The output from lspci should have shown something like: 02:0a.0 Communication controller: Tiger Jet Network Inc. Intel 537 and its not there. Time to call/write digium support; suspect a bad card and probably related to pci bus, but that's a guess.
------------------------ > Hi, > > Thanks for taking time to answer. > > > Not enough info in the above to hint at the problem. What linux > > distro, > > SuSE Linux 8.2 2.4.20-4GB > > > what does your /etc/zaptel look like, > > For the TDM22B card: > > fxoks=1-2 > fxsks=3-4 > loadzone = uk > defaultzone=uk > > > zapata.conf > > signalling=fxo_ks > echocancel=yes > echocancelwhenbridged=yes > echotraining=400 > callprogress=yes > busydetect=1 > busycount=7 > relaxdtmf=yes > channel => 1,2 > signalling=fxs_ks > group=2 > context=incoming > channel=> 3,4 > > > , what steps did you take to start the drivers (eg, modprobe, > > ztcfg), etc. > > linux:~ # modprobe zaptel > Warning: loading /lib/modules/2.4.20-4GB/misc/zaptel.o will taint the > kernel: no license > See http://www.tux.org/lkml/#export-tainted for information about > tainted modules > Module zaptel loaded, with warnings > linux:~ # modprobe wctdm > Warning: loading /lib/modules/2.4.20-4GB/misc/wctdm.o will taint the > kernel: no license > See http://www.tux.org/lkml/#export-tainted for information about > tainted modules > Module wctdm loaded, with warnings > linux:~ # ztcfg -vvv > > Zaptel Configuration > ====================== > > > Channel map: > > Channel 01: FXO Kewlstart (Default) (Slaves: 01) > Channel 02: FXO Kewlstart (Default) (Slaves: 02) > Channel 03: FXS Kewlstart (Default) (Slaves: 03) > Channel 04: FXS Kewlstart (Default) (Slaves: 04) > > 4 channels configured. > > linux:~ # > > > Since we're forced to guess at that stuff, here's a list of things > > that might have an impact. > > - ensure the definitions in /etc/zaptel.conf are reasonable > > Hope they are. > > > - run ztcfg -vvv from the command line. Any errors? > > No errors as above. > > > - run 'modprobe wctdm', any errors? > > The only message that shows is a warning about the kernel being tainted. > I checked the link I was referred to and it should really have no effect > on the operation of the card (s). > > > - what does dmesg, lspci, and lsmod output say? > > dmesg: > Zapata Telephony Interface Registered on major 196 > Freshmaker version: 71 > Freshmaker passed register test > Module 0: Installed -- AUTO FXS/DPO > Module 1: Installed -- AUTO FXS/DPO > Module 2: Installed -- AUTO FXO (FCC mode) > Module 3: Installed -- AUTO FXO (FCC mode) > Found a Wildcard TDM: Wildcard TDM400P REV H (4 modules) > Registered tone zone 4 (United Kingdom) > Registered tone zone 4 (United Kingdom) > > lspci: > 00:00.0 Host bridge: VIA Technologies, Inc. P4M266 Host Bridge > 00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] > 00:0a.0 Communication controller: Tiger Jet Network Inc. Intel 537 > 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge > 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus > Master IDE (rev 06) > 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 > Audio Controller (rev 50) > 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev > 74) > 01:00.0 VGA compatible controller: S3 Inc. [ProSavageDDR K4M266] > > lsmod: > Module Size Used by Tainted: P > wctdm 25568 0 (unused) > zaptel 183616 0 [wctdm] > snd-pcm-oss 45888 0 (autoclean) > snd-mixer-oss 13560 0 (autoclean) [snd-pcm-oss] > isa-pnp 29672 0 (unused) > ipv6 134388 -1 (autoclean) > raw1394 14516 0 (unused) > ieee1394 32880 0 [raw1394] > via-rhine 12176 1 > mii 2304 0 [via-rhine] > snd-via8233 12516 0 > snd-pcm 62912 0 [snd-pcm-oss snd-via8233] > snd-timer 11904 0 [snd-pcm] > snd-ac97-codec 31152 0 [snd-via8233] > snd-mpu401-uart 3360 0 [snd-via8233] > snd-rawmidi 13824 0 [snd-mpu401-uart] > snd-seq-device 4000 0 [snd-rawmidi] > snd 35940 0 [snd-pcm-oss snd-mixer-oss snd-via8233 > snd-pcm snd-timer snd-ac97-codec snd-mpu401-uart snd-rawmidi > snd-seq-device] > soundcore 3396 0 [snd] > reiserfs 200532 1 > > > - what does zttool show? > > I realized I need the package "libnewt" to get this to compile. Meanwhile > does the above information reveal anything? Is there any BIOS setting I > need to tweak? > > Thanks in advance. > > Rgds, > Gerald. > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users ---------------End of Original Message----------------- _______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users