Many thanks for your fast help! I've made some progress, but ran into other problems. If i compile ath10_pci, ath10k_core and ath from kvalo's tree and load them, i get following dmesg output:
[ 2.980448] ath10k_pci 0000:06:00.0: enabling device (0000 -> 0002) [ 2.980750] ath10k_pci 0000:06:00.0: pci irq msi-x interrupts 8 irq_mode 0 reset_mode 0 [ 3.158860] ath10k_pci 0000:06:00.0: Direct firmware load for ath10k/cal-pci-0000:06:00.0.bin failed with error -2 [ 3.159611] ath10k_pci 0000:06:00.0: Direct firmware load for ath10k/QCA6174/hw2.1/board-pci-168c:003e:1a56:1525.bin failed with error -2 [ 3.159613] ath10k_pci 0000:06:00.0: failed to load spec board file, falling back to generic: -2 [ 3.159922] ath10k_pci 0000:06:00.0: Direct firmware load for ath10k/QCA6174/hw2.1/firmware-5.bin failed with error -2 [ 3.159924] ath10k_pci 0000:06:00.0: could not fetch firmware file 'ath10k/QCA6174/hw2.1/firmware-5.bin': -2 [ 4.360946] ath10k_pci 0000:06:00.0: qca6174 hw2.1 (0x05010000, 0x003405ff, 168c:003e:1a56:1525 fallback) fw killer-n1525-fw api 4 htt 3.1 wmi 4 cal otp max_sta 32 [ 4.360950] ath10k_pci 0000:06:00.0: debug 1 debugfs 1 tracing 1 dfs 0 testmode 0 [ 4.430068] ath: EEPROM regdomain: 0x6c [ 4.430070] ath: EEPROM indicates we should expect a direct regpair map [ 4.430072] ath: Country alpha2 being used: 00 [ 4.430072] ath: Regpair used: 0x6c [ 4.430078] ath10k_pci 0000:06:00.0: failed to register ieee80211: -22 [ 4.430097] ath10k_pci 0000:06:00.0: could not register to mac80211 (-22) So I compiled mac80211, and tried to load it. What i get is a load of that messages: [ 226.812494] mac80211: Unknown symbol cfg80211_cqm_rssi_notify (err -22) [ 226.812497] mac80211: disagrees about version of symbol cfg80211_auth_timeout [ 226.812497] mac80211: Unknown symbol cfg80211_auth_timeout (err -22) [ 226.812498] mac80211: disagrees about version of symbol cfg80211_rx_unprot_mlme_mgmt [ 226.812499] mac80211: Unknown symbol cfg80211_rx_unprot_mlme_mgmt (err -22) Because mac80211 depends on cfg80211, i compilied and tested it. The error messages reduced to [ 632.208849] mac80211: Unknown symbol rhashtable_insert_rehash (err 0) [ 632.208881] mac80211: Unknown symbol rhashtable_insert_slow (err 0) Know I'm stuck. I'll try to compile and use the whole kernel (it's compiling right now), but would prefer to just change the modules. The firmware-4.bin is assembled like described in this thread, as board.bin i used eeprom_qca9377_1p0_NFA435_olpc.bin. Any Ideas? :) Happy greetings Moritz 2015-04-27 23:56 GMT+02:00 Corin Lawson <m...@corinlawson.com.au>: > Gabriele is right it is only the modules that need to be built kvalo's > kernel > > On 28 Apr 2015 1:05 am, "Gabriele Martino" <g.mart...@gmx.com> wrote: >> >> On 27/04/2015 16:00, Moritz Morawietz wrote: >> > Hi! >> > >> > I have the same problems with my card (also a Killer N1525). It seems >> > you've done it, but i can't figure out how. >> > >> > Do i need to build and use kvalo's kernel, or is it enough to build >> > the modules ath10k_core & ath10k_pci? >> > I'm a bit afraid of compiling the whole kernel ^^ >> > output of uname -a: >> > Linux companion 4.0.0-2-ARCH #1 SMP PREEMPT Tue Apr 14 07:14:46 CEST >> > 2015 x86_64 GNU/Linux >> The modules should be enough. Tell us if it works. >> Compiling a whole kernel isn't too hard if you already have a working >> configuration. >> >> > I have the disassembly.py, but cannot find the dissect.py, can you >> > provide the link? Or, even better, the assembled files? >> I won't upload the assembled files now, I don't know if I can get >> licensing issues. >> You can find the dissect.py script here: >> http://lists.infradead.org/pipermail/ath10k/2015-April/005074.html >> >> Good luck! >> >> Regards, >> Gabriele >> >> >> _______________________________________________ >> ath10k mailing list >> ath10k@lists.infradead.org >> http://lists.infradead.org/mailman/listinfo/ath10k _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k