Matthew: After a long time pondering and thinking about the universe, I had finally decided to get packet sniffing (wireshark) installed. The packet snifer appears to have taken the problem away !!! "No more 200 ok on Register" !!!
Must be one of those Murphy law thingys. Cheers! Reza. ----- Original Message ----- From: "Matthew M. Gamble" <[EMAIL PROTECTED]> To: <[email protected]> Sent: Sunday, September 23, 2007 11:27 AM Subject: Re: [on-asterisk] Locating the source of "200 OK on REGISTER" Reza, What about doing a packet capture for all SIP packets coming into you Asterisk box? Once you see the error message in your logs, stop the capture, open it with Wireshark, and look for which endpoint send a 200 OK at the time of the error. You could also use Wiresharks builtin voip call analysis to break each SIP session down to see if any have really long delays between register and the ok. Hope that helps! Reza - Asterisk Enthusiast wrote: > Hello Nabeel: > > The only provisioning we have is for Aastra phones which we produced > in-house. Maybe we will write for other phones at a later time, but many > users are on soft phones. So unless they use Aastra phones, they are on > their own, and they (the clients) are pretty aware of it. > > " ..... As well as the IP, of course, but I guess if the device is not > registering correctly, you don't know who that IP belongs to :) " > -- ok... so now you understand my frustration :). > > But I still refuse to believe there is no way to pin point. I'm sure > there > is a way and there has to be a way... but I have not figured that out > yet! > > Cheers, > Reza. > > ----- Original Message ----- > From: "Nabeel Jafferali" <[EMAIL PROTECTED]> > To: <[email protected]> > Sent: Friday, September 21, 2007 7:18 PM > Subject: RE: [on-asterisk] Locating the source of "200 OK on REGISTER" > > > You don't change anything on the server side, it's the SIP timings on the > client side. You have hundreds of clients and have no provisioning set up > to > remotely administer them? > > Some endpoints support sending a S/N in the header of every SIP message, > sometimes by default and sometimes as an option - that would help you > identify the endpoint that is sending those SIP messages. As well as the > IP, > of course, but I guess if the device is not registering correctly, you > don't > know who that IP belongs to :) > > Nabeel > > >> -----Original Message----- >> From: Reza - Asterisk Enthusiast [mailto:[EMAIL PROTECTED] >> Sent: September 21, 2007 3:52 PM >> To: [email protected] >> Subject: Re: [on-asterisk] Locating the source of "200 OK on REGISTER" >> >> Hello Nabeel: >> >> I was afraid someone would suggest that. But the number of sip >> registers we >> have, and to change the SIP timings for "qualify" is not practical for >> the >> number of registrations we have. We do not have any satellite >> registrations, but we do have overseas registrations. I suspected it >> might >> have been some of the overseas clients, but their connection is stable >> and >> rock solid. >> >> Which leaves me to think that the 200 OK on Register is being generated >> by a >> North American account/client, but unfortunately its not practical on >> our >> part to change the "qualify" seconds. >> >> I'm still looking for some sort of answer/recommendation on how we can >> pin >> point the source... sort of take a magnet in a hay stack, swipe it >> over and >> get the needle... versus trying to find the needle in the hay stack, >> moving >> one hay at a time. >> >> Any suggestions? >> >> Cheers! >> Reza. >> >> >> ----- Original Message ----- >> From: "Nabeel Jafferali" <[EMAIL PROTECTED]> >> To: <[email protected]> >> Sent: Friday, September 21, 2007 6:57 AM >> Subject: RE: [on-asterisk] Locating the source of "200 OK on REGISTER" >> >> >> Usually to do with a significant delay, when the endpoint receives the >> Asterisk reply very late compared to the REGISTER message it sent. My >> experience was this was happening with endpoints with satellite >> Internet >> connectivity. >> >> Increase the SIP timings (I just quadrupled them from their default) >> and the >> problem should go away, since the device will have a higher tolerance >> for >> delay. >> >> Nabeel >> >> >>> -----Original Message----- >>> From: Reza - Asterisk Enthusiast [mailto:[EMAIL PROTECTED] >>> Sent: September 21, 2007 12:46 AM >>> To: [email protected] >>> Subject: [on-asterisk] Locating the source of "200 OK on REGISTER" >>> >>> Hello all: >>> >>> The "Got 200 OK on REGISTER that isn't a register" is annoying the >>> >> day >> >>> lights out of me. I know what it means... but do not know how to >>> PIN >>> POINT the source. Any suggestions? >>> >>> Best, >>> Reza. >>> >>> >>> >>> --------------------------------------------------------------------- >>> To unsubscribe, e-mail: [EMAIL PROTECTED] >>> For additional commands, e-mail: [EMAIL PROTECTED] >>> >> --------------------------------------------------------------------- >> To unsubscribe, e-mail: [EMAIL PROTECTED] >> For additional commands, e-mail: [EMAIL PROTECTED] >> >> >> >> >> --------------------------------------------------------------------- >> To unsubscribe, e-mail: [EMAIL PROTECTED] >> For additional commands, e-mail: [EMAIL PROTECTED] >> > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
