I used 4.0.0-2. Also i had one kernel build where it worked, but, because I didn't knew that you have to install nvidia drivers again, I deletet it. I am not sure how i did it, so I'm currently trying again. Maybe I need to understand the patching mechanisms, guess that would help :D I did something with git…
Thank you a lot for your help so far! 2015-04-30 2:07 GMT+02:00 Gabriele Martino <g.mart...@gmx.com>: > On 28/04/2015 13:55, Moritz Morawietz wrote: >> Many thanks for your fast help! >> >> I've made some progress, but ran into other problems. >> If i compile ath10_pci, ath10k_core and ath from kvalo's tree and load >> them, i get following dmesg output: >> >> [ 2.980448] ath10k_pci 0000:06:00.0: enabling device (0000 -> 0002) >> [ 2.980750] ath10k_pci 0000:06:00.0: pci irq msi-x interrupts 8 >> irq_mode 0 reset_mode 0 >> [ 3.158860] ath10k_pci 0000:06:00.0: Direct firmware load for >> ath10k/cal-pci-0000:06:00.0.bin failed with error -2 >> [ 3.159611] ath10k_pci 0000:06:00.0: Direct firmware load for >> ath10k/QCA6174/hw2.1/board-pci-168c:003e:1a56:1525.bin failed with >> error -2 >> [ 3.159613] ath10k_pci 0000:06:00.0: failed to load spec board >> file, falling back to generic: -2 >> [ 3.159922] ath10k_pci 0000:06:00.0: Direct firmware load for >> ath10k/QCA6174/hw2.1/firmware-5.bin failed with error -2 >> [ 3.159924] ath10k_pci 0000:06:00.0: could not fetch firmware file >> 'ath10k/QCA6174/hw2.1/firmware-5.bin': -2 >> [ 4.360946] ath10k_pci 0000:06:00.0: qca6174 hw2.1 (0x05010000, >> 0x003405ff, 168c:003e:1a56:1525 fallback) fw killer-n1525-fw api 4 htt >> 3.1 wmi 4 cal otp max_sta 32 >> [ 4.360950] ath10k_pci 0000:06:00.0: debug 1 debugfs 1 tracing 1 >> dfs 0 testmode 0 >> [ 4.430068] ath: EEPROM regdomain: 0x6c >> [ 4.430070] ath: EEPROM indicates we should expect a direct regpair map >> [ 4.430072] ath: Country alpha2 being used: 00 >> [ 4.430072] ath: Regpair used: 0x6c >> [ 4.430078] ath10k_pci 0000:06:00.0: failed to register ieee80211: -22 >> [ 4.430097] ath10k_pci 0000:06:00.0: could not register to mac80211 (-22) >> >> So I compiled mac80211, and tried to load it. What i get is a load of >> that messages: >> >> [ 226.812494] mac80211: Unknown symbol cfg80211_cqm_rssi_notify (err -22) >> [ 226.812497] mac80211: disagrees about version of symbol >> cfg80211_auth_timeout >> [ 226.812497] mac80211: Unknown symbol cfg80211_auth_timeout (err -22) >> [ 226.812498] mac80211: disagrees about version of symbol >> cfg80211_rx_unprot_mlme_mgmt >> [ 226.812499] mac80211: Unknown symbol cfg80211_rx_unprot_mlme_mgmt (err >> -22) >> >> Because mac80211 depends on cfg80211, i compilied and tested it. The >> error messages reduced to >> >> [ 632.208849] mac80211: Unknown symbol rhashtable_insert_rehash (err 0) >> [ 632.208881] mac80211: Unknown symbol rhashtable_insert_slow (err 0) >> >> Know I'm stuck. I'll try to compile and use the whole kernel (it's >> compiling right now), but would prefer to just change the modules. > I could find some references to "rhashtable_insert_rehash" with grep: > /usr/src/linux/lib/rhashtable.c:int rhashtable_insert_rehash(struct > rhashtable *ht) > /usr/src/linux/lib/rhashtable.c:EXPORT_SYMBOL_GPL(rhashtable_insert_rehash); > > This file is present in 3.18.11 kernel (I don't have older sources on > this laptop). > Which distribution and kernel are you using? > You are compiling 4.0 (-> 3.20) modules, so you're likely to get strange > issues if your kernel is too old. > > Regards, > Gabriele > > > _______________________________________________ > ath10k mailing list > ath10k@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/ath10k _______________________________________________ ath10k mailing list ath10k@lists.infradead.org http://lists.infradead.org/mailman/listinfo/ath10k