Thanks for the info,

I have moved on a lot further since using pre-compiled toolchains (even though its sorta
cheating) ;)

I grabbed the latest kernel26 code from handhelds.org CVS and followed the instructions
from http://www.fisherss.com/ownkernel.html

First problem I encountered was:

CC      arch/arm/mach-pxa/aximx30/aximx30.o
arch/arm/mach-pxa/aximx30/aximx30.c:288: warning: implicit declaration of function
'MAINTAINER'
arch/arm/mach-pxa/aximx30/aximx30.c:289: error: initializer element is not constant
arch/arm/mach-pxa/aximx30/aximx30.c:289: error: (near initialization for
'__mach_desc_X30.boot_params')
arch/arm/mach-pxa/aximx30/aximx30.c:289: error: syntax error before 'BOOT_MEM'
arch/arm/mach-pxa/aximx30/aximx30.c:289: error: syntax error before ')' token

Looking at a few other implementations containing the ?MACHINE_START? macro I edited
aximx30.c

/*
MACHINE_START(X30, "Dell Axim X30")
      MAINTAINER("Giuseppe Zompatori, <[EMAIL PROTECTED]>")
      BOOT_MEM(0xa8000000, 0x40000000, io_p2v(0x40000000))
      BOOT_PARAMS(0xa8000100)
      MAPIO(x30_map_io)
      INITIRQ(x30_init_irq)
      .timer = &pxa_timer,
      .init_machine = x30_init,
MACHINE_END
*/

MACHINE_START(X30, "Dell Axim X30")
      /* Maintainer: Giuseppe Zompatori, <[EMAIL PROTECTED]> */
      .phys_ram       = 0xa8000000,
      .phys_io        = 0x40000000,
      .io_pg_offst    = (io_p2v(0x40000000) >> 18) & 0xfffc,
      .boot_params    = 0xa8000100,
      .map_io         = x30_map_io,
      .init_irq       = x30_init_irq,
      .timer = &pxa_timer,
      .init_machine = x30_init,
MACHINE_END

This fix gets around that problem and the kernel build gets further and then fails again
with:

CC      drivers/serial/pxa.o
drivers/serial/pxa.c:762: error: static declaration of 'serial_pxa_ports' follows
non-static declaration
drivers/serial/pxa.c:612: error: previous declaration of 'serial_pxa_ports' was here
drivers/serial/pxa.c:770: error: initializer element is not constant
drivers/serial/pxa.c:770: error: (near initialization for
'serial_pxa_ports[0].port.mapbase')
drivers/serial/pxa.c:784: error: initializer element is not constant
drivers/serial/pxa.c:784: error: (near initialization for
'serial_pxa_ports[1].port.mapbase')
drivers/serial/pxa.c:798: error: initializer element is not constant
drivers/serial/pxa.c:798: error: (near initialization for
'serial_pxa_ports[2].port.mapbase')
drivers/serial/pxa.c:812: error: initializer element is not constant
drivers/serial/pxa.c:812: error: (near initialization for
'serial_pxa_ports[3].port.mapbase')
drivers/serial/pxa.c:822: error: static declaration of 'serial_pxa_reg' follows
non-static declaration
drivers/serial/pxa.c:613: error: previous declaration of 'serial_pxa_reg' was here

To 'hack' around this I edited 'aximx30_defconfig' setting the following to 'n' instead
of 'y'.

CONFIG_SERIAL_PXA=n
CONFIG_SERIAL_PXA_CONSOLE=n

Now I have the kernel completing builds cleanly but so far haven't done anything with it. However I don't know if ?SERIAL_PXA? is required for the use of the Axim serial port,
this is literally just a hack to get the thing compiling.

I don't have a serial cable for my Axim as yet so I can't see kernel output. What is the state of the x50v stuff? Is there any graphical output in working builds yet? Does anyone have a 'working' x50v setup (kernel, initrd, rootfs etc.) I can see / test on my device?

Cheers,

Michael


Quoting JeDi <[EMAIL PROTECTED]>:

Have a look here: http://www.handhelds.org/moin/moin.cgi/PrebuiltToolchains

Good luck!

Greetz,
JeDi





--
_______________________________________________
Aximx50-port mailing list
[email protected]
https://www.handhelds.org/mailman/listinfo/aximx50-port

Reply via email to