Hi All, I put 0.4.2 onto a CF card today and tried to boot it in my Soekris Net4801. No joy I'm afraid. I tried with and without the USB stick from the old 0.3.x installation. Here is the terminal output. Can anyone tell me what I did wrong?
--- The highlighted entry will be booted automatically in 3 seconds. [5;75H[23;4HThe highlighted entry will be booted automatically in 2 seconds. [5;75H[23;4HThe highlighted entry will be booted automatically in 1 seconds. [5;75H[H[J Booting 'AstLinux (Boot from CF - Use USB KeyDisk)' root (hd0,0) Filesystem type is ext2fs, partition type 0x83 kernel /boot/bzImage root=/dev/hda1 console=ttyS0,19200n8 astlinux=net4801 astk d=/dev/sda1 astopt=/dev/hda2 ide=nodma [Linux-bzImage, setup=0x1400, size=0x11288d] savedefault [6nLinux version 2.6.16.12 ([EMAIL PROTECTED]) (gcc version 3.4.2) #1 PREEMPT Thu Jul 20 18:30:16 EDT 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000008000000 (usable) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 128MB LOWMEM available. DMI not present or invalid. Allocating PCI resources starting at 10000000 (gap: 08000000:f7f00000) Built 1 zonelists Kernel command line: root=/dev/hda1 console=ttyS0,19200n8 astlinux=net4801 astkd=/dev/sda1 astopt=/dev/hda2 ide=nodma ide_setup: ide=nodma : Prevented DMA Initializing CPU#0 PID hash table entries: 1024 (order: 10, 16384 bytes) scx200hr: timer not yet accessible; will probe later. Detected 266.655 MHz processor. Using tsc for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 127028k/131072k available (1418k kernel code, 3624k reserved, 557k data, 116k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 534.31 BogoMIPS (lpj=267159) Mount-cache hash table entries: 512 CPU: NSC Unknown stepping 01 Checking 'hlt' instruction... OK. NET: Registered protocol family 16 PCI: PCI BIOS revision 2.01 entry at 0xf7861, last bus=0 PCI: Using configuration type 1 Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: PnP BIOS support was not detected. SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware TC classifier action (bugs to [email protected] cc [EMAIL PROTECTED]) scx200: NatSemi SCx200 Driver scx200: GPIO base 0x6100 scx200: Configuration Block base 0x6000 switching to scx200 high-resolution timer (255961 cpt) Initializing Cryptographic API io scheduler noop registered io scheduler cfq registered (default) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac PNP: No PS/2 controller found. Probing ports directly. i8042.c: Can't read CTR while initializing i8042. Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SC1200: IDE controller at PCI slot 0000:00:12.2 SC1200: chipset revision 1 SC1200: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:pio hdb: LEXAR ATA FLASH, CFA DISK drive SC1200: set xfer mode failure ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdb: max request size: 128KiB hdb: 503808 sectors (257 MB) w/1KiB Cache, CHS=984/16/32 hdb: hdb1 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:13.0: irq 11, io mem 0xa0003000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode VFS: Cannot open root device "hda1" or unknown-block(0,0) Please append a correct "root=" boot option Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) --- Michael -- Michael Graves [EMAIL PROTECTED] Sr. Product Specialist www.pixelpower.com Pixel Power Inc. [EMAIL PROTECTED] o713-861-4005 o800-905-6412 c713-201-1262 fwd 54245 _______________________________________________ Astlinux-users mailing list [email protected] http://lists.kriscompanies.com/mailman/listinfo/astlinux-users Donations to support AstLinux are graciously accepted via PayPal to [EMAIL PROTECTED]
