Hi
> > Set the switches to boot from SD on the mx25 device and power on. It > > successfully loads barebox and I can mount the fat partition (of course > the > > other partition is unmountable, because there is no ext2/3 support in > > barebox). Booting from my environment currently fails, but I reckon it > has > > to do with my configuration settings. Here is where it gets so far: > > .../... > > [ 103.029081] VFS: Unable to mount root fs via NFS, trying floppy. > > [ 103.036763] VFS: Cannot open root device "nfs" or unknown-block(2,0) > > [ 103.043157] Please append a correct "root=" boot option; here are the > > available partitions: > > [ 103.052007] b300 1955840 mmcblk0 driver: mmcblk > > [ 103.057512] b301 1024 mmcblk0p1 > > 00000000-0000-0000-0000-000000000mmcblk0p1 > > [ 103.065670] b302 524288 mmcblk0p2 > > 00000000-0000-0000-0000-000000000mmcblk0p2 > > [ 103.073744] b303 1429504 mmcblk0p3 > > 00000000-0000-0000-0000-000000000mmcblk0p3 > > .../... > > Thank you very much for your pointers. > > > add to your bootargs root=/dev/mmcblk0p3 rootfstype=ext3 or something > like this > > I haven't found a combination of root/rootfstype yet that permits me to boot from barebox either from NFS, TFTP, MMC/SD or NOR yet. No matter what I try, the kernel spits back at me. Also I have the problem that my NOR is only detected when using barebox as a second stage boot loader from uboot. If booting from SD into barebox, the NOR is not detected. I have added the following changes to figure out what's going on: diff --git a/drivers/nor/cfi_flash.c b/drivers/nor/cfi_flash.c index 654e647..7884ca4 100644 --- a/drivers/nor/cfi_flash.c +++ b/drivers/nor/cfi_flash.c @@ -990,13 +990,17 @@ static int cfi_probe (struct device_d *dev) info->size = flash_get_size(info); if (info->flash_id == FLASH_UNKNOWN) { - printf ("## Unknown FLASH on Bank at 0x%08x - Size = 0x%08lx = %ld MB\n", + printf("## Unknown FLASH on Bank at 0x%08x - Size = 0x%08lx = %ld MB\n", dev->resource[0].start, info->size, info->size << 20); + printf("cfi flash (id=%08lX vend=%06X manu=%06X devid=%06X extid=%06X)\n", + info->flash_id, info->vendor, info->manufacturer_id, info->device_id, + info->device_id2); return -ENODEV; } - dev_info(dev, "found cfi flash at %p, size %ld\n", - info->base, info->size); + dev_info(dev, "cfi flash (id=%08lX vend=%06X manu=%06X devid=%06X extid=%06X) at %p, size %ldMB + info->flash_id, info->vendor, info->manufacturer_id, info->device_id, + info->device_id2, info->base, info->size/1024/1024); info->cdev.name = asprintf("nor%d", dev->id); info->cdev.size = info->size; Loading barebox as second stage bootloader gives me following output: [...] cfi_flash@cfi_flash0: cfi flash (id=01000000 vend=000002 manu=000001 devid=00007E extid=002301) at a0000000, size 64MB [...] Loading barebox as a first stage bootloader directly from SD card results in the following: [...] ## Unknown FLASH on Bank at 0xa0000000 - Size = 0x00000000 = 0 MB cfi flash (id=0000FFFF vend=000000 manu=000000 devid=000000 extid=000000) [...] What's going on here? Best regards Roberto
_______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox