Hi, Thanks for taking time to answer.
> Not enough info in the above to hint at the problem. What linux > distro, SuSE Linux 8.2 2.4.20-4GB > what does your /etc/zaptel look like, For the TDM22B card: fxoks=1-2 fxsks=3-4 loadzone = uk defaultzone=uk > zapata.conf signalling=fxo_ks echocancel=yes echocancelwhenbridged=yes echotraining=400 callprogress=yes busydetect=1 busycount=7 relaxdtmf=yes channel => 1,2 signalling=fxs_ks group=2 context=incoming channel=> 3,4 > , what steps did you take to start the drivers (eg, modprobe, > ztcfg), etc. linux:~ # modprobe zaptel Warning: loading /lib/modules/2.4.20-4GB/misc/zaptel.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Module zaptel loaded, with warnings linux:~ # modprobe wctdm Warning: loading /lib/modules/2.4.20-4GB/misc/wctdm.o will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules Module wctdm loaded, with warnings linux:~ # ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS Kewlstart (Default) (Slaves: 04) 4 channels configured. linux:~ # > Since we're forced to guess at that stuff, here's a list of things > that might have an impact. > - ensure the definitions in /etc/zaptel.conf are reasonable Hope they are. > - run ztcfg -vvv from the command line. Any errors? No errors as above. > - run 'modprobe wctdm', any errors? The only message that shows is a warning about the kernel being tainted. I checked the link I was referred to and it should really have no effect on the operation of the card (s). > - what does dmesg, lspci, and lsmod output say? dmesg: Zapata Telephony Interface Registered on major 196 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1: Installed -- AUTO FXS/DPO Module 2: Installed -- AUTO FXO (FCC mode) Module 3: Installed -- AUTO FXO (FCC mode) Found a Wildcard TDM: Wildcard TDM400P REV H (4 modules) Registered tone zone 4 (United Kingdom) Registered tone zone 4 (United Kingdom) lspci: 00:00.0 Host bridge: VIA Technologies, Inc. P4M266 Host Bridge 00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] 00:0a.0 Communication controller: Tiger Jet Network Inc. Intel 537 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 50) 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74) 01:00.0 VGA compatible controller: S3 Inc. [ProSavageDDR K4M266] lsmod: Module Size Used by Tainted: P wctdm 25568 0 (unused) zaptel 183616 0 [wctdm] snd-pcm-oss 45888 0 (autoclean) snd-mixer-oss 13560 0 (autoclean) [snd-pcm-oss] isa-pnp 29672 0 (unused) ipv6 134388 -1 (autoclean) raw1394 14516 0 (unused) ieee1394 32880 0 [raw1394] via-rhine 12176 1 mii 2304 0 [via-rhine] snd-via8233 12516 0 snd-pcm 62912 0 [snd-pcm-oss snd-via8233] snd-timer 11904 0 [snd-pcm] snd-ac97-codec 31152 0 [snd-via8233] snd-mpu401-uart 3360 0 [snd-via8233] snd-rawmidi 13824 0 [snd-mpu401-uart] snd-seq-device 4000 0 [snd-rawmidi] snd 35940 0 [snd-pcm-oss snd-mixer-oss snd-via8233 snd-pcm snd-timer snd-ac97-codec snd-mpu401-uart snd-rawmidi snd-seq-device] soundcore 3396 0 [snd] reiserfs 200532 1 > - what does zttool show? I realized I need the package "libnewt" to get this to compile. Meanwhile does the above information reveal anything? Is there any BIOS setting I need to tweak? Thanks in advance. Rgds, Gerald. _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users