I know and it's crazy isn't it because this is what i have in my zaptel.conf
bchan=1-15 bchan=17-31 dchan=16 span=1,1,0,ccs,hdb3,crc4 loadzone=sg defaultzone=sg The configuration is set to conform to my ISDN30 E1 specifications. And the jumper on the digium card is closed to enable E1 mode. What have I done wrong here guys.. I can't get it.. --- "Eric \"ManxPower\" Wieling" <[EMAIL PROTECTED]> wrote: > ESF/B8ZS is a T-1 config. > > azyuky wrote: > > Hi Josue and list, > > > > This is part of my dmesg log. Also one other thing, I don't know why the red > light > > on span/port 1 of my card keep flashing.. is it normal that way? Or it's > supposed to > > mean something? Obviously I have no experience with ISDN before so this is > > my > very > > first try. > > > > Found TE2XXP at base address e7001000, remapped to e001a000 > > TE2XXP version c01a0164, burst OFF, slip debug: OFF > > FALC version: 00000005, Board ID: 00 > > Reg 0: 0x1e6ab400 > > Reg 1: 0x1e6ab000 > > Reg 2: 0xffffffff > > Reg 3: 0x00000000 > > Reg 4: 0x00000000 > > Reg 5: 0x00000000 > > Reg 6: 0xc01a0164 > > Reg 7: 0x00001000 > > Reg 8: 0x00000000 > > Reg 9: 0x00ff0000 > > Reg 10: 0x00000000 > > TE2XXP: Launching card: 0 > > TE2XXP: Setting up global serial parameters > > Found a Wildcard: Wildcard TE205P > > About to enter spanconfig! > > Done with spanconfig! > > Registered tone zone > > About to enter startup! > > TE2XXP: Span 1 configured for ESF/B8ZS > > wct2xxp: Setting yellow alarm on span 1 > > 2G: Got interrupt, status = 0000000d, GIS = 0081 > > SPAN 1: Primary Sync Source > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > VPM: Not Present > > Completed startup! > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > 2G: Got interrupt, status = 0000000a, GIS = 0080 > > About to enter spanconfig! > > About to enter startup! > > TE2XXP: Span 1 configured for ESF/B8ZS > > SPAN 1: Primary Sync Source > > Completed startup! > > Registered tone zone > > About to enter spanconfig! > > About to enter startup! > > TE2XXP: Span 1 configured for ESF/B8ZS > > SPAN 1: Primary Sync Source > > Completed startup! > > Registered tone zone > > About to enter spanconfig! > > About to enter startup! > > TE2XXP: Span 1 configured for ESF/B8ZS > > SPAN 1: Primary Sync Source > > Completed startup! > > Registered tone zone > > > > > > --- Josué Conti <[EMAIL PROTECTED]> wrote: > > > >> Hi, test with dmesg and past in list the log´s > >> > >> Regards > >> > >> Josué > >> > >> 2006/5/10, azyuky <[EMAIL PROTECTED]>: > >>> Hi guys, > >>> > >>> Currently I just purchased the TE205P for the installation of my ISDN30 > >>> setup. I > >>> compiled, setup the card correctly I think. When I do the ztcfg -vvv it > >>> shows all 31 > >>> channels clear, with 30 bchannels using for voice ranging from 1-15, > >>> 17-31, and 16 > >>> is the dchannel. However, when I do a cat /proc/zaptel/1 I see only 24 > >>> channels > >>> configured, and then, when I do a cat /proc/zaptel/2 I see the rest 7 > >>> channels. I > >>> setup the jumper correctly all closed to use the card in E1 mode.. I'm not > >>> sure what > >>> I did wrong here but the card should just display all 31 channels on span > >>> 1 > >>> (/proc/zaptel/1) instead of spreading it accross to the second span? > >>> > >>> Help is appreciated. Thank you. > > -- > Now accepting new clients in Birmingham, Atlanta, Huntsville, > Chattanooga, and Montgomery. > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > Asterisk-Users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- Asterisk-Users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users