-9e3d-8d872216c8a1
guid: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
3 0x00078000 0x00c77fff "rootfs"
attrs: 0x0000000000000000
type: fbd4486a-e42c-448d-d4e9-7f5c324a7843
guid: 824cc7a0-36a8-11e3-890a-952519ad3f61
4 0x00cb8000 0x00e8ffde "userdata"
attrs: 0x0000000000000000
type: bbaf4f47-230d-45b6-feae-e4b35f300b00
guid: 824cc7a0-36a8-11e3-890a-952519ad3f62
=> load mmc 0:2 ${fdt_addr_r} dtb_from_linux.dtb
reading dtb_from_linux.dtb
110592 bytes read in 11 ms (9.6 MiB/s)
=> load mmc 0:2 ${kernel_addr_r} efi/boot/bootaa64.efi
reading efi/boot/bootaa64.efi
219050 bytes read in 37 ms (5.6 MiB/s)
=> bootefi ${kernel_addr_r} ${fdt_addr_r}
## Starting EFI application at 00a80000 ...
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 10
Scanning disk dw...@fe2b0000.blk...
MMC: block number 0x1 exceeds max(0x0)
MMC: block number 0x1 exceeds max(0x0)
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 51
Scanning disk dw...@fe2c0000.blk...
MMC: block number 0x1 exceeds max(0x0)
MMC: block number 0x1 exceeds max(0x0)
unknown raw ID 7be01208
Scanning disk fl...@0.blk...
unrecognized JEDEC id bytes: 00, 00, 00
Scanning disk fl...@1.blk...
Scanning disk sd...@fe310000.blk...
Scanning disk na...@fe330000.blk...
Found 6 disks
No resource partition
No file: logo_kernel.bmp
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0x80000000 (size: 0x76c00000)
disks: sd0* sd1 sd2 sd3 sd4
>> OpenBSD/arm64 BOOTAA64 1.18
boot> set device sd3
boot> boot
cannot open sd3:/etc/random.seed: bad partition
booting sd3:/bsd: open sd3:/bsd: bad partition
failed(99). will try /bsd
boot>
----------------
Mizsei Zoltán írta 2023. okt.. 31, K-n 10:16 órakor:
> Hi, a short question:
>
> Is it possible to boot OpenBSD with the factory uboot bootloader or do
> we need an own-built Uboot for that? If an own built one is needed, can
> you instruct me, what features is necessary to be able to boot OBSD?
>
> Thank You very much!
>
> Best Regards,
> -- Zoltán
>
> Mizsei Zoltán írta 2023. okt.. 31, K-n 08:09 órakor:
>> In case you are interested, i document my jurney here (it is work in
>> progress):
>> https://extrowerk.com/2023-10-30/Geniatech-XPI-3566-ZERO-SBC.html
>>
>> Best regards,
>> --Z--
>>
>> Mizsei Zoltán írta 2023. okt.. 18, Sze-n 07:43 órakor:
>>> Hi,
>>>
>>> i have just received an Geniatech XPI-3566 Zero SBC [1], which is a n
>>> RPi ZERO W2 alternative:
>>>
>>> Specs:
>>> CPU: 4xARM A55 max. 1,8Ghz
>>> GPU: ARM G52 2EE GPU
>>> RAM: 512M-8GB LPDDR4 (mine have 2G)
>>> SD card: NO !!!
>>> eMMC: 8GB eMMC
>>> wlan: AMPAK AP6256
>>>
>>> The board comes with Debian preinstalled on the eMMC. The board boots,
>>> so it is in good working condition.
>>>
>>> On the first glance it should be moderately easily to get it work with
>>> OBSD, as the CPU and the wlan chip seems to be supported, and as far as
>>> i know the PM chip should be also supported.
>>> However there is no SD-Card slot and the eMMC is not removeable. AFAIK
>>> the RockChip boards uses a propertiary (?) protocol to flash the eMMC
>>> chip.So theoretically i should somehow repace the factory-default
>>> partitions with an OBSD root image using the official flasher (using
>>> windows).
>>>
>>> I would like tho use the board with HDMI output, and AFAIK for that
>>> EDK2 or uboot EFI support would be required.
>>> I haven't had yet enough time to check if the uboot have efi
>>> compatibility.
>>>
>>> I have found a port of Tianocore EDK II to Rockchip RK356x based SBCs,
>>> which lists HDMI supported with OpenBSD [1]. I did not tested it yet,
>>> as this should be flashed onto the eMMC, and i don't want to risk a
>>> brick.
>>> Possibly the EDK2 port needs to be adjusted first to support this
>>> specific board. Also maybe just maybe there is a USB support in the
>>> factory-default uboot, and maybe it is possible to chainload the EDK2
>>> from a USB disk.
>>> Maybe i am completely wrong here.
>>>
>>> For more info see the attached dmesg from the factory-default linux.
>>>
>>> Do somebody have the same or similar board? Can sombodíy give me some hints?
>>>
>>> Thank You very much!
>>>
>>> Best Regards,
>>> -- Zoltan
>>> http://extrowerk.com
>>>
>>> [1] : https://www.geniatech.com/product/xpi-3566-zero/
>>> [2] : https://github.com/jaredmcneill/quartz64_uefi
>>>
>>>
>>> DMESG from linux:
>>> [ 1.148647] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
>>> [ 1.148671] Linux version 5.10.160 (geniatech@ubuntu22)
>>> (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile
>>> Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU
>>> Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29))
>>> 2.36.1.20210621) #1 SMP Fri Sep 8 10:45:44 CST 2023
>>> [ 1.153011] Machine model: Rockchip RK3566 EVB2 LP4X V10 Board
>>> [ 1.153079] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options
>>> '')
>>> [ 1.157370] printk: bootconsole [uart8250] enabled
>>> [ 1.158806] efi: UEFI not found.
>>> [ 1.194770] Zone ranges:
>>> [ 1.195027] DMA [mem 0x0000000000200000-0x000000007fffffff]
>>> [ 1.195617] DMA32 empty
>>> [ 1.195891] Normal empty
>>> [ 1.196166] Movable zone start for each node
>>> [ 1.196570] Early memory node ranges
>>> [ 1.196910] node 0: [mem 0x0000000000200000-0x00000000083fffff]
>>> [ 1.197504] node 0: [mem 0x0000000009400000-0x000000007fffffff]
>>> [ 1.198100] Initmem setup node 0 [mem
>>> 0x0000000000200000-0x000000007fffffff]
>>> [ 1.198768] On node 0 totalpages: 519680
>>> [ 1.198773] DMA zone: 8184 pages used for memmap
>>> [ 1.198775] DMA zone: 0 pages reserved
>>> [ 1.198778] DMA zone: 519680 pages, LIFO batch:63
>>> [ 1.214084] cma: Reserved 16 MiB at 0x000000007e800000
>>> [ 1.214658] psci: probing for conduit method from DT.
>>> [ 1.215150] psci: PSCIv1.1 detected in firmware.
>>> [ 1.215587] psci: Using standard PSCI v0.2 function IDs
>>> [ 1.216085] psci: Trusted OS migration not required
>>> [ 1.216550] psci: SMC Calling Convention v1.2
>>> [ 1.217352] percpu: Embedded 30 pages/cpu s83480 r8192 d31208 u122880
>>> [ 1.217990] pcpu-alloc: s83480 r8192 d31208 u122880 alloc=30*4096
>>> [ 1.217997] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
>>> [ 1.218079] Detected VIPT I-cache on CPU0
>>> [ 1.218501] CPU features: detected: GIC system register CPU interface
>>> [ 1.219112] CPU features: detected: Virtualization Host Extensions
>>> [ 1.219703] CPU features: detected: ARM errata 1165522, 1319367, or
>>> 1530923
>>> [ 1.220369] alternatives: patching kernel code
>>> [ 1.222926] Built 1 zonelists, mobility grouping on. Total pages:
>>> 511496
>>> [ 1.223577] Kernel command line: storagemedia=emmc
>>> androidboot.storagemedia=emmc androidboot.mode=normal
>>> androidboot.verifiedbootstate=orange rw rootwait
>>> earlycon=uart8250,mmio32,0xfe660000 console=ttyFIQ0
>>> root=PARTUUID=614e0000-0000
>>> [ 1.226258] Dentry cache hash table entries: 262144 (order: 9,
>>> 2097152 bytes, linear)
>>> [ 1.227246] Inode-cache hash table entries: 131072 (order: 8,
>>> 1048576 bytes, linear)
>>> [ 1.227981] mem auto-init: stack:off, heap alloc:off, heap free:off
>>> [ 1.256114] Memory: 1985732K/2078720K available (18112K kernel code,
>>> 3346K rwdata, 6044K rodata, 6592K init, 530K bss, 76604K reserved,
>>> 16384K cma-reserved)
>>> [ 1.257570] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4,
>>> Nodes=1
>>> [ 1.258221] ftrace: allocating 56170 entries in 220 pages
>>> [ 1.336694] ftrace: allocated 220 pages with 5 groups
>>> [ 1.337523] rcu: Hierarchical RCU implementation.
>>> [ 1.337978] rcu: RCU event tracing is enabled.
>>> [ 1.338409] rcu: RCU restricting CPUs from NR_CPUS=8 to
>>> nr_cpu_ids=4.
>>> [ 1.339028] Rude variant of Tasks RCU enabled.
>>> [ 1.339459] rcu: RCU calculated value of scheduler-enlistment delay
>>> is 30 jiffies.
>>> [ 1.340175] rcu: Adjusting geometry for rcu_fanout_leaf=16,
>>> nr_cpu_ids=4
>>> [ 1.345602] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
>>> [ 1.347364] GICv3: GIC: Using split EOI/Deactivate mode
>>> [ 1.347872] GICv3: 320 SPIs implemented
>>> [ 1.348236] GICv3: 0 Extended SPIs implemented
>>> [ 1.348693] GICv3: Distributor has no Range Selector support
>>> [ 1.349235] GICv3: 16 PPIs implemented
>>> [ 1.349627] GICv3: CPU0: found redistributor 0 region
>>> 0:0x00000000fd460000
>>> [ 1.350401] ITS [mem 0xfd440000-0xfd45ffff]
>>> [ 1.350873] ITS@0x00000000fd440000: allocated 8192 Devices @25d0000
>>> (indirect, esz 8, psz 64K, shr 0)
>>> [ 1.351777] ITS@0x00000000fd440000: allocated 32768 Interrupt
>>> Collections @25e0000 (flat, esz 2, psz 64K, shr 0)
>>> [ 1.352744] ITS: using cache flushing for cmd queue
>>> [ 1.353506] GICv3: using LPI property table @0x00000000025f0000
>>> [ 1.354182] GIC: using cache flushing for LPI property table
>>> [ 1.354724] GICv3: CPU0: using allocated LPI pending table
>>> @0x0000000002600000
>>> [ 1.385166] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
>>> [ 1.385760] clocksource: arch_sys_counter: mask: 0xffffffffffffff
>>> max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
>>> [ 1.386787] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps
>>> every 4398046511097ns
>>> [ 1.388366] Console: colour dummy device 80x25
>>> [ 1.388821] Calibrating delay loop (skipped), value calculated using
>>> timer frequency.. 48.00 BogoMIPS (lpj=80000)
>>> [ 1.389798] pid_max: default: 32768 minimum: 301
>>> [ 1.390373] Mount-cache hash table entries: 4096 (order: 3, 32768
>>> bytes, linear)
>>> [ 1.391083] Mountpoint-cache hash table entries: 4096 (order: 3,
>>> 32768 bytes, linear)
>>> [ 1.393277] rcu: Hierarchical SRCU implementation.
>>> [ 1.394488] Platform MSI: interrupt-controller@fd440000 domain
>>> created
>>> [ 1.395516] PCI/MSI:
>>> /interrupt-controller@fd400000/interrupt-controller@fd440000 domain
>>> created
>>> [ 1.396585] EFI services will not be available.
>>> [ 1.397369] smp: Bringing up secondary CPUs ...
>>> [ 1.399090] Detected VIPT I-cache on CPU1
>>> [ 1.399124] GICv3: CPU1: found redistributor 100 region
>>> 0:0x00000000fd480000
>>> [ 1.399145] GICv3: CPU1: using allocated LPI pending table
>>> @0x0000000002610000
>>> [ 1.399197] CPU1: Booted secondary processor 0x0000000100
>>> [0x412fd050]
>>> [ 1.400538] Detected VIPT I-cache on CPU2
>>> [ 1.400567] GICv3: CPU2: found redistributor 200 region
>>> 0:0x00000000fd4a0000
>>> [ 1.400585] GICv3: CPU2: using allocated LPI pending table
>>> @0x0000000002620000
>>> [ 1.400623] CPU2: Booted secondary processor 0x0000000200
>>> [0x412fd050]
>>> [ 1.401916] Detected VIPT I-cache on CPU3
>>> [ 1.401940] GICv3: CPU3: found redistributor 300 region
>>> 0:0x00000000fd4c0000
>>> [ 1.401957] GICv3: CPU3: using allocated LPI pending table
>>> @0x0000000002630000
>>> [ 1.401993] CPU3: Booted secondary processor 0x0000000300
>>> [0x412fd050]
>>> [ 1.402085] smp: Brought up 1 node, 4 CPUs
>>> [ 1.409548] SMP: Total of 4 processors activated.
>>> [ 1.409997] CPU features: detected: Privileged Access Never
>>> [ 1.410525] CPU features: detected: User Access Override
>>> [ 1.411029] CPU features: detected: 32-bit EL0 Support
>>> [ 1.411516] CPU features: detected: Common not Private translations
>>> [ 1.412108] CPU features: detected: RAS Extension Support
>>> [ 1.412620] CPU features: detected: Data cache clean to the PoU not
>>> required for I/D coherence
>>> [ 1.413442] CPU features: detected: CRC32 instructions
>>> [ 1.413930] CPU features: detected: Speculative Store Bypassing Safe
>>> (SSBS)
>>> [ 1.414589] CPU features: detected: RCpc load-acquire (LDAPR)
>>> [ 1.415208] CPU: All CPU(s) started at EL2
>>> [ 1.416686] devtmpfs: initialized
>>> [ 1.431695] Registered cp15_barrier emulation handler
>>> [ 1.432195] Registered setend emulation handler
>>> [ 1.432790] clocksource: jiffies: mask: 0xffffffff max_cycles:
>>> 0xffffffff, max_idle_ns: 6370867519511994 ns
>>> [ 1.433724] futex hash table entries: 1024 (order: 4, 65536 bytes,
>>> linear)
>>> [ 1.434916] pinctrl core: initialized pinctrl subsystem
>>> [ 1.435968] DMI not present or invalid.
>>> [ 1.436749] NET: Registered protocol family 16
>>> [ 1.438908] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic
>>> allocations
>>> [ 1.439754] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for
>>> atomic allocations
>>> [ 1.442221] Registered FIQ tty driver
>>> [ 1.442908] thermal_sys: Registered thermal governor 'fair_share'
>>> [ 1.442914] thermal_sys: Registered thermal governor 'step_wise'
>>> [ 1.443522] thermal_sys: Registered thermal governor 'user_space'
>>> [ 1.444092] thermal_sys: Registered thermal governor
>>> 'power_allocator'
>>> [ 1.444951] thermal thermal_zone1: power_allocator:
>>> sustainable_power will be estimated
>>> [ 1.446383] cpuidle: using governor menu
>>> [ 1.447034] hw-breakpoint: found 6 breakpoint and 4 watchpoint
>>> registers.
>>> [ 1.447802] ASID allocator initialised with 65536 entries
>>> [ 1.450755] ramoops: dmesg-0 0x20000@0x0000000000110000
>>> [ 1.451270] ramoops: console 0x80000@0x0000000000130000
>>> [ 1.451786] ramoops: pmsg 0x50000@0x00000000001b0000
>>> [ 1.452632] printk: console [ramoops-1] enabled
>>> [ 1.453065] pstore: Registered ramoops as persistent store backend
>>> [ 1.453670] ramoops: using 0xf0000@0x110000, ecc: 0
>>> [ 1.481321] rockchip-gpio fdd60000.gpio0: probed
>>> /pinctrl/gpio0@fdd60000
>>> [ 1.482484] rockchip-gpio fe740000.gpio1: probed
>>> /pinctrl/gpio1@fe740000
>>> [ 1.483564] rockchip-gpio fe750000.gpio2: probed
>>> /pinctrl/gpio2@fe750000
>>> [ 1.484703] rockchip-gpio fe760000.gpio3: probed
>>> /pinctrl/gpio3@fe760000
>>> [ 1.485874] rockchip-gpio fe770000.gpio4: probed
>>> /pinctrl/gpio4@fe770000
>>> [ 1.486593] rockchip-pinctrl pinctrl: probed pinctrl
>>> [ 1.508349] fiq_debugger fiq_debugger.0: IRQ fiq not found
>>> [ 1.508899] fiq_debugger fiq_debugger.0: IRQ wakeup not found
>>> [ 1.509452] fiq_debugger_probe: could not install nmi irq handler
>>> [ 1.510122] printk: console [ttyFIQ0] enabled
>>> [ 1.510550] printk: bootconsole [uart8250] disabled
>>> [ 1.511229] Registered fiq debugger ttyFIQ0
>>> [ 1.511977] vcc3v3_sys: supplied by dc_12v
>>> [ 1.512240] vcc5v0_sys: supplied by dc_12v
>>> [ 1.512513] vcc5v0_usb: supplied by dc_12v
>>> [ 1.512883] vcc5v0_host: supplied by vcc5v0_usb
>>> [ 1.513334] vcc5v0_otg: supplied by vcc5v0_usb
>>> [ 1.514355] vcc3v3_pcie: supplied by dc_12v
>>> [ 1.515203] iommu: Default domain type: Translated
>>> [ 1.518473] SCSI subsystem initialized
>>> [ 1.518522] libata version 3.00 loaded.
>>> [ 1.518680] usbcore: registered new interface driver usbfs
>>> [ 1.518729] usbcore: registered new interface driver hub
>>> [ 1.518769] usbcore: registered new device driver usb
>>> [ 1.518856] mc: Linux media interface: v0.10
>>> [ 1.518884] videodev: Linux video capture interface: v2.00
>>> [ 1.518958] pps_core: LinuxPPS API ver. 1 registered
>>> [ 1.518967] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
>>> Rodolfo Giometti <giome...@linux.it>
>>> [ 1.518984] PTP clock support registered
>>> [ 1.519609] arm-scmi firmware:scmi: SCMI Notifications - Core
>>> Enabled.
>>> [ 1.519679] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:'
>>> Firmware version 0x0
>>> [ 1.521610] Advanced Linux Sound Architecture Driver Initialized.
>>> [ 1.522026] Bluetooth: Core ver 2.22
>>> [ 1.522063] NET: Registered protocol family 31
>>> [ 1.522071] Bluetooth: HCI device and connection manager initialized
>>> [ 1.522085] Bluetooth: HCI socket layer initialized
>>> [ 1.522096] Bluetooth: L2CAP socket layer initialized
>>> [ 1.522115] Bluetooth: SCO socket layer initialized
>>> [ 1.522586] rockchip-cpuinfo cpuinfo: SoC : 35662000
>>> [ 1.522600] rockchip-cpuinfo cpuinfo: Serial :
>>> 3cb4e04f0cd3ac4f
>>> [ 1.523306] clocksource: Switched to clocksource arch_sys_counter
>>> [ 1.986686] NET: Registered protocol family 2
>>> [ 1.986910] IP idents hash table entries: 32768 (order: 6, 262144
>>> bytes, linear)
>>> [ 1.988141] tcp_listen_portaddr_hash hash table entries: 1024
>>> (order: 2, 16384 bytes, linear)
>>> [ 1.988184] TCP established hash table entries: 16384 (order: 5,
>>> 131072 bytes, linear)
>>> [ 1.988279] TCP bind hash table entries: 16384 (order: 6, 262144
>>> bytes, linear)
>>> [ 1.988499] TCP: Hash tables configured (established 16384 bind
>>> 16384)
>>> [ 1.988625] UDP hash table entries: 1024 (order: 3, 32768 bytes,
>>> linear)
>>> [ 1.988662] UDP-Lite hash table entries: 1024 (order: 3, 32768
>>> bytes, linear)
>>> [ 1.988830] NET: Registered protocol family 1
>>> [ 1.989309] RPC: Registered named UNIX socket transport module.
>>> [ 1.989321] RPC: Registered udp transport module.
>>> [ 1.989328] RPC: Registered tcp transport module.
>>> [ 1.989334] RPC: Registered tcp NFSv4.1 backchannel transport module.
>>> [ 1.990280] PCI: CLS 0 bytes, default 64
>>> [ 1.992575] rockchip-thermal fe710000.tsadc: tsadc is probed
>>> successfully!
>>> [ 1.993623] hw perfevents: enabled with armv8_cortex_a55 PMU driver,
>>> 7 counters available
>>> [ 1.997614] Initialise system trusted keyrings
>>> [ 1.997782] workingset: timestamp_bits=62 max_order=19 bucket_order=0
>>> [ 2.001667] squashfs: version 4.0 (2009/01/31) Phillip Lougher
>>> [ 2.002209] NFS: Registering the id_resolver key type
>>> [ 2.002247] Key type id_resolver registered
>>> [ 2.002256] Key type id_legacy registered
>>> [ 2.002288] ntfs: driver 2.1.32 [Flags: R/O].
>>> [ 2.002490] jffs2: version 2.2. (NAND) \xc2\xa9 2001-2006 Red Hat,
>>> Inc.
>>> [ 2.002737] fuse: init (API version 7.32)
>>> [ 2.003025] SGI XFS with security attributes, no debug enabled
>>> [ 2.038140] NET: Registered protocol family 38
>>> [ 2.038173] Key type asymmetric registered
>>> [ 2.038183] Asymmetric key parser 'x509' registered
>>> [ 2.038228] Block layer SCSI generic (bsg) driver version 0.4 loaded
>>> (major 242)
>>> [ 2.038239] io scheduler mq-deadline registered
>>> [ 2.038246] io scheduler kyber registered
>>> [ 2.038875] rockchip-csi2-dphy-hw fe870000.csi2-dphy-hw: csi2 dphy
>>> hw probe successfully!
>>> [ 2.039618] rockchip-csi2-dphy csi2-dphy1: csi2 dphy1 probe
>>> successfully!
>>> [ 2.048935] pwm-backlight backlight: supply power not found, using
>>> dummy regulator
>>> [ 2.049412] pwm-backlight backlight1: supply power not found, using
>>> dummy regulator
>>> [ 2.049936] iep: Module initialized.
>>> [ 2.054054] dma-pl330 fe530000.dmac: Loaded driver for PL330
>>> DMAC-241330
>>> [ 2.054094] dma-pl330 fe530000.dmac: DBUFF-128x8bytes Num_Chans-8
>>> Num_Peri-32 Num_Events-16
>>> [ 2.055865] dma-pl330 fe550000.dmac: Loaded driver for PL330
>>> DMAC-241330
>>> [ 2.055892] dma-pl330 fe550000.dmac: DBUFF-128x8bytes Num_Chans-8
>>> Num_Peri-32 Num_Events-16
>>> [ 2.056579] rockchip-pvtm fde00000.pvtm: pvtm@0 probed
>>> [ 2.056748] rockchip-pvtm fde80000.pvtm: pvtm@1 probed
>>> [ 2.056865] rockchip-pvtm fde90000.pvtm: pvtm@2 probed
>>> [ 2.057442] rockchip-system-monitor rockchip-system-monitor: system
>>> monitor probe
>>> [ 2.058160] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not
>>> active.
>>> [ 2.058416] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
>>> [ 2.059407] fe650000.serial: ttyS1 at MMIO 0xfe650000 (irq = 55,
>>> base_baud = 1500000) is a 16550A
>>> [ 2.060001] fe680000.serial: ttyS4 at MMIO 0xfe680000 (irq = 56,
>>> base_baud = 1500000) is a 16550A
>>> [ 2.060509] fe6d0000.serial: ttyS9 at MMIO 0xfe6d0000 (irq = 57,
>>> base_baud = 1500000) is a 16550A
>>> [ 2.062662] random: crng init done
>>> [ 2.063407] rockchip-vop2 fe040000.vop: Adding to iommu group 7
>>> [ 2.069729] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign
>>> plane mask: 0x3f, primary plane phy id: 4
>>> [ 2.069773] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign
>>> plane mask: 0x0, primary plane phy id: -1
>>> [ 2.069785] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign
>>> plane mask: 0x0, primary plane phy id: -1
>>> [ 2.069922] rockchip-vop2 fe040000.vop: [drm:vop2_bind]
>>> Cluster0-win0 as cursor plane for vp0
>>> [ 2.070024] [drm] failed to init overlay plane Cluster0-win1
>>> [ 2.070119] rockchip-drm display-subsystem: bound fe040000.vop (ops
>>> 0xffffffc0092bcd98)
>>> [ 2.070417] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX
>>> controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
>>> [ 2.070968] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare
>>> HDMI I2C bus driver
>>> [ 2.071177] dwhdmi-rockchip fe0a0000.hdmi: IRQ index 1 not found
>>> [ 2.071559] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops
>>> 0xffffffc0092cb900)
>>> [ 2.198563] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb
>>> frame buffer device
>>> [ 2.199324] [drm] Initialized rockchip 3.0.0 20140818 for
>>> display-subsystem on minor 0
>>> [ 2.203963] input: hdmi_cec_key as
>>> /devices/platform/fe0a0000.hdmi/dw-hdmi-cec.1.auto/input/input0
>>> [ 2.204731] mali fde60000.gpu: Kernel DDK version g18p0-01eac0
>>> [ 2.204817] cacheinfo: Unable to detect cache hierarchy for CPU 0
>>> [ 2.204860] mali fde60000.gpu: bin=0
>>> [ 2.204926] mali fde60000.gpu: leakage=6
>>> [ 2.204995] mali fde60000.gpu: pvtm = 84490, from nvmem
>>> [ 2.205017] mali fde60000.gpu: pvtm-volt-sel=1
>>> [ 2.205452] brd: module loaded
>>> [ 2.205624] mali fde60000.gpu: avs=0
>>> [ 2.205656] W : [File] :
>>> drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] :
>>> 143; [Func] : kbase_platform_rk_init(); power-off-delay-ms not
>>> available.
>>> [ 2.206013] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0
>>> status 0
>>> [ 2.206090] mali fde60000.gpu: No priority control manager is
>>> configured
>>> [ 2.206295] mali fde60000.gpu: No memory group manager is configured
>>> [ 2.208228] mali fde60000.gpu: l=0 h=2147483647 hyst=5000
>>> l_limit=700000000 h_limit=0 h_table=0
>>> [ 2.209104] mali fde60000.gpu: Probed as mali0
>>> [ 2.211441] loop: module loaded
>>> [ 2.211798] zram: Added device: zram0
>>> [ 2.212023] lkdtm: No crash points registered, enable through debugfs
>>> [ 2.215819] rockchip-spi fe640000.spi: no high_speed pinctrl state
>>> [ 2.215909] spi_dev@0 enforce active low on chipselect handle
>>> [ 2.216607] rockchip-spi fe640000.spi: probed, poll=0, rsd=0,
>>> cs-inactive=0, ready=0
>>> [ 2.218149] spi-nand spi4.0: unknown raw ID 00000000
>>> [ 2.218185] spi-nand: probe of spi4.0 failed with error -524
>>> [ 2.220197] usbcore: registered new interface driver rtl8150
>>> [ 2.220258] usbcore: registered new interface driver r8152
>>> [ 2.230950] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
>>> Driver
>>> [ 2.230990] ehci-pci: EHCI PCI platform driver
>>> [ 2.231070] ehci-platform: EHCI generic platform driver
>>> [ 2.231325] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
>>> [ 2.231344] ohci-platform: OHCI generic platform driver
>>> [ 2.231923] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
>>> [ 2.232124] xhci-hcd xhci-hcd.4.auto: new USB bus registered,
>>> assigned bus number 1
>>> [ 2.232267] xhci-hcd xhci-hcd.4.auto: hcc params 0x0220fe64 hci
>>> version 0x110 quirks 0x0000200002010010
>>> [ 2.232330] xhci-hcd xhci-hcd.4.auto: irq 70, io mem 0xfd000000
>>> [ 2.232612] usb usb1: New USB device found, idVendor=1d6b,
>>> idProduct=0002, bcdDevice= 5.10
>>> [ 2.232624] usb usb1: New USB device strings: Mfr=3, Product=2,
>>> SerialNumber=1
>>> [ 2.232633] usb usb1: Product: xHCI Host Controller
>>> [ 2.232641] usb usb1: Manufacturer: Linux 5.10.160 xhci-hcd
>>> [ 2.232649] usb usb1: SerialNumber: xhci-hcd.4.auto
>>> [ 2.233067] hub 1-0:1.0: USB hub found
>>> [ 2.233113] hub 1-0:1.0: 1 port detected
>>> [ 2.233441] xhci-hcd xhci-hcd.4.auto: xHCI Host Controller
>>> [ 2.233590] xhci-hcd xhci-hcd.4.auto: new USB bus registered,
>>> assigned bus number 2
>>> [ 2.233609] xhci-hcd xhci-hcd.4.auto: Host supports USB 3.0
>>> SuperSpeed
>>> [ 2.233674] usb usb2: We don't know the algorithms for LPM for this
>>> host, disabling LPM.
>>> [ 2.233774] usb usb2: New USB device found, idVendor=1d6b,
>>> idProduct=0003, bcdDevice= 5.10
>>> [ 2.233785] usb usb2: New USB device strings: Mfr=3, Product=2,
>>> SerialNumber=1
>>> [ 2.233794] usb usb2: Product: xHCI Host Controller
>>> [ 2.233801] usb usb2: Manufacturer: Linux 5.10.160 xhci-hcd
>>> [ 2.233809] usb usb2: SerialNumber: xhci-hcd.4.auto
>>> [ 2.234190] hub 2-0:1.0: USB hub found
>>> [ 2.234227] hub 2-0:1.0: 1 port detected
>>> [ 2.234628] usbcore: registered new interface driver cdc_acm
>>> [ 2.234638] cdc_acm: USB Abstract Control Model driver for USB
>>> modems and ISDN adapters
>>> [ 2.234910] usbcore: registered new interface driver uas
>>> [ 2.234977] usbcore: registered new interface driver usb-storage
>>> [ 2.235060] usbcore: registered new interface driver
>>> usbserial_generic
>>> [ 2.235085] usbserial: USB Serial support registered for generic
>>> [ 2.235122] usbcore: registered new interface driver cp210x
>>> [ 2.235147] usbserial: USB Serial support registered for cp210x
>>> [ 2.235191] usbcore: registered new interface driver ftdi_sio
>>> [ 2.235216] usbserial: USB Serial support registered for FTDI USB
>>> Serial Device
>>> [ 2.235279] usbcore: registered new interface driver keyspan
>>> [ 2.235303] usbserial: USB Serial support registered for Keyspan -
>>> (without firmware)
>>> [ 2.235324] usbserial: USB Serial support registered for Keyspan 1
>>> port adapter
>>> [ 2.235344] usbserial: USB Serial support registered for Keyspan 2
>>> port adapter
>>> [ 2.235364] usbserial: USB Serial support registered for Keyspan 4
>>> port adapter
>>> [ 2.235401] usbcore: registered new interface driver option
>>> [ 2.235423] usbserial: USB Serial support registered for GSM modem
>>> (1-port)
>>> [ 2.235506] usbcore: registered new interface driver oti6858
>>> [ 2.235532] usbserial: USB Serial support registered for oti6858
>>> [ 2.235569] usbcore: registered new interface driver pl2303
>>> [ 2.235592] usbserial: USB Serial support registered for pl2303
>>> [ 2.235630] usbcore: registered new interface driver qcserial
>>> [ 2.235652] usbserial: USB Serial support registered for Qualcomm
>>> USB modem
>>> [ 2.235694] usbcore: registered new interface driver sierra
>>> [ 2.235717] usbserial: USB Serial support registered for Sierra USB
>>> modem
>>> [ 2.237058] usbcore: registered new interface driver usbtouchscreen
>>> [ 2.237567] i2c /dev entries driver
>>> [ 2.238510] at24 0-0050: supply vcc not found, using dummy regulator
>>> [ 2.239274] at24 0-0050: 256 byte 24c02 EEPROM, writable, 1
>>> bytes/write
>>> [ 2.239710] fan53555-regulator 0-001c: Failed to get chip ID!
>>> [ 2.241105] rk808 0-0020: failed to read the chip id at 0x17
>>> [ 2.243048] <<GTP-INF>>[gt1x_ts_probe:560] GTP Driver Version:
>>> V1.4<2015/07/10>
>>> [ 2.243072] <<GTP-INF>>[gt1x_ts_probe:561] GTP I2C Address: 0x14
>>> [ 2.243126] <<GTP-ERR>>[gt1x_parse_dt:341] vdd_ana not specified,
>>> fallback to power-supply
>>> [ 2.243464] <<GTP-INF>>[gt1x_parse_dt:348] Power Invert,no
>>> [ 2.243557] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET!
>>> [ 2.263320] ov5647 xclk
>>> [ 2.263373] ov5647 detect
>>> [ 2.313508] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
>>> [ 2.313527] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed!
>>> [ 2.313535] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET!
>>> [ 2.383478] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
>>> [ 2.383496] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed!
>>> [ 2.383503] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET!
>>> [ 2.430173] ov5647 2-0036: ov5647_write: i2c write error, reg: 103
>>> [ 2.432265] rkisp_hw fdff0000.rkisp: Adding to iommu group 6
>>> [ 2.432497] rkisp_hw fdff0000.rkisp: is_thunderboot: 0
>>> [ 2.432512] rkisp_hw fdff0000.rkisp: max input:0x0@0fps
>>> [ 2.432542] rkisp_hw fdff0000.rkisp: can't request region for
>>> resource [mem 0xfdff0000-0xfdffffff]
>>> [ 2.432751] rkisp_hw fdff0000.rkisp: no find phandle sram
>>> [ 2.433227] rkisp rkisp-vir0: rkisp driver version: v02.02.02
>>> [ 2.433360] rkisp rkisp-vir0: No memory-region-thunderboot specified
>>> [ 2.433569] rkisp rkisp-vir0: Entity type for entity
>>> rkisp-isp-subdev was not initialized!
>>> [ 2.433591] rkisp rkisp-vir0: Entity type for entity
>>> rkisp-csi-subdev was not initialized!
>>> [ 2.435966] usbcore: registered new interface driver uvcvideo
>>> [ 2.435985] USB Video Class driver (1.1.1)
>>> [ 2.437528] Bluetooth: HCI UART driver ver 2.3
>>> [ 2.437548] Bluetooth: HCI UART protocol H4 registered
>>> [ 2.437556] Bluetooth: HCI UART protocol ATH3K registered
>>> [ 2.437618] usbcore: registered new interface driver bfusb
>>> [ 2.437661] usbcore: registered new interface driver btusb
>>> [ 2.438169] cpu cpu0: leakage=17
>>> [ 2.438218] cpu cpu0: pvtm = 84490, from nvmem
>>> [ 2.438235] cpu cpu0: pvtm-volt-sel=1
>>> [ 2.440137] sdhci: Secure Digital Host Controller Interface driver
>>> [ 2.440156] sdhci: Copyright(c) Pierre Ossman
>>> [ 2.440163] Synopsys Designware Multimedia Card Interface Driver
>>> [ 2.440755] sdhci-pltfm: SDHCI platform and OF driver helper
>>> [ 2.441136] dwmmc_rockchip fe2c0000.dwmmc: No normal pinctrl state
>>> [ 2.441153] dwmmc_rockchip fe2c0000.dwmmc: No idle pinctrl state
>>> [ 2.441280] dwmmc_rockchip fe2c0000.dwmmc: IDMAC supports 32-bit
>>> address mode.
>>> [ 2.441310] dwmmc_rockchip fe2c0000.dwmmc: Using internal DMA
>>> controller.
>>> [ 2.441324] dwmmc_rockchip fe2c0000.dwmmc: Version ID is 270a
>>> [ 2.441393] dwmmc_rockchip fe2c0000.dwmmc: DW MMC controller at irq
>>> 41,32 bit host data width,256 deep fifo
>>> [ 2.441707] dwmmc_rockchip fe2c0000.dwmmc: allocated mmc-pwrseq
>>> [ 2.441725] mmc_host mmc2: card is non-removable.
>>> [ 2.442199] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not
>>> active.
>>> [ 2.442293] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
>>> [ 2.443069] cryptodev: driver 1.12 loaded.
>>> [ 2.443146] hid: raw HID events driver (C) Jiri Kosina
>>> [ 2.443610] usbcore: registered new interface driver usbhid
>>> [ 2.443622] usbhid: USB HID core driver
>>> [ 2.447359] usbcore: registered new interface driver snd-usb-audio
>>> [ 2.453530] Initializing XFRM netlink socket
>>> [ 2.453668] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
>>> [ 2.453683] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed!
>>> [ 2.453691] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET!
>>> [ 2.453796] mmc_host mmc2: Bus speed (slot 0) = 375000Hz (slot req
>>> 400000Hz, actual 375000HZ div = 0)
>>> [ 2.453970] NET: Registered protocol family 10
>>> [ 2.454782] Segment Routing with IPv6
>>> [ 2.454845] NET: Registered protocol family 17
>>> [ 2.454871] NET: Registered protocol family 15
>>> [ 2.455035] Bluetooth: RFCOMM socket layer initialized
>>> [ 2.455072] Bluetooth: RFCOMM ver 1.11
>>> [ 2.455102] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
>>> [ 2.455117] Bluetooth: HIDP socket layer initialized
>>> [ 2.455161] [BT_RFKILL]: Enter rfkill_rk_init
>>> [ 2.455169] [WLAN_RFKILL]: Enter rfkill_wlan_init
>>> [ 2.455724] [WLAN_RFKILL]: Enter rfkill_wlan_probe
>>> [ 2.455786] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type =
>>> ap6256
>>> [ 2.455795] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power
>>> control.
>>> [ 2.455803] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power
>>> controled by gpio.
>>> [ 2.455828] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,poweren_gpio
>>> = 74 flags = 0.
>>> [ 2.455852] [WLAN_RFKILL]: wlan_platdata_parse_dt:
>>> WIFI,host_wake_irq = 74, flags = 0.
>>> [ 2.455864] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk
>>> not found !
>>> [ 2.455872] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
>>> [ 2.455880] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
>>> [ 2.455888] [WLAN_RFKILL]: Exit rfkill_wlan_probe
>>> [ 2.456662] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property:
>>> uart_rts_gpios = 77.
>>> [ 2.456693] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property:
>>> BT,reset_gpio = 79.
>>> [ 2.456710] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property:
>>> BT,wake_gpio = 81.
>>> [ 2.456724] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property:
>>> BT,wake_host_irq = 80.
>>> [ 2.456794] [BT_RFKILL]: Request irq for bt wakeup host
>>> [ 2.456900] [BT_RFKILL]: ** disable irq
>>> [ 2.457005] [BT_RFKILL]: bt_default device registered.
>>> [ 2.457137] Key type dns_resolver registered
>>> [ 2.458535] gc8034 2-0037: driver version: 00.01.09
>>> [ 2.458587] gc8034 2-0037: Failed to get power-gpios, maybe no use
>>> [ 2.458741] gc8034 2-0037: supply dovdd not found, using dummy
>>> regulator
>>> [ 2.458880] gc8034 2-0037: supply dvdd not found, using dummy
>>> regulator
>>> [ 2.458928] gc8034 2-0037: supply avdd not found, using dummy
>>> regulator
>>> [ 2.458979] gc8034 2-0037: lane_num(4) pixel_rate(319887360)
>>> [ 2.458995] gc8034 2-0037: could not get default pinstate
>>> [ 2.459003] gc8034 2-0037: could not get sleep pinstate
>>> [ 2.464279] gc8034 2-0037: gc8034 read reg:0xf0 failed !
>>> [ 2.464496] gc8034 2-0037: gc8034 read reg:0xf1 failed !
>>> [ 2.464510] gc8034 2-0037: Unexpected sensor id(000000), ret(-6)
>>> [ 2.465527] Loading compiled-in X.509 certificates
>>> [ 2.467269] pstore: Using crash dump compression: deflate
>>> [ 2.468329] rga: rga2, irq = 26, match scheduler
>>> [ 2.468814] rga: rga2 hardware loaded successfully,
>>> hw_version:3.2.63318.
>>> [ 2.468878] rga: rga2 probe successfully
>>> [ 2.469175] rga_iommu: IOMMU binding successfully, default mapping
>>> core[0x4]
>>> [ 2.469400] rga: Module initialized. v1.2.27
>>> [ 2.470498] mmc0: SDHCI controller on fe310000.sdhci
>>> [fe310000.sdhci] using ADMA
>>> [ 2.493542] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
>>> [ 2.495364] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
>>> [ 2.497144] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
>>> [ 2.500240] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
>>> [ 2.503917] mmc2: queuing unknown CIS tuple 0x81 (9 bytes)
>>> [ 2.504631] cfg80211: Loading compiled-in X.509 certificates for
>>> regulatory database
>>> [ 2.506492] cfg80211: Loaded X.509 cert 'sforshee:
>>> 00b28ddf47aef9cea7'
>>> [ 2.507370] platform regulatory.0: Direct firmware load for
>>> regulatory.db failed with error -2
>>> [ 2.507385] cfg80211: failed to load regulatory.db
>>> [ 2.507852] rockchip-pm rockchip-suspend: not set
>>> pwm-regulator-config
>>> [ 2.507873] rockchip-suspend not set sleep-mode-config for mem-lite
>>> [ 2.507882] rockchip-suspend not set wakeup-config for mem-lite
>>> [ 2.507890] rockchip-suspend not set sleep-mode-config for mem-ultra
>>> [ 2.507897] rockchip-suspend not set wakeup-config for mem-ultra
>>> [ 2.508944] I : [File] :
>>> drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 406;
>>> [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is
>>> '', rk_ko_ver is '5', built at '10:47:45', on 'Sep 8 2023'.
>>> [ 2.509481] Mali:
>>> [ 2.509485] Mali device driver loaded
>>> [ 2.509510] rkisp rkisp-vir0: clear unready subdev num: 1
>>> [ 2.510061] rkisp-vir0: update sensor failed
>>> [ 2.510089] ALSA device list:
>>> [ 2.510098] #0: rockchip,hdmi
>>> [ 2.515357] mmc0: Host Software Queue enabled
>>> [ 2.515405] mmc0: new HS200 MMC card at address 0001
>>> [ 2.516178] mmcblk0: mmc0:0001 SPeMMC 7.28 GiB
>>> [ 2.516462] mmcblk0boot0: mmc0:0001 SPeMMC partition 1 4.00 MiB
>>> [ 2.516865] mmcblk0boot1: mmc0:0001 SPeMMC partition 2 4.00 MiB
>>> [ 2.517172] mmcblk0rpmb: mmc0:0001 SPeMMC partition 3 4.00 MiB,
>>> chardev (237:0)
>>> [ 2.520599] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
>>> [ 2.523541] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
>>> [ 2.523576] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed!
>>> [ 2.523584] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET!
>>> [ 2.559579] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req
>>> 50000000Hz, actual 50000000HZ div = 0)
>>> [ 2.563120] mmc2: new high speed SDIO card at address 0001
>>> [ 2.565803] vendor storage:20190527 ret = 0
>>> [ 2.593649] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
>>> [ 2.593672] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed!
>>> [ 2.593681] <<GTP-ERR>>[gt1x_init:2345] Init failed, use default
>>> setting
>>> [ 2.593895] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6)
>>> [ 2.593908] <<GTP-ERR>>[gt1x_get_chip_type:895] I2c communication
>>> error.
>>> [ 2.593915] <<GTP-ERR>>[gt1x_init:2355] Get chip type failed!
>>> [ 2.594121] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6)
>>> [ 2.594133] <<GTP-ERR>>[gt1x_read_version:845] Read version failed!
>>> [ 2.700290] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6)
>>> [ 2.700310] <<GTP-ERR>>[gt1x_read_version:845] Read version failed!
>>> [ 2.806956] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6)
>>> [ 2.806976] <<GTP-ERR>>[gt1x_read_version:845] Read version failed!
>>> [ 2.913371] <<GTP-INF>>[gt1x_read_version:863] IC
>>> VERSION:GT_000000(Patch)_0000(Mask)_00(SensorID)
>>> [ 2.913392] <<GTP-INF>>[gt1x_init_panel:606] Config group0 used,
>>> length:239
>>> [ 2.913403] <<GTP-INF>>[gt1x_init_panel:657]
>>> X_MAX=4096,Y_MAX=4096,TRIGGER=0x01,WAKEUP_LEVEL=1
>>> [ 2.913623] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
>>> [ 2.913838] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
>>> [ 2.914056] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
>>> [ 2.914272] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
>>> [ 2.914488] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
>>> [ 2.914499] <<GTP-ERR>>[gt1x_send_cfg:551] Send config failed!
>>> [ 2.914507] <<GTP-ERR>>[gt1x_init:2367] Init panel failed.
>>> [ 2.914801] <<GTP-ERR>>[gt1x_ts_probe:587] GTP init failed!!!
>>> [ 2.914991] Goodix-TS-GT1X: probe of 1-0014 failed with error
>>> -2147483644
>>> [ 3.074494] EXT4-fs (mmcblk0p6): 2 orphan inodes deleted
>>> [ 3.074535] EXT4-fs (mmcblk0p6): recovery complete
>>> [ 3.078700] EXT4-fs (mmcblk0p6): mounted filesystem with ordered
>>> data mode. Opts: (null)
>>> [ 3.078794] VFS: Mounted root (ext4 filesystem) on device 179:6.
>>> [ 3.079676] devtmpfs: mounted
>>> [ 3.086768] Freeing unused kernel memory: 6592K
>>> [ 3.096802] Run /sbin/init as init process
>>> [ 3.096823] with arguments:
>>> [ 3.096827] /sbin/init
>>> [ 3.096830] with environment:
>>> [ 3.096833] HOME=/
>>> [ 3.096836] TERM=linux
>>> [ 3.096838] storagemedia=emmc
>>> [ 3.285409] systemd[1]: System time before build time, advancing
>>> clock.
>>> [ 3.290031] systemd[1]: Failed to look up module alias 'autofs4':
>>> Function not implemented
>>> [ 4.290576] systemd-journald[198]: Received client request to flush
>>> runtime journal.
>>> [ 4.297048] systemd-journald[198]: File
>>> /var/log/journal/91dd2456cbf54281afa309addad7e0db/system.journal
>>> corrupted or uncleanly shut down, renaming and replacing.
>>> [ 5.712823] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high!
>>> [ 5.763422] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host input!
>>> [ 5.763492] [BT_RFKILL]: ENABLE UART_RTS
>>> [ 5.870061] [BT_RFKILL]: DISABLE UART_RTS
>>> [ 5.870142] [BT_RFKILL]: bt turn on power
>>> [ 5.870175] [BT_RFKILL]: Request irq for bt wakeup host
>>> [ 5.870218] [BT_RFKILL]: ** disable irq
>>> [ 7.938573] EXT4-fs (mmcblk0p7): mounted filesystem with ordered
>>> data mode. Opts: (null)
>>> [ 8.001872] EXT4-fs (mmcblk0p8): mounted filesystem with ordered
>>> data mode. Opts: (null)
>>> [ 8.883246] [dhd] STATIC-MSG) dhd_static_buf_init : 101.10.361.18
>>> (wlan=r892223-20220519-1)
>>> [ 8.883702] [dhd] STATIC-MSG) dhd_init_wlan_mem : prealloc ok for
>>> index 0: 8131584(7941K)
>>> [ 9.450664] bcmdhd: loading out-of-tree module taints kernel.
>>> [ 9.464195] [dhd] _dhd_module_init: in Dongle Host Driver, version
>>> 101.10.361.25 (wlan=r892223-20220929-2)
>>>
>>> /home/gtc/geniatech/xpi-3566-zero/external/rkwifibt/drivers/bcmdhd
>>> compiled on Sep 25 2023 at 16:08:41
>>>
>>> [ 9.464339] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
>>> [ 9.464434] [dhd] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=74,
>>> oob_irq_flags=0x4
>>> [ 9.464447] [dhd] dhd_wlan_init_gpio: WL_REG_ON=-1
>>> [ 9.464455] [dhd] STATIC-MSG) dhd_static_buf_init : 101.10.361.25
>>> (wlan=r892223-20220928-2)
>>> [ 9.465021] [dhd] STATIC-MSG) dhd_init_wlan_mem : prealloc ok for
>>> index 0: 8138752(7948K)
>>> [ 9.465047] [dhd] dhd_wifi_platform_load: Enter
>>> [ 9.465056] [dhd] Power-up adapter 'DHD generic adapter'
>>> [ 9.465308] [dhd] dummy_probe: enter
>>> [ 9.469572] [dhd] dummy_probe: enter
>>> [ 9.475102] [dhd] wifi_platform_set_power = 1, delay: 200 msec
>>> [ 9.475135] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ========
>>> [ 9.475145] [WLAN_RFKILL]: rockchip_wifi_power: 1
>>> [ 9.475155] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
>>> [ 9.575560] file system registered
>>> [ 9.580048] [WLAN_RFKILL]: wifi turn on power [GPIO74-1]
>>> [ 9.797002] read descriptors
>>> [ 9.797132] read strings
>>> [ 9.887037] [dhd] wifi_platform_bus_enumerate device present 1
>>> [ 9.887086] [dhd] ======== Card detection to detect SDIO card!
>>> ========
>>> [ 9.903556] [dhd] bcmsdh_register: register client driver
>>> [ 9.910401] [dhd] bcmsdh_sdmmc_probe: Enter num=1
>>> [ 9.915945] [dhd] bcmsdh_sdmmc_probe: Enter num=2
>>> [ 9.915995] [dhd] bus num (host idx)=2, slot num (rca)=1
>>> [ 9.916006] [dhd] found adapter info 'DHD generic adapter'
>>> [ 9.916019] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 3,
>>> size 139264
>>> [ 9.916058] [dhd] succeed to alloc static buf
>>> [ 9.916066] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 4,
>>> size 0
>>> [ 9.916220] [dhd] sdioh_attach: set sd_f2_blocksize 256
>>> [ 9.916769] [dhd] sdioh_attach: sd clock rate = 50000000
>>> [ 9.922369] [dhd] dhdsdio_probe : no mutex held
>>> [ 9.922420] [dhd] dhdsdio_probe : set mutex lock
>>> [ 9.924390] [dhd] F1 signature read @0x18000000=0x15294345
>>> [ 9.931550] [dhd] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9
>>> pkg:0x2
>>> [ 9.932967] [dhd] DHD: dongle ram size is set to 819200(orig 819200)
>>> at 0x198000
>>> [ 9.933210] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 7,
>>> size 32600
>>> [ 9.933262] [dhd] dhd_conf_set_chiprev : devid=0xa9bf, chip=0x4345,
>>> chiprev=9
>>> [ 9.934698] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 0,
>>> size 10320
>>> [ 9.936446] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 5,
>>> size 65536
>>> [ 9.945095] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 19,
>>> size 65688
>>> [ 9.945253] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 20,
>>> size 262144
>>> [ 9.945335] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 22,
>>> size 65536
>>> [ 9.948104] [dhd] dhd_attach(): thread:dhd_watchdog_thread:3b8
>>> started
>>> [ 9.956868] [dhd] dhd_attach(): thread:dhd_dpc:3b9 started
>>> [ 9.960645] [dhd] dhd_attach(): thread:dhd_rxf:3bb started
>>> [ 9.960697] [dhd] dhd_deferred_work_init: work queue initialized
>>> [ 9.960711] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0
>>> -> mode 2
>>> [ 9.960719] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=10,
>>> TCPDATA_INFO_MAXNUM=10
>>> [ 9.960784] [dhd] sdioh_cis_read: func_cis_ptr[0]=0x10ac
>>> [ 9.975873] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 1,
>>> size 10300
>>> [ 9.975925] [dhd] STATIC-MSG) dhd_wlan_mem_prealloc : section 2,
>>> size 65536
>>> [ 9.976080] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN
>>> [ 9.976283] [dhd] Dongle Host Driver, version 101.10.361.25
>>> (wlan=r892223-20220929-2)
>>>
>>> /home/gtc/geniatech/xpi-3566-zero/external/rkwifibt/drivers/bcmdhd
>>> compiled on Sep 25 2023 at 16:08:41
>>>
>>> [ 9.983502] [dhd] Register interface [wlan0] MAC: b8:2d:xxxxxx
>>>
>>> [ 9.984030] [dhd] [wlan0] wl_android_wifi_off : in g_wifi_on=1,
>>> on_failure=1
>>> [ 9.984062] [dhd] dhd_bus_devreset: == Power OFF ==
>>> [ 9.985260] [dhd] dhd_bus_stop: making DHD_BUS_DOWN
>>> [ 9.985333] [dhd] bcmsdh_oob_intr_unregister: Enter
>>> [ 9.985343] [dhd] bcmsdh_oob_intr_unregister: irq is not registered
>>> [ 9.985361] [dhd] dhd_bus_devreset: making dhdpub up FALSE
>>> [ 9.985371] [dhd] dhd_txglom_enable: enable 0
>>> [ 9.985380] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
>>> [ 9.985522] [dhd] wifi_platform_set_power = 0, delay: 0 msec
>>> [ 9.985536] [dhd] ======== PULL WL_REG_ON(-1) LOW! ========
>>> [ 9.985545] [WLAN_RFKILL]: rockchip_wifi_power: 0
>>> [ 9.985554] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
>>> [ 9.985561] wifi power off
>>> [ 10.051825] [dhd] dhd_pri_open : probe is already running! return.
>>> [ 10.074460] [dhd] dhd_pri_open : probe is already running! return.
>>> [ 10.084465] [dhd] dhd_pri_open : probe is already running! return.
>>> [ 10.090137] [WLAN_RFKILL]: wifi shut off power [GPIO74-0]
>>> [ 10.090186] [dhd] [wlan0] wl_android_wifi_off : out
>>> [ 10.090201] [dhd] dhdsdio_probe : mutex is released.
>>> [ 10.090516] [dhd] _dhd_module_init: Exit err=0
>>> [ 10.164305] [BT_RFKILL]: bt shut off power
>>> [ 10.203877] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high!
>>> [ 10.256770] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host input!
>>> [ 10.256850] [BT_RFKILL]: ENABLE UART_RTS
>>> [ 10.363488] [BT_RFKILL]: DISABLE UART_RTS
>>> [ 10.363579] [BT_RFKILL]: bt turn on power
>>> [ 10.363613] [BT_RFKILL]: Request irq for bt wakeup host
>>> [ 10.363658] [BT_RFKILL]: ** disable irq
>>> [ 10.406005] of_dma_request_slave_channel: dma-names property of node
>>> '/serial@fe650000' missing or empty
>>> [ 10.408347] dw-apb-uart fe650000.serial: failed to request DMA, use
>>> interrupt mode
>>> [ 10.483792] [BT_RFKILL]: bt shut off power
>>> [ 11.533061] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host high!
>>> [ 11.583473] [BT_RFKILL]: rfkill_rk_set_power: set bt wake_host input!
>>> [ 11.583551] [BT_RFKILL]: ENABLE UART_RTS
>>> [ 11.690085] [BT_RFKILL]: DISABLE UART_RTS
>>> [ 11.690169] [BT_RFKILL]: bt turn on power
>>> [ 11.690203] [BT_RFKILL]: Request irq for bt wakeup host
>>> [ 11.690245] [BT_RFKILL]: ** disable irq
>>> [ 13.920568] systemd-journald[198]: File
>>> /var/log/journal/91dd2456cbf54281afa309addad7e0db/user-1000.journal
>>> corrupted or uncleanly shut down, renaming and replacing.
>>> [ 14.000271] Freeing drm_logo memory: 736K
>>> [ 15.527834] ttyFIQ ttyFIQ0: tty_port_close_start: tty->count = 1
>>> port count = 2
>>> [ 20.401475] [dhd] dhd_pri_open : no mutex held
>>> [ 20.401613] [dhd] dhd_pri_open : set mutex lock
>>> [ 20.401625] [dhd] [wlan0] dhd_open : Enter
>>> [ 20.401635] [dhd] Dongle Host Driver, version 101.10.361.25
>>> (wlan=r892223-20220929-2)
>>>
>>> /home/gtc/geniatech/xpi-3566-zero/external/rkwifibt/drivers/bcmdhd
>>> compiled on Sep 25 2023 at 16:08:41
>>>
>>> [ 20.401651] [dhd] dhd_open: ######### called for ifidx=0 #########
>>> [ 20.401669] [dhd] [wlan0] wl_android_wifi_on : in g_wifi_on=0
>>> [ 20.401679] [dhd] wifi_platform_set_power = 1, delay: 200 msec
>>> [ 20.401686] [dhd] ======== PULL WL_REG_ON(-1) HIGH! ========
>>> [ 20.401694] [WLAN_RFKILL]: rockchip_wifi_power: 1
>>> [ 20.401703] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
>>> [ 20.506800] [WLAN_RFKILL]: wifi turn on power [GPIO74-1]
>>> [ 20.813369] [dhd] sdio_sw_reset: call mmc_hw_reset
>>> [ 20.826812] mmc_host mmc2: Bus speed (slot 0) = 375000Hz (slot req
>>> 400000Hz, actual 375000HZ div = 0)
>>> [ 20.857057] mmc2: queuing unknown CIS tuple 0x80 (2 bytes)
>>> [ 20.858825] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
>>> [ 20.860532] mmc2: queuing unknown CIS tuple 0x80 (3 bytes)
>>> [ 20.863836] mmc2: queuing unknown CIS tuple 0x80 (7 bytes)
>>> [ 20.867573] mmc2: queuing unknown CIS tuple 0x81 (9 bytes)
>>> [ 20.925517] mmc_host mmc2: Bus speed (slot 0) = 50000000Hz (slot req
>>> 50000000Hz, actual 50000000HZ div = 0)
>>> [ 20.925667] [dhd] sdioh_start: set sd_f2_blocksize 256
>>> [ 20.925981] [dhd] dhd_bus_devreset: == Power ON ==
>>> [ 20.926104] [dhd] F1 signature read @0x18000000=0x15294345
>>> [ 20.929772] [dhd] F1 signature OK, socitype:0x1 chip:0x4345 rev:0x9
>>> pkg:0x2
>>> [ 20.930521] [dhd] DHD: dongle ram size is set to 819200(orig 819200)
>>> at 0x198000
>>> [ 20.930587] [dhd] dhd_bus_devreset: making DHD_BUS_DOWN
>>> [ 20.930648] [dhd] dhdsdio_probe_init: making DHD_BUS_DOWN
>>> [ 20.930825] [dhd] dhd_conf_set_path_params : Final
>>> fw_path=/vendor/etc/firmware/fw_bcm43456c5_ag.bin
>>> [ 20.930835] [dhd] dhd_conf_set_path_params : Final
>>> nv_path=/vendor/etc/firmware/nvram_ap6256.txt
>>> [ 20.930843] [dhd] dhd_conf_set_path_params : Final
>>> clm_path=/vendor/etc/firmware/clm_bcm43456c5_ag.blob
>>> [ 20.930850] [dhd] dhd_conf_set_path_params : Final
>>> conf_path=/vendor/etc/firmware/config.txt
>>> [ 20.931076] [dhd] dhd_os_open_image1:
>>> /vendor/etc/firmware/config.txt (240 bytes) open success
>>> [ 20.931522] [dhd] dhd_conf_read_pm_params : PM = 0
>>> [ 20.931539] [dhd] dhd_conf_read_pm_params : pm_in_suspend = 2
>>> [ 20.931560] [dhd] dhd_conf_read_others : keep_alive_period = 120000
>>> [ 20.931573] [dhd] dhd_conf_read_others : garp = 1
>>> [ 20.931585] [dhd] dhd_conf_read_pm_params : suspend_bcn_li_dtim = 10
>>> [ 20.931601] [dhd] dhd_conf_read_others : wl_preinit =
>>> pm2_sleep_ret=20
>>> [ 20.931614] [dhd] dhd_conf_read_pkt_filter : pkt_filter_del id = 100
>>> 102 103 104 105 107
>>> [ 20.931641] [dhd] dhd_conf_read_pkt_filter : pkt_filter_add[0][] =
>>> 142 0 0 77 0xffffffffffffffffffffffffffffff
>>> 0x2F6465766963652F77616B6575702F
>>> [ 20.932260] [dhd] dhd_os_open_image1:
>>> /vendor/etc/firmware/fw_bcm43456c5_ag.bin (508373 bytes) open success
>>> [ 21.012945] [dhd] dhd_os_open_image1:
>>> /vendor/etc/firmware/nvram_ap6256.txt (2424 bytes) open success
>>> [ 21.013594] [dhd] #AP6256_NVRAM_V1.2_09202018.txt
>>> [ 21.014325] [dhd] dhdsdio_write_vars: Download, Upload and compare
>>> of NVRAM succeeded.
>>> [ 21.093111] [dhd] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
>>> [ 21.094157] [dhd] bcmsdh_oob_intr_register: HW_OOB irq=74 flags=0x4
>>> [ 21.096264] [dhd] wlc_ver_major 3, wlc_ver_minor 0
>>> [ 21.097448] [dhd] dhd_preinit_ioctls: preinit_status IOVAR not
>>> supported, use legacy preinit
>>> [ 21.097495] [dhd] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2
>>> -> mode 1
>>> [ 21.097505] [dhd] dhd_tcpack_suppress_set: TCPACK_INFO_MAXNUM=10,
>>> TCPDATA_INFO_MAXNUM=10
>>> [ 21.098671] [dhd] dhd_legacy_preinit_ioctls: use firmware generated
>>> mac_address b8:2d:xxxxx
>>> [ 21.098774] [dhd] dhd_apply_default_clm: Ignore clm file
>>> /vendor/etc/firmware/clm_bcm43456c5_ag.blob
>>> [ 21.101446] [dhd] Firmware up: op_mode=0x0005, MAC=b8:2d:xxxxx
>>> [ 21.107634] [dhd] dhd_legacy_preinit_ioctls: event_log_max_sets: 31
>>> ret: -23
>>> [ 21.110968] [dhd] arp_enable:1 arp_ol:0
>>> [ 21.111012] [dhd] dhd_conf_add_pkt_filter : 142 0 0 77
>>> 0xffffffffffffffffffffffffffffff 0x2F6465766963652F77616B6575702F
>>> [ 21.117056] [dhd] Driver: 101.10.361.25 (wlan=r892223-20220929-2)
>>> [dhd] Firmware: wl0: Sep 7 2018 14:33:37 version
>>> 7.45.96.27 (42b546f@shgit) (r) FWID 01-c958c084 es7.c5.n4.a3
>>> [dhd] CLM: 9.2.9 (2016-02-03 04:34:31)
>>> [ 21.117574] [dhd] dhd_txglom_enable: enable 1
>>> [ 21.117622] [dhd] dhd_conf_set_txglom_params : txglom_mode=copy
>>> [ 21.117633] [dhd] dhd_conf_set_txglom_params : txglomsize=36,
>>> deferred_tx_len=0
>>> [ 21.117640] [dhd] dhd_conf_set_txglom_params : txinrx_thres=128,
>>> dhd_txminmax=-1
>>> [ 21.117648] [dhd] dhd_conf_set_txglom_params : tx_max_offset=0,
>>> txctl_tmo_fix=300
>>> [ 21.117661] [dhd] dhd_conf_get_disable_proptx : fw_proptx=1,
>>> disable_proptx=-1
>>> [ 21.119224] [dhd] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv
>>> signaling, 64
>>> [ 21.122689] [dhd] dhd_pno_init: Support Android Location Service
>>> [ 21.148163] [dhd] dhd_legacy_preinit_ioctls: Failed to get preserve
>>> log # !
>>> [ 21.169492] [dhd] dhd_conf_map_country_list : CN/38
>>> [ 21.169543] [dhd] dhd_conf_set_country : set country CN, revision 38
>>> [ 21.172072] [dhd] CFG80211-ERROR) wl_cfg80211_event : Event handler
>>> is not created (WLC_E_COUNTRY_CODE_CHANGED)
>>> [ 21.172409] [dhd] dhd_conf_set_country : Country code: CN (CN/38)
>>> [ 21.179949] [dhd] [wlan0] wl_android_wifi_on : Success
>>> [ 21.233299] [dhd] CFG80211-ERROR) init_roam_cache : roamscan_mode
>>> iovar failed. -23
>>> [ 21.233369] [dhd] CFG80211-ERROR) wl_cfg80211_up : Failed to enable
>>> RCC.
>>> [ 21.234407] [dhd] [wlan0] dhd_open : Exit ret=0
>>> [ 21.234429] [dhd] [wlan0] dhd_pri_open : tx queue started
>>> [ 21.234437] [dhd] dhd_pri_open : mutex is released.
>>> [ 21.301397] [dhd] P2P interface registered
>>> [ 21.331052] [dhd] WLC_E_IF: NO_IF set, event Ignored
>>>
>>> [ 21.332373] [dhd] P2P interface started
>>> [ 21.394531] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 0,
>>> bssidx: 0
>>> [ 25.399791] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 1,
>>> bssidx: 0
>>> [ 25.896769] usb 1-1: new full-speed USB device number 2 using
>>> xhci-hcd
>>> [ 26.040641] usb 1-1: New USB device found, idVendor=046d,
>>> idProduct=c52b, bcdDevice=24.11
>>> [ 26.040703] usb 1-1: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=0
>>> [ 26.040714] usb 1-1: Product: USB Receiver
>>> [ 26.040723] usb 1-1: Manufacturer: Logitech
>>> [ 26.078789] input: Logitech USB Receiver as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1:1.0/0003:046D:C52B.0001/input/input1
>>> [ 26.134907] hid-generic 0003:046D:C52B.0001: input,hidraw0: USB HID
>>> v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1/input0
>>> [ 26.150920] input: Logitech USB Receiver Mouse as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1:1.1/0003:046D:C52B.0002/input/input2
>>> [ 26.151935] input: Logitech USB Receiver Consumer Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1:1.1/0003:046D:C52B.0002/input/input3
>>> [ 26.207483] input: Logitech USB Receiver System Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1:1.1/0003:046D:C52B.0002/input/input4
>>> [ 26.208529] hid-generic 0003:046D:C52B.0002: input,hiddev96,hidraw1:
>>> USB HID v1.11 Mouse [Logitech USB Receiver] on
>>> usb-xhci-hcd.4.auto-1/input1
>>> [ 26.222063] hid-generic 0003:046D:C52B.0003: hiddev97,hidraw2: USB
>>> HID v1.11 Device [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1/input2
>>> [ 30.397602] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 2,
>>> bssidx: 0
>>> [ 33.440143] vcc3v3_lcd1_n: disabling
>>> [ 37.403274] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 3,
>>> bssidx: 0
>>> [ 40.444368] usb 1-1: USB disconnect, device number 2
>>> [ 47.400586] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 4,
>>> bssidx: 0
>>> [ 57.310046] usb 1-1: new high-speed USB device number 3 using
>>> xhci-hcd
>>> [ 57.450395] usb 1-1: New USB device found, idVendor=1a40,
>>> idProduct=0101, bcdDevice= 1.00
>>> [ 57.450437] usb 1-1: New USB device strings: Mfr=0, Product=1,
>>> SerialNumber=0
>>> [ 57.450448] usb 1-1: Product: USB2.0 HUB
>>> [ 57.492389] hub 1-1:1.0: USB hub found
>>> [ 57.492541] hub 1-1:1.0: 4 ports detected
>>> [ 57.870058] usb 1-1.1: new full-speed USB device number 4 using
>>> xhci-hcd
>>> [ 58.063782] usb 1-1.1: New USB device found, idVendor=046d,
>>> idProduct=c52b, bcdDevice=24.11
>>> [ 58.063821] usb 1-1.1: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=0
>>> [ 58.063831] usb 1-1.1: Product: USB Receiver
>>> [ 58.063839] usb 1-1.1: Manufacturer: Logitech
>>> [ 58.168459] input: Logitech USB Receiver as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C52B.0004/input/input6
>>> [ 58.224158] hid-generic 0003:046D:C52B.0004: input,hidraw0: USB HID
>>> v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1.1/input0
>>> [ 58.235027] input: Logitech USB Receiver Mouse as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0005/input/input7
>>> [ 58.235451] input: Logitech USB Receiver Consumer Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0005/input/input8
>>> [ 58.290565] input: Logitech USB Receiver System Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0005/input/input9
>>> [ 58.291040] hid-generic 0003:046D:C52B.0005: input,hiddev96,hidraw1:
>>> USB HID v1.11 Mouse [Logitech USB Receiver] on
>>> usb-xhci-hcd.4.auto-1.1/input1
>>> [ 58.302615] hid-generic 0003:046D:C52B.0006: hiddev97,hidraw2: USB
>>> HID v1.11 Device [Logitech USB Receiver] on
>>> usb-xhci-hcd.4.auto-1.1/input2
>>> [ 61.410435] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 5,
>>> bssidx: 0
>>> [ 62.260152] usb 1-1.1: USB disconnect, device number 4
>>> [ 62.733334] usb 1-1.1: new full-speed USB device number 5 using
>>> xhci-hcd
>>> [ 62.926727] usb 1-1.1: New USB device found, idVendor=046d,
>>> idProduct=c52b, bcdDevice=24.11
>>> [ 62.926764] usb 1-1.1: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=0
>>> [ 62.926774] usb 1-1.1: Product: USB Receiver
>>> [ 62.926782] usb 1-1.1: Manufacturer: Logitech
>>> [ 63.032694] input: Logitech USB Receiver as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C52B.0007/input/input11
>>> [ 63.088204] hid-generic 0003:046D:C52B.0007: input,hidraw0: USB HID
>>> v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1.1/input0
>>> [ 63.094013] input: Logitech USB Receiver Mouse as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0008/input/input12
>>> [ 63.094541] input: Logitech USB Receiver Consumer Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0008/input/input13
>>> [ 63.150590] input: Logitech USB Receiver System Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0008/input/input14
>>> [ 63.151342] hid-generic 0003:046D:C52B.0008: input,hiddev96,hidraw1:
>>> USB HID v1.11 Mouse [Logitech USB Receiver] on
>>> usb-xhci-hcd.4.auto-1.1/input1
>>> [ 63.156209] hid-generic 0003:046D:C52B.0009: hiddev97,hidraw2: USB
>>> HID v1.11 Device [Logitech USB Receiver] on
>>> usb-xhci-hcd.4.auto-1.1/input2
>>> [ 63.466730] usb 1-1.4: new low-speed USB device number 6 using
>>> xhci-hcd
>>> [ 63.662293] usb 1-1.4: New USB device found, idVendor=046d,
>>> idProduct=c31c, bcdDevice=64.02
>>> [ 63.662330] usb 1-1.4: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=0
>>> [ 63.662340] usb 1-1.4: Product: USB Keyboard
>>> [ 63.662349] usb 1-1.4: Manufacturer: Logitech
>>> [ 63.738680] input: Logitech USB Keyboard as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.0/0003:046D:C31C.000A/input/input16
>>> [ 63.794431] hid-generic 0003:046D:C31C.000A: input,hidraw3: USB HID
>>> v1.10 Keyboard [Logitech USB Keyboard] on usb-xhci-hcd.4.auto-1.4/input0
>>> [ 63.802956] input: Logitech USB Keyboard Consumer Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.000B/input/input17
>>> [ 63.857239] input: Logitech USB Keyboard System Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.000B/input/input18
>>> [ 63.858002] hid-generic 0003:046D:C31C.000B: input,hiddev98,hidraw4:
>>> USB HID v1.10 Device [Logitech USB Keyboard] on
>>> usb-xhci-hcd.4.auto-1.4/input1
>>> [ 81.401443] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 6,
>>> bssidx: 0
>>> [ 100.148159] usb 1-1.4: USB disconnect, device number 6
>>> [ 104.500151] usb 1-1.1: USB disconnect, device number 5
>>> [ 105.000040] usb 1-1.1: new full-speed USB device number 7 using
>>> xhci-hcd
>>> [ 105.176859] usb 1-1.1: Device not responding to setup address.
>>> [ 105.383527] usb 1-1.1: Device not responding to setup address.
>>> [ 105.590046] usb 1-1.1: device not accepting address 7, error -71
>>> [ 105.970048] usb 1-1.1: new full-speed USB device number 8 using
>>> xhci-hcd
>>> [ 106.163750] usb 1-1.1: New USB device found, idVendor=046d,
>>> idProduct=c52b, bcdDevice=24.11
>>> [ 106.163789] usb 1-1.1: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=0
>>> [ 106.163799] usb 1-1.1: Product: USB Receiver
>>> [ 106.163808] usb 1-1.1: Manufacturer: Logitech
>>> [ 106.296734] input: Logitech USB Receiver as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C52B.000C/input/input19
>>> [ 106.354122] hid-generic 0003:046D:C52B.000C: input,hidraw0: USB HID
>>> v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1.1/input0
>>> [ 106.359457] input: Logitech USB Receiver Mouse as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.000D/input/input20
>>> [ 106.359906] input: Logitech USB Receiver Consumer Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.000D/input/input21
>>> [ 106.413872] input: Logitech USB Receiver System Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.000D/input/input22
>>> [ 106.414454] hid-generic 0003:046D:C52B.000D: input,hiddev96,hidraw1:
>>> USB HID v1.11 Mouse [Logitech USB Receiver] on
>>> usb-xhci-hcd.4.auto-1.1/input1
>>> [ 106.418857] hid-generic 0003:046D:C52B.000E: hiddev97,hidraw2: USB
>>> HID v1.11 Device [Logitech USB Receiver] on
>>> usb-xhci-hcd.4.auto-1.1/input2
>>> [ 106.729981] usb 1-1.4: new low-speed USB device number 9 using
>>> xhci-hcd
>>> [ 106.925618] usb 1-1.4: New USB device found, idVendor=046d,
>>> idProduct=c31c, bcdDevice=64.02
>>> [ 106.925655] usb 1-1.4: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=0
>>> [ 106.925665] usb 1-1.4: Product: USB Keyboard
>>> [ 106.925673] usb 1-1.4: Manufacturer: Logitech
>>> [ 107.002451] input: Logitech USB Keyboard as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.0/0003:046D:C31C.000F/input/input24
>>> [ 107.057502] hid-generic 0003:046D:C31C.000F: input,hidraw3: USB HID
>>> v1.10 Keyboard [Logitech USB Keyboard] on usb-xhci-hcd.4.auto-1.4/input0
>>> [ 107.065863] input: Logitech USB Keyboard Consumer Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.0010/input/input25
>>> [ 107.120485] input: Logitech USB Keyboard System Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.0010/input/input26
>>> [ 107.121039] hid-generic 0003:046D:C31C.0010: input,hiddev98,hidraw4:
>>> USB HID v1.10 Device [Logitech USB Keyboard] on
>>> usb-xhci-hcd.4.auto-1.4/input1
>>> [ 110.423651] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 7,
>>> bssidx: 0
>>> [ 153.400865] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 8,
>>> bssidx: 0
>>> [ 217.401022] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 9,
>>> bssidx: 0
>>> [ 230.082903] rockchip-vop2 fe040000.vop:
>>> [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
>>> [ 230.116490] [drm:vop2_plane_atomic_check] *ERROR* Cluster0-win0 is
>>> invisible(src: pos[0, 0] rect[64 x 64] dst: pos[1583, 1598] rect[64 x
>>> 64]
>>> [ 230.187909] rockchip-vop2 fe040000.vop:
>>> [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p120, type:
>>> 11(if:800, flag:0x0) for vp0 dclk: 297000000
>>> [ 246.747224] rockchip-vop2 fe040000.vop:
>>> [drm:vop2_crtc_atomic_disable] Crtc atomic disable vp0
>>> [ 246.763535] rockchip-vop2 fe040000.vop:
>>> [drm:vop2_crtc_atomic_enable] Update mode to 1920x1080p60, type:
>>> 11(if:800, flag:0x0) for vp0 dclk: 148500000
>>> [ 312.402381] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 10,
>>> bssidx: 0
>>> [ 412.212143] usb 1-1.1: USB disconnect, device number 8
>>> [ 412.570255] usb 1-1.4: USB disconnect, device number 9
>>> [ 413.063258] usb 1-1.4: new low-speed USB device number 10 using
>>> xhci-hcd
>>> [ 413.258781] usb 1-1.4: New USB device found, idVendor=046d,
>>> idProduct=c31c, bcdDevice=64.02
>>> [ 413.258816] usb 1-1.4: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=0
>>> [ 413.258825] usb 1-1.4: Product: USB Keyboard
>>> [ 413.258833] usb 1-1.4: Manufacturer: Logitech
>>> [ 413.338520] input: Logitech USB Keyboard as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.0/0003:046D:C31C.0011/input/input27
>>> [ 413.394022] hid-generic 0003:046D:C31C.0011: input,hidraw0: USB HID
>>> v1.10 Keyboard [Logitech USB Keyboard] on usb-xhci-hcd.4.auto-1.4/input0
>>> [ 413.402397] input: Logitech USB Keyboard Consumer Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.0012/input/input28
>>> [ 413.457068] input: Logitech USB Keyboard System Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.4/1-1.4:1.1/0003:046D:C31C.0012/input/input29
>>> [ 413.457645] hid-generic 0003:046D:C31C.0012: input,hiddev96,hidraw1:
>>> USB HID v1.10 Device [Logitech USB Keyboard] on
>>> usb-xhci-hcd.4.auto-1.4/input1
>>> [ 415.589983] usb 1-1.2: new high-speed USB device number 11 using
>>> xhci-hcd
>>> [ 415.781101] usb 1-1.2: New USB device found, idVendor=0781,
>>> idProduct=5583, bcdDevice= 1.00
>>> [ 415.781138] usb 1-1.2: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=3
>>> [ 415.781149] usb 1-1.2: Product: SanDisk 3.2Gen1
>>> [ 415.781157] usb 1-1.2: Manufacturer: USB
>>> [ 415.781166] usb 1-1.2: SerialNumber:
>>> 05016efe255b095ca37d7cfd7cae5eeabf2a28f4e4e9fd61b8aa8177cbd545deddd80000000000000000000088e142f0ff190a10835581075e2a041c
>>> [ 415.782270] usb-storage 1-1.2:1.0: USB Mass Storage device detected
>>> [ 415.783069] scsi host0: usb-storage 1-1.2:1.0
>>> [ 416.801089] scsi 0:0:0:0: Direct-Access USB SanDisk
>>> 3.2Gen1 1.00 PQ: 0 ANSI: 6
>>> [ 416.802789] sd 0:0:0:0: [sda] 60088320 512-byte logical blocks:
>>> (30.8 GB/28.7 GiB)
>>> [ 416.803281] sd 0:0:0:0: [sda] Write Protect is off
>>> [ 416.803302] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
>>> [ 416.805948] sd 0:0:0:0: [sda] Write cache: disabled, read cache:
>>> enabled, doesn't support DPO or FUA
>>> [ 416.883060] sda: sda1 sda4
>>> [ 416.886113] sd 0:0:0:0: [sda] Attached SCSI removable disk
>>> [ 433.498482] [dhd] [wlan0] wl_run_escan : LEGACY_SCAN sync ID: 11,
>>> bssidx: 0
>>> [ 443.700195] usb 1-1.2: USB disconnect, device number 11
>>> [ 452.709967] usb 1-1.1: new full-speed USB device number 12 using
>>> xhci-hcd
>>> [ 452.903722] usb 1-1.1: New USB device found, idVendor=046d,
>>> idProduct=c52b, bcdDevice=24.11
>>> [ 452.903759] usb 1-1.1: New USB device strings: Mfr=1, Product=2,
>>> SerialNumber=0
>>> [ 452.903768] usb 1-1.1: Product: USB Receiver
>>> [ 452.903776] usb 1-1.1: Manufacturer: Logitech
>>> [ 453.016266] input: Logitech USB Receiver as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.0/0003:046D:C52B.0013/input/input30
>>> [ 453.070710] hid-generic 0003:046D:C52B.0013: input,hidraw2: USB HID
>>> v1.11 Keyboard [Logitech USB Receiver] on usb-xhci-hcd.4.auto-1.1/input0
>>> [ 453.075931] input: Logitech USB Receiver Mouse as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0014/input/input31
>>> [ 453.076342] input: Logitech USB Receiver Consumer Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0014/input/input32
>>> [ 453.133765] input: Logitech USB Receiver System Control as
>>> /devices/platform/usbhost/fd000000.dwc3/xhci-hcd.4.auto/usb1/1-1/1-1.1/1-1.1:1.1/0003:046D:C52B.0014/input/input33
>>> [ 453.134201] hid-generic 0003:046D:C52B.0014: input,hiddev97,hidraw3:
>>> USB HID v1.11 Mouse [Logitech USB Receiver] on
>>> usb-xhci-hcd.4.auto-1.1/input1
>>> [ 453.138582] hid-generic 0003:046D:C52B.0015: hiddev98,hidraw4: USB
>>> HID v1.11 Device [Logitech USB Receiver] on
>>> usb-xhci-hcd.4.auto-1.1/input2
>>>
>>>
>>> --Z--
>>
>> --
>> --Z--
>
> --
> --Z--
--
--Z--
