How you do this depends on what you're getting from your phone company. I just configured mine for incoming POTS lines. I used three quad FXO cards and sent the output out to the T-100P. Worked great, and I didn't have to change any settings on the fxo cards to get them to work.
I started a thread on this very subject last month, so search the archives. Also, Bill Black was kind enough to give me the following (Thanks, Bill!) ............................. Hi John: A few thoughts on the Adtran: If it wasn't purchased new, you may want to update the firmware if it is very old. Pretty simple to do with a kermit session or your favorite terminal program. My settings are as follows: in zaptel.conf, make sure you have: span=1,0,0,esf,B8zs fxsks=1-12 in zapata.conf, make sure you have: signalling=fxs_ks channel => 1-12 With the above settings caller ID is coming through AOK here. If your T1 lights are happy (e.g. green) and your power supply is green there is a good chance you are working OK. (ztcfg -vv should also show problems if there are any.) If you do plug into the AD-750 serial port you can also look for module status. It will hopefull show channels as being 'in service'. Watch out for a red ringer supply light on your PSU. If you see this and can't reset it just send it back to adtran. They have a 10 year warranty. Bill Black ............................ You'll probably want a serial cable for connecting to the Adtran. You'll need it for upgrading the firmware. The firmware can be found at www.adtran.com Make sure and get the L36 version of the software. Here's the how-to on connecting to the Adtran: http://www.adtran.com/ADTRANPX/Doc/0/IPT0R456V3B139RT038BE81ID8/Connecting+a+termianl+or+PC+to+the+Craft+Port.htm As you can see, there are two ways to do it. The easy way is the DB-9 male to DB-9 female straight through cable. I had a heck of a problem connecting to this until I set the flow control to off on my terminal settings. Then it was easy. You can use minicom with the VT102 settings to connect to the Adtran. Don't forget to make a proper T-1 Crossover cable to connect to the T100P! There really isn't a whole lot to getting this up and running. It was one of the easiest hardware installations I've done. By the way, I've got three quad FXS cards I'm not using, if you're interested. John Baker ----- Original Message ----- From: "Michael Welter" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Saturday, February 14, 2004 9:33 AM Subject: Re: [Asterisk-Users] Adtran 750 - what do I need > I bought mine off of eBay. > > Each cabinet should contain a PSU board (power) and a BCU (control) > board. Then you have six slots for FXO/FXS cards. You'll also need the > power supply (which mounts on the side.) Some units have a cabinet > containing four 12V batteries. > > There are also two slots on for the V.35 interface, but we don.t use that. > > Warren H. Prince wrote: > > > Could anyone tell me what I need to include in the purchase of an Adtran > > 750 to work with a T100P? Obviously, I'd need a combination or FXO and > > FXS boards to fit my application, but, are there any other boards that > > are required? Does every Adtran include the proper port to connect to > > the T100P, or is that needed as well? Assuming it is not included, are > > the FXO, FXS and T1 cards all that is needed? > > > > Does anyone suggest a particular vendor for this piece of equipment? > > _______________________________________________ > > Asterisk-Users mailing list > > [EMAIL PROTECTED] > > http://lists.digium.com/mailman/listinfo/asterisk-users > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > > > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users