Hmm. Maybe go to the support wiki??? http://circuitco.com/support/index.php?title=Updating_The_Software#Checking_The_Angstrom_Image_Version
Gerald On Sun, Oct 27, 2013 at 1:52 PM, Limpy <asp1...@gmail.com> wrote: > # cat /etc/dogtag > will display the version of Angstrom installed on the device. > Once the eMMC is flashed successfully, the four USR LEDs will remain lit. > > > > On Sunday, October 27, 2013 7:08:11 AM UTC+5:30, Michael Vittiglio wrote: >> >> Gerald, >> I got the device today and I wanted to upgrade the firmware. Before I do >> that I wanted to ask if there's any way I can verify what's already >> installed and therefore know if I actually succeeded in updating the unit. >> Thanks for your help. >> >> On Wednesday, October 9, 2013 11:47:56 AM UTC-4, Gerald wrote: >>> >>> Yes it is covered. >>> >>> Gerald >>> >>> >>> >>> On Wed, Oct 9, 2013 at 10:08 AM, Michael Vittiglio < >>> michael....@gmail.com> wrote: >>> >>>> I purchased this unit at the Maker Faire (NYC a few weeks back). Does >>>> this unit still apply to RMA? >>>> >>>> I don't mind getting my hands a bit dirtier but it's hard to find >>>> documentation online. Is there a way we can blast/test it via FTDI (if not >>>> some other method)? >>>> >>>> >>>> On Wednesday, October 9, 2013 10:52:52 AM UTC-4, Gerald wrote: >>>> >>>>> Then I suggest you request an RMA and let the factory folks do it for >>>>> you. >>>>> >>>>> Gerald >>>>> >>>>> >>>>> >>>>> On Mon, Oct 7, 2013 at 9:53 PM, Michael Vittiglio < >>>>> michael....@gmail.com> wrote: >>>>> >>>>>> Based on the instructions provided I've done everything to the >>>>>> letter. Unfortunately, this is all I see via the FTDI output via the >>>>>> terminal command "screen /dev/tty.usb... 115200": >>>>>> U-Boot SPL 2013.04-dirty (Jun 19 2013 - 09:57:14) >>>>>> musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, HB-ISO Rx, HB-ISO Tx, >>>>>> SoftConn) >>>>>> >>>>>> On Friday, October 4, 2013 9:24:43 AM UTC-4, Gerald wrote: >>>>>> >>>>>>> That indicates there is nothing in flash and nothing on the SD card >>>>>>> that it can boot from. >>>>>>> >>>>>>> Gerald >>>>>>> >>>>>>> >>>>>>> >>>>>>> On Fri, Oct 4, 2013 at 7:16 AM, Charles Steinkuehler < >>>>>>> cha...@steinkuehler.net> wrote: >>>>>>> >>>>>>>> On 10/4/2013 6:46 AM, Michael Vittiglio wrote: >>>>>>>> > When trying to view what's happening via the FTDI the unity >>>>>>>> basically puts >>>>>>>> > out no output with the exception of the occasional "C". Is there >>>>>>>> any chance >>>>>>>> > that this can be repaired? As stated earlier in this thread, the >>>>>>>> "boot >>>>>>>> > button" option does not seem to work. >>>>>>>> >>>>>>>> The boot button completely bypasses the on-board eMMC, so if your >>>>>>>> 'bone >>>>>>>> is not booting correctly from SD card when holding the boot button >>>>>>>> during reset, you need to re-image the SD card. >>>>>>>> >>>>>>>> -- >>>>>>>> Charles Steinkuehler >>>>>>>> cha...@steinkuehler.net >>>>>>>> >>>>>>>> >>>>>>> -- >>>>>> For more options, visit http://beagleboard.org/discuss >>>>>> --- >>>>>> You received this message because you are subscribed to the Google >>>>>> Groups "BeagleBoard" group. >>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>> send an email to beagleboard...@**googlegroups.**com. >>>>>> >>>>>> For more options, visit >>>>>> https://groups.google.com/**grou**ps/opt_out<https://groups.google.com/groups/opt_out> >>>>>> . >>>>>> >>>>> >>>>> -- >>>> For more options, visit http://beagleboard.org/discuss >>>> --- >>>> You received this message because you are subscribed to the Google >>>> Groups "BeagleBoard" group. >>>> To unsubscribe from this group and stop receiving emails from it, send >>>> an email to beagleboard...@googlegroups.**com. >>>> For more options, visit >>>> https://groups.google.com/**groups/opt_out<https://groups.google.com/groups/opt_out> >>>> . >>>> >>> >>> -- > For more options, visit http://beagleboard.org/discuss > --- > You received this message because you are subscribed to the Google Groups > "BeagleBoard" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to beagleboard+unsubscr...@googlegroups.com. > For more options, visit https://groups.google.com/groups/opt_out. > -- For more options, visit http://beagleboard.org/discuss --- You received this message because you are subscribed to the Google Groups "BeagleBoard" group. To unsubscribe from this group and stop receiving emails from it, send an email to beagleboard+unsubscr...@googlegroups.com. For more options, visit https://groups.google.com/groups/opt_out.