Hi Stig, >When I install another Sangoma card on the same system (pri_net), and >connect the two cards with a PRI cross-over cable both cards get connected >(green led) and Asterisk reports both spans: >Status: Provisioned, UP, Active
It does look your installation is fine, i.e you are being able to send/receive packets. One way to confirm this is to perform a trace on span 1: (with the E1 cross-over cable between the two ports) 1. In the Asterisk CLI, type: pri intense debug span 1. You should see that packets are being transmitted in both directions, i.e. Some packets will have > > > On the left hand side and others will have < < < 2. In another command window (linux bash), type: Wanpipemon -I w1g1 -c trd This is a sangoma tool that will trace the d-channel of span 1. Check if you are having both incoming and outgoing packets. If for both tests, you are receiving and transmitting packets, this means your connection is fine, but your telco line is not provisioned yet. Contact your telco and tell them that you are not receiving packets. If you are receiving and transmitting packets from the wanpipemon trace, but only transmitting or only receiving in the asterisk CLI, then this that the Sangoma card is not interfacing properly with zaptel. This usually happens because you did not re-compile zaptel after installing wanpipe. Please re-compile zaptel. The correct installation sequence is: 1. Zaptel, Libpri, Asterisk 2. wanpipe 3. recompile zaptel. 4. perform configurations (wancfg, zaptel.conf etc.. ) Do not hesitate to contact me if you have any questions. Regards, David Yat Sin Sangoma Technologies (905) 474-1990 x119 (800) 388-2475 x119 Fax: (905) 474 9223 MSN: [EMAIL PROTECTED] Email: [EMAIL PROTECTED] Website: www.sangoma.com -----Original Message----- From: Stig Even Larsen [mailto:[EMAIL PROTECTED] Sent: November 25, 2005 3:21 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] Sangoma problems!? I'm having problems connecting my Sangoma cards to our PRI (E1) interface. It seems that the card get connected (green led), but Asterisk reports: Status: Provisioned, Down, Active. When I install another Sangoma card on the same system (pri_net), and connect the two cards with a PRI cross-over cable both cards get connected (green led) and Asterisk reports both spans: Status: Provisioned, UP, Active What could be wrong? I'm I missing something? zaptel.conf ;Telco PRI span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 ;PBX span=2,0,0,ccs,hdb3,crc4,yellow bchan=32-46,48-62 dchan=47 zapata.conf (minimal) [channels] context = from-pstn switchtype = euroisdn group=0 signalling = pri_cpe channel => 1-15 channel => 17-31 context = alcatel switchtype = euroisdn group=1 signalling = pri_net channel => 32-46 channel => 48-62 Best regards, Stig Even Larsen David Yat Sin Sangoma Technologies (905) 474-1990 x119 (800) 388-2475 x119 Fax: (905) 474 9223 MSN: [EMAIL PROTECTED] Email: [EMAIL PROTECTED] Website: www.sangoma.com -----Original Message----- From: Stig Even Larsen [mailto:[EMAIL PROTECTED] Sent: November 25, 2005 3:21 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] Sangoma problems!? I'm having problems connecting my Sangoma cards to our PRI (E1) interface. It seems that the card get connected (green led), but Asterisk reports: Status: Provisioned, Down, Active. When I install another Sangoma card on the same system (pri_net), and connect the two cards with a PRI cross-over cable both cards get connected (green led) and Asterisk reports both spans: Status: Provisioned, UP, Active What could be wrong? I'm I missing something? zaptel.conf ;Telco PRI span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 ;PBX span=2,0,0,ccs,hdb3,crc4,yellow bchan=32-46,48-62 dchan=47 zapata.conf (minimal) [channels] context = from-pstn switchtype = euroisdn group=0 signalling = pri_cpe channel => 1-15 channel => 17-31 context = alcatel switchtype = euroisdn group=1 signalling = pri_net channel => 32-46 channel => 48-62 Best regards, Stig Even Larsen _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users