On 10/23/2009 04:31 AM, Tom Chadwin wrote: >> -----Original Message----- >> From: Philip A. Prindeville >> [mailto:philipp_s...@redfish-solutions.com] >> Sent: 16 October 2009 03:15 >> To: astlinux-users@lists.sourceforge.net >> Subject: Re: [Astlinux-users] Getting Berofix to work in >> net5501 with Astlinux 0.6.7 >> >> On 10/15/2009 10:09 AM, Lonnie Abelbeck wrote: >> >>> On Oct 15, 2009, at 4:32 AM, Tom Chadwin wrote: >>> >>> >>>>> This will work if the 8139too module is enabled in >>>>> >> /etc/rc.modules, >> >>>>> but if "modprobe 8139too" is called in /mnt/kd/rc.elocal >>>>> >> the BRIDGE0 >> >>>>> variable won't work as expected if any of the bridged >>>>> >> interfaces are >> >>>>> not defined until /mnt/kd/rc.elocal is called. Advanced >>>>> >> users could >> >>>>> place the 'brctl' calls in rc.elocal if they wish. >>>>> >>>>> >>>> The documentation says this: >>>> >>>> "In this example eth1 is the berofix card and eth0 is our >>>> >> interface >> >>>> to the LAN. We want to apply our LAN interface the ip-address >>>> 192.168.0.2 and our berofix device the ip-address >>>> >> 192.168.0.3. After >> >>>> we setup the Bridge we want to access the berofix device from all >>>> devices in our LAN which are all in the network >>>> >> 192.168.0.1-254. To >> >>>> setup this bridge, you need to enter a few commands like in the >>>> following >>>> example: >>>> >>>> berofix:# ifconfig eth0 0.0.0.0 up >>>> berofix:# ifconfig eth1 0.0.0.0 up >>>> berofix:# brctl addbr br0 >>>> berofix:# brctl addif br0 eth0 >>>> berofix:# brctl addif br0 eth1 >>>> berofix:#ifconfig br0 192.168.0.2 up >>>> >>>> "These commands will first remove the ip-addresses from >>>> >> your network >> >>>> cards, then will create the bridge and add your network >>>> >> card and the >> >>>> berofix card to this bridge. In this case the bridge gets the >>>> IP-address 192.168.0.2. The default IP of the berofix is 10.0.0.2 >>>> with the subnet 255.0.0.0 and we have to change this with the >>>> bfdetect tool to 192.168.0.3 with 255.255.255." >>>> >>>> So would putting that into rc.elocal do the trick, do we >>>> >> think? Not >> >>>> worked with either bridges or ip forwarding before, so I'm flying >>>> somewhat in the dark here. As I say, Beronet recommend the bridge >>>> approach, so it might be nice to get that working. >>>> >>>> >>> Tom, you need one "modprobe bridge" before the first >>> >> 'brctl' command. >> >>> To make it look like /etc/init.d/network, something like: >>> >>> -- rc.elocal snip -- >>> >>> modprobe 8139too >>> modprobe bridge >>> >>> EXTIF="br0" >>> BRIDGE0="eth0 eth1" >>> >>> brctl addbr $EXTIF >>> brctl setfd $EXTIF 0 >>> for i in $BRIDGE0; do >>> ifconfig $i 0.0.0.0 up >>> brctl addif $EXTIF $i >>> done >>> ifconfig $EXTIF $EXTIP netmask $EXTNM up if [ -n "$EXTGW" ]; then >>> route add -net default gw $EXTGW dev $EXTIF fi >>> -- snip -- >>> >>> In the Network tab set External Interface: br0 with >>> >> Connection Type: >> >>> Static IP, define Static IP:/NetMask:/Gateway: >>> >>> I have not tested this, so expect errors, but should give you >>> something to test. >>> >>> >> I wouldn't recommend using /mnt/kd/rc.elocal in this case. >> >> Edit /etc/rc.modules to add/enable the module. >> >> Modify /mnt/kd/rc.conf to set BRIDGE0 and EXTIF as above (or as >> appropriate). >> > This would not work for me, as I mentioned, because if I try to use > rc.modules to enable the 8139too driver, the box boots with the > Berofix interface as eth0, and hence as $EXTIF, so I can get no access > to the box. Even changing the order of the modules in rc.modules did > not solve this problem. This is why I am modprobing 8139too in > rc.elocal. > > I shall try to get a bridge up and running today. > > Thanks again > > Tom >
This would be so much easier if you were running 0.7... -Philip ------------------------------------------------------------------------------ Come build with us! The BlackBerry(R) Developer Conference in SF, CA is the only developer event you need to attend this year. Jumpstart your developing skills, take BlackBerry mobile applications to market and stay ahead of the curve. Join us from November 9 - 12, 2009. Register now! http://p.sf.net/sfu/devconference _______________________________________________ Astlinux-users mailing list Astlinux-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/astlinux-users Donations to support AstLinux are graciously accepted via PayPal to pay...@krisk.org.